Lilin PZD6422CSE-2 User manual

Instruction Manual
Part Description & Dimensions
D/N 2MP HD PTZ DOME IP
CAMERA
For connecting D/N HD IP Camera series to the network, please follow one of the
system architectures:
(1). Use DC12V power adaptor and network switch connected to a network.
System Architectures
(3). Use PoE power injector and the network switch connected to the network.
PoE Switch
PC
LAN LAN / Internet
PoE Power Injector
PC
LAN LAN / Internet
AC
Non-PoE Switch
LAN
Installation
Bottom bracket
Upper cover
Transparent cover
Lens
RJ-45 Ethernet connector (supports PoE)
Power jack (DC12V ±10%)
Alarm In/Out connector
Micro SD card slot
Factory default button
PC
LAN LAN / Internet
Non-PoE Switch
DC12V Adaptor
(2). Use with PoE of the network switch connected to the network.
1. Retrieve the camera and remove the bottom bracket from the
upper cover with a hex key (FIG.1).
Use the included screws (M4.0x25) through the holes marked as
“a,” and fix the camera in the desired location (FIG.2 & FIG.3).
: The line group direction in the back.NOTE
Unit: mm
3.
connector to the RJ-45 connector and the DC-in connector and
Alarm in/out connector, respectively (FIG.4).
Attach the Ethernet and power cables and Alarm in/out jack
Connect the RJ-45 Ethernet cable with a waterproof connector
First, remove the waterproof connector and unscrew the
waterproof nut. Insert the Ethernet cable and connect to the
RJ-45 connector with proper tools (FIG.5). Then, tighten the
waterproof connector and nut before the RJ-45 connector is
connected to the camera (FIG.6).
FIG. 5 FIG. 6
4. Secure the upper cover to the bottom bracket with a hex key
(FIG.7).
16
57
106
120
24
21
22
23
28
2
9
2
9
120°
8°
φ108
Front
FIG. 3
FIG. 2FIG. 1
+5V
N.O.
COM
Alarm IN
GND
RED
WHT
GRN
ORG
BLK
SIREN
FIG. 4
FIG. 7
HD IP CAMERA
HD IP CAMERA
HD IP CAMERA
Network Cable
DC Power Input
Alarm In/Out
Connector
66-PZD6422CSE-2

Before accessing the IP camera, make sure that the camera's RJ-45 network,
audio, and power cables are properly connected. To set the IP address, consult
your network administrator for an available IP address. The default IP address for
each IP camera is 192.168.0.200. Users can use the default IP address for
verifying the camera's network connection.
Before Accessing IP Cameras
Universal ActiveX software components are required for web interface display of
JPEG or Full HD video. When you login to the IP camera by Internet Explorer,
the security warning dialog box will prompt the installation of the Universal ActiveX.
Click Install to download it.
Software Requirements
To configure an IP address using the IP scan tool. To change the settings of the IP
address, subnet mask, gateway, or HTTP port, you can follow the steps below:
1. Run the IPScan software.
2. Click Refresh. All available devices should be listed in the device list.
3. Select your device from the list provided.
4. Change the IP address, subnet mask, gateway, or HTTP port for the IP camera.
5. Click Apply to submit the settings.
6. Click Refresh to verify the settings.
Configuring IP Addresses with IPScan Software
To change an IP address via web interface, type the default IP address
(192.168.0.200) in the Internet browser and follow the steps below:
1. Login to the Full HD IP camera by the default username “admin” and default
password “pass”.
2. Click Basic Mode configuration hyperlink.
3. Click Network->General hyperlink.
4. Change the IP address, subnet mask, gateway, or HTTP port for the IP
camera.
5. Click Submit to verify the settings.
Configuring IP Addresses via Web Interface
Make sure your Internet browser allows the signed ActiveX plug-in to work on
your computer. Set “Download Signed ActiveX plug-in controls” to “Prompt”
and “Run ActiveX control and plug-in” to “Enable”. You can set this option via
Internet Explorer-> Tools-> Options-> Security Settings.
Internet Browser Settings & Application Required
Once complete, you can access the IP camera's live video by entering the
default IP address via your Internet browser. As the security warning dialog
box appears, click OK to download the ActiveX directly from the IP camera.
Login
The default usernames and passwords are as follows:
To logon the HD IP camera, please type username and password in logon
HTML page and click on Submit button to enter the system.
Username admin
Password pass
Administrator
To restore the hardware to factory default settings, please follow these steps:
1.Press and hold “RESET Key” for 10 seconds and release.
2.Wait for about 40 seconds, and the network LED light should turn off, and go
back on again.
3.The camera is now restored to factory default settings, and will reboot
automatically.
4.Search for the IP device using the IPScan software.
5.Start the IP device via an Internet browser.
6.Enter the default username “admin” and password “pass” to operate.
For your convenience, the IP address will revert to the default setting
of 192.168.0.200.
NOTE:
Emergency Factory Default
1. To avoid short circuit and electric shock, supply power only after the camera
cover gets fixed.
2. DO NOT use your hand to pan or to tilt the lens. Panning or tilting the lens will
break the motor of the camera.
3. DO NOT wall mount this camera. Wall mounting for the camera will scratch
the cover of the camera.
CAUTION