logitrans Logiflex Owner's manual

ZZZORJLWUDQVFRP
/2*,%22.
Supplement to Instructions Manual
Level control Logiflex

3
1.0Beforethefirstlift...
Safety instructions
The operator must stand so that he or she always has a full view of the lifting and
lowering movements of the equipment.
Clearances around the equipment must be checked before operating. No extrane-
ous objects must be placed under the equipment. MAKE SURE that neither fork
nor load snag extraneous objects during lifting and lowering.
Labels must be placed on the
Logiflex/Logilift
as shown here.
Warning label
SeealsotheLogiflex/Logilift
instruction manual.
If the operator does not have a full
viewoftheLogiflex/Logiliftand
its lifting and lowering move-
ments, barriers must be placed
around the area in which the
equipment operates.
A warning label with the below text must be attached to the Logiflex/ Logilift:
Black lettering on yellow background:

4
1
2
3
2.0 Operatingandfunctions
Thebrake mustbeactivated
beforetheequipment
can be used.
Push ON
Logiflex/Logiliftcanstart
lifting/lowering
Manualoperatingonthehandleis
notpossiblewhenlevelcontrolis
active

5
4
Up
Down
On/off
Greenlamp
for ON
Diode
Load: Unload:

6
}(-) (+)
-+
Max.3mm
+
-
0-10seconds’ delayof
lifting/loweringoperation.
550mm
Adjustmentof
functionrange.
3.0 Timedelay
Thefunctionrange isbetween 550mmand900 mm.
370mm
Functionrange
900mm max.height
4.0 Functionrange
1 2 3 . . . . . 10 sec.

7
+-
1000mm
+200mm -
30° 30°
0°
Thedetection rangeofthe pho-
tocellcan beadjusted upto
1000mmforwhite itemsand
800mmfor blackitems.The
shortestrange isapprox. 200
mmforwhiteitems.
Thephotocell canbeturned 30°
totheright orleft.
NOTE!The cell mustpoint
acrossthe pallet.
5.0 Photocell
Adjustmentofthedetectionrange
(ofthephotocell)

8
!
Discharged
<25% 25% 50% 100%
Final Charge
NB! Togetoptimumfunctionofthe
equipment,batterycharge
shouldnot bebelow 25%.
6.0 Batterycondition

9
7.0 Optionalsidemounting
Remove2 x 2screws
Refit2 x2 screws
2screws onthe controlbox
Changetheslide to
oppositehand
2screws on centretube

10
Min.100mm
8.0Adjustment
Adjustmentoftop andbottom
stopfor forks
UP=
Moves the top stop up or down.
Max.forkheight900mm.
DOWN=
Movesbottom stop upor down.
NOTE!
Overpressurevalvemust notbe
activated.
Afteradjusting:
NOTE!
Ifthedistance betweenpallet
andunderlay(or floor)is less
than100mm
(Euro-pallet):
Contactthe dealer!
NB! Beawareofdifferent
pallettypes
Adjustmentis necessaryifthe motordoes notstop beforethe top
positionandthe distancebetween palletand underlay(or floor)
islessthan 100mm.
Down
Up

11
9.0 Replacementoffuse
Examinethefuse.
Part number 986066 (ø5 X 20, 250V 4A T)

12
10.0 Fault location key
Afteracertain time,adjustmentscan benecessary.
BEFORECONTACTINGTHE DEALERFORHELP....
...TRYUSINGTHEFAULTLOCATIONKEY!
Symptomsandobservations:
SWITCHES:
Lampworks butnoreaction.
Thelamp doesnot workand theequipmentdoes notreact.
SLIDE:
Doesnot slideupand downwith the forks.
PHOTOCELL:
Doesnot react.
BATTERY:
Ifthebatteryis low, thelevel controlmight reactunpredictably and not
reactto thephotocell.
BRAKE:
Doesnot workorremain inthecorrect position.
A
B
C
D
E
F

13
A
B
C
D
E
F
9.0
5.0
5.0
6.0
6.0
2.0
Checkphotocellsetting
Checkbrake and brake switch
Checkfor cablefracture
Examinefuse.
Checkforobstructions
Checkspringtensioninslide
Adjustphotocellrange
Adjustphotocelldirection
acrosspallet
Checkconditionofbattery
Checkfordirt anduncleannesseson
thecentre tube
Contact
dealer
Cause Remedy
Chargebattery
Check that the pedal is
pressed as far down
as possible
Contact
dealer
Ifthe problemcannot be
solvedbyusingthefault
locationkey.....
.....please contactyour
distributor!

220506/02
S655 Pos-LLTE-ELF-EN
Periodic safety inspection
Safety inspection should be performed by the supplier or other qualified
persons at least once each year, unless local regulations state otherwise.
Such inspection shall be performed in accordance with the instruction
manual. Test instructions and test forms are available from the distributor.