Lightmybricks LEGO Disney Train Station 71044 User manual

Please note: This page lists instructions for the LED light kit only.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the
cable and light.

Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be
inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on
the left side of the port. The connector side with the wires exposed should be facing toward the
soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do
not force it.
Incorrectly inserting the connector can can result in bent pins inside the port or possible
overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the
connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector,
don’t force it. Doing so will damage the plug and the connector.

Connecting Micro Cable connectors to Micro Expansion Board
Ports
Take extra care when inserting the micro connectors to micro ports of Micro Expansion Boards.
Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting lights and cables
to Strip Lights. With the expansion board facing up, ensure the side of the connector with the
wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use
your fingernail to push the plastic part of the connector to the micro port.
Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow
LED component exposed). You can either place them directly on top of LEGO® studs or in
between.

OK, Let’s Begin!
Installing lights to the Disney Train
1.) Disconnect the train carriages, then take the first carriage and disconnectsections from
the top and front of the vehicle.

Place the train onto it’s right side and disconnect the front wheel section, then disconnect the
gold round plate from each side.

2.) Take one of the gold plates and thread the connector end of a White 15cm Bit Light
through the front of it. Thread it all the way through, then carefully bend the Bit Light so that it
sits flat against the edge of the plate. Secure the LED in place by connecting a provided LEGO
Trans Clear Round Plate 1×1 over the top.

Repeat this step to install another White 15cm Bit Light to the other gold plate, securing it in
place with another provided Trans Clear Round Plate 1×1.
3.) Reconnect each plate to the front wheel section, ensuring the cables arefacing toward
the inside, then cross both cables over each other and secure them underneath the following
dark grey arched plate. Ensure the cables are neatly laid in between studs underneath.

4.) Take the top front section of the train and disconnect the following twoplates. Take a
Warm White 30cm Large Bit Light and with the cable facing down, place it in the following
position on the front section. Secure the Bit Light in place by reconnecting the trans yellow 2×2
plate. Bring the cable down underneath, then reconnect the red 1×2 tile.

Reconnect this section to the front of the train, then push down the large bit light cable and lay
it down in between studs. Reconnect the two outer sections as shown below.
5.) Place the train onto it’s right side, then bend the large bit light cable into ahook shape.
Thread the cable over the following technic axle, then pull it all the way out from the other
side. Connect the cable to a 6-Port Expansion Board.

Reconnect the front wheel section to the train, then connect the two bit light cables from the
front to the 6-Port Expansion Board.

6.) Take the second carriage and disconnect the motor cable from the LEGOpowered up
battery box. Remove the battery box from the carriage, then take out the Light My Bricks
Powered Up Cable and connect it to the battery box.

Connect the other end of the cable to the 6-Port Expansion Board. Turn ON the battery box and
ensure that it is paired to your remote control or smartphone app. Press the “+” button on the
controller (on the A side) or “+” on the Smartphone App to test the lights are turning ON and
working OK.

Important Note: If using the smartphone App to control the lights and motor, the lights will
only turn on when the train is in “accelerate or reverse mode )+ or -)”. The lights will
automatically turn off when the motor is turned off or when “STOP” on the controller/app is
pressed.
Note: If you experience any issues with the lights not working and suspect an issue with a
component, please try a different port on the expansion board to verify where the fault lies (with
the light or expansion board). To correct any issues with expansion board ports, please view the
section addressing expansion board issues on our online troubleshooting guide.
7.) From the back of the train, lift up the roof, then take a White 15cm Bit Light, and with the
cable facing down, place it in the following position underneath the roof. Secure the Bit Light in
place by connecting a provided Trans Clear Plate w Rounded Bottom 2×2 over the top.

Thread the Bit Light cable down and out the side of the train. Turn the train over onto it’s right
side and pull the cable all the way out from the bottom. Bend the cable into a hook shape and
thread it down the space of the black brick with handle. Pull the cable all the way out from
underneath as shown below.

Thread the cable through the following technic brick hole and pull it all the way out from the
middle. Connect the Bit Light cable to the 6-Port Expansion Board.