Link HD150 User manual

223 15th St. N.E.
Sioux Center, IA USA
51250-2120
www.linkmortuaryequipment.com
QUESTIONS?
CALL CUSTOMER
SERVICE
1-800-248-3057
The Link HD150 fits most hearses.
Estimated weight : 60 lbs.
Link Mortuary Equipment, a division of Link Mfg., Ltd.
www.linkmortuaryequipment.com 71340013
JULY 28, 2023
INSTALLATION
INSTRUCTIONS
HEARSE DECK HD150
(7134B001)

2
1. INTRODUCTION
Thank you for choosing a Link Mortuary Equipment HD150. We want to help you to get the best results from the deck and
to operate it safely. This manual contains information to introduce you to the Link HD150 and to assist you with its installa-
tion. The manual is intended solely for use with this product.
All information in this manual is based on the latest information available at the time of printing. Link Manufacturing re-
serves the right to change its products or manuals at any time without notice. Contact Link Mortuary Equipment at (800)
248-3057 for information on recent changes to products.
Damaged components should be returned to Link with a pre-arranged Returned Goods Authorization (RGA) number
through the Customer Service Department. The damaged component may then be replaced if in compliance with warranty
conditions.
Review the Parts List below to become familiar with the different components of the HD150.
Installation:
A. The HD150 sits in the hearse and is secured in place by inserting the supplied pin (either Ø1/2” or Ø3/8”
depending on the style of bier pin in the hearse) with the knob through the bier pin plate of the HD150 into
the bier pin plate of the hearse. The position of the deck will vary depending on which holes are used. It is
usually best to keep the deck as far back as possible while still being able to get the door closed.
B. A pair of Cot Post Tips has been included to replace the worn or missing tips from your cot. They will help
keep the sharp edges of the cot legs from damaging the surface of the HD150. To install these tips, simply
remove the old tips, insert the new tips, and lock them in place by tightening the screw on the bottom of the
tip.
Maintenance:
A. Clean with soap and water.
B. Call Link Mfg. at 1-800-248-3057 with any questions or comments.

3
LINK® MODEL “HD150” PARTS LIST
ITEM PART # DESCRIPTION QTY ITEM PART # DESCRIPTION QTY
115060011 SCREW-DRYWALL, 1 5/8" 12 11 144C0808 1/4 X 1 UNC TRUSS HD PH MACH SCR, SS 4
270000052 PIN-.50 X 3.00 112 14840800 1/4-20 X 9/16 TEE NUT W/PRONGS 4
370000053 PIN-.375 X 3.00 113 14840808 1/4-20 X 7/16 SLAB BASE WELD NUT 2
471340013 INSTRUCTIONS-INSTALLATION, HD150 114 14840P05 10-24 X 9/32 WELD IN T-NUT 2
571340021 STRIP-COT RESTRAINT 115 15060053 #10 -24 X 1.00, PHIL FLAT HEAD M.S. SS 2
671340026 BOARD-DECK, HD150 116 15070202 PLASTIC OVAL LEVER KNOB 2
771340028 MAT-BUMPER PROTECTION, HD150 117 15070289 BIER PIN PLATE 1
871340029 ANGLE GUARD-REAR, HD150 1- 15001150 TUBE-2.00 X 12.00, SNAP SEAL 1
971341101 FRAME-HEARSE DECK 1- 78000012 CPT-20 2
10 144C0806 1/4 X 3/4 UNC TRUSS HD PH MACH SCR, SS 2- 15001708 TUBING-POLY, CLEAR, 3 MIL, BULK, 36 8

223 15TH ST. NE, SIOUX CENTER, IA 51250
1-800-248-3057
www.linkmortuaryequipment.com