LUCCI Air NEWHAVEN 216150 Owner's manual

V1.0-AU (05/2023)
LUCCI AIR
NEWHAVEN
DC CEILING FAN
⚫INSTALLATION
⚫OPERATION
⚫MAINTENANCE
⚫WARRANTY INFORMATION
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.

NEWHAVEN DC Fan Installation Instructions
1 | P a g e
THANK YOU FOR PURCHASING
Thank you for purchasing the latest in energy saving ceiling fans. This fan runs on DC (direct current) power
which gives it the benefit of being super energy efficient whilst still maintaining high volume air-movement and
silent operation.
Energy saving - The DC motor is the latest technology in fan design. Its highly efficient motor saves up to 65%
more energy than ceiling fans with traditional AC motors.
Silent operation –This DC fan motor is programmed with a stabilised current which efficiently reduces motor
noise.
Low operating temperature –The DC power is managed effectively which brings down the motor operating
temperature to less than 50℃. This results in a much cooler motor than a standard AC fan and increases the
longevity of the motor.
6 speed remote control - Regular AC ceiling fans usually come with only 3 speeds, this DC fan comes
complete with a 6 speed remote, which gives a greater choice of comfort levels.
SAFETY PRECAUTIONS
1. The appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning the use of the appliance by a person responsible for their safety.
2. Children should be supervised to ensure that they do not play with the appliance.
3. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local
wiring rules.
IN AUSTRALIA
WARNING:
FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION
MUST BE INCORPORATED INTO THE FIXED WIRING IN
ACCORDANCE WITH THE WIRING RULES.
As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting the minimum
electrical safety of this standard.
Please note warranty will be void if installation is without a means for an
all-pole disconnection incorporated in the fixed wiring in accordance with

NEWHAVEN DC Fan Installation Instructions
2 | P a g e
the wiring rules.
Example: If a fan is connected to a circuit that can be isolated via an
all-pole safety switch at the switchboard, then this is considered to be an
all-pole disconnection to the ceiling fan electrical circuit, meeting the
requirements of clause 7.12.2 of AS/NZS 60335.1.
A single-pole switch on the active of the receiver input of remote
control must also be included in the wiring, and located the same
room as the ceiling fan.
4. Do not dispose of electrical appliances, remote or batteries as unsorted municipal waste, use
separate collection facilities. Contact your local government for information regarding the collection
systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances
can leak into the ground water and get into the food chain, damaging your health and well-being.
5. The structure to which the fan is to be mounted must be capable of supporting a weight of 22 kg.
6. The fan should be mounted so that the blades are more than 2.1 m above the floor .
7. This fan is suitable for indoor use only. Mounting the fan in a location where it is subject to water or
moisture is dangerous and may increase the risk of damage, injury or electrical shock and will void the
warranty.
8. Must be assembled and installed by a licensed electrician.
9. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the ceiling
fan and contact the manufacturer, its service agent or suitably qualified persons.
10. The replacement of parts of the safety suspension system device shall be performed by the
manufacturer, its service agent or suitably qualified persons.
11. The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a
sufficient strength to withstand 4 times the weight of the ceiling fan; that the mounting of the suspension
system shall be performed by the manufacturer, its service agent or suitably qualified persons.
12. This remote contains battery that is non-replaceable.
13. The remote control can only be powered at a safe extra low voltage (DC 5 V).

NEWHAVEN DC Fan Installation Instructions
3 | P a g e
PARTS LIST
•Unpack your ceiling fan carefully. Remove all parts and hardware.
•Lay out all the components on a smooth surface and make sure there are no components missing before
assembling. If parts are missing, return the complete product to the place of purchase for inspection or
replacement.
•Check whether the ceiling fan has been damaged during transport. Do not operate/install any product
which appears damaged in any way. Return the complete product to the place of purchase for inspection,
repair or replacement.
•Examine all parts, you should have the following:
1.
Blades x 5 pcs
10.
Adaptor x 1
2.
Canopy x 1
11.
Bottom cover x 1
3.
Canopy cover x 1
12.
Mounting bracket x1
4.
Downrod and Ball Joint x 1
13.
Mounting bracket screws x2pcs
5.
Bolt and pin cover x 1
14.
Balance kit x1 set
6.
Fan assembly x1 set
15.
Blade screws x 11pcs
7
Light kit plate x1
16.
Blade Support Plates x5
8
GX53 lamp x 1
17.
Receiver x1set
9
Light kit extension cable x1pcs
(For use with extension down rod)
18.
Remote x1 set
Fig. 1

NEWHAVEN DC Fan Installation Instructions
4 | P a g e
INSTALLING THE FAN
TOOLS REQUIRED:
- Phillips / flat head screwdriver
- Pair of pliers
- Adjustable spanner
- Step ladder
- Wire cutter
- Wiring, supply cable as required by local provincial and national wiring codes and regulations
INSTALLING THE MOUNTING BRACKET
•The ceiling fan must be installed in a location so that the blades are spaced 300mm from the tip of the
blade to the nearest objects or walls.
•Install the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least 22kg,
with two long screws provided. Ensure at least 30mm of the screw is threaded into the support. (Fig. 2)
NOTE: The bracket screws provided are for use with wooden structures only. For structures other
than wood, the appropriate screw type MUST be used. Ensure the screws used are suitable for the
mounting surface and the surrounding environment.
ANGLED CEILING INSTALLATION
This fan hanging system supports a maximum 10 degree angled ceiling installation. (Fig. 3)
Fig. 3
Fig. 2
10°
22 KG

NEWHAVEN DC Fan Installation Instructions
5 | P a g e
INSTALLING THE DOWN ROD (Fig. 4)
1. Remove the ball joint (2) and dowel pin (3) by loosening the set screws (4) from the down rod (6). Remove
the hitch pin (9) by removing the lock clip (10) (Fig. 4.1). NOTE: Do not discard keep these parts, they
are required to reassemble later.
2. Loosen the set screws (11) on the down rod coupling housing (8). (Fig. 4.2)
3. Carefully feed the fan wires (1) up through the down rod (6). (Fig. 4.3)
4. Assemble the down rod (6) into the down rod coupling housing (8), by inserting and line up the down rod
coupling housing holes with the down rod holes and insert the hitch pin (9) and secure with the lock clip (10).
(Fig. 4.3)
5. Secure the down rod (6) by tightening the set screws (11). (Fig. 4.4)
Fig. 4.1
Fig. 4.2

NEWHAVEN DC Fan Installation Instructions
6 | P a g e
6. Insert the decorative cover (7) onto the down rod (6) to cover the down rod coupling housing (8).(Fig. 4.5)
7. Insert the canopy cover (12) & canopy (5) over the down rod (6) and install the ball joint (2) and dowel pin
(3) back onto the down rod (6) and secure by tightening the set screws (4). (Fig. 4.5& Fig.4.6)
Fig. 4.6
Fig. 4.3
Fig. 4.4
Fig. 4.5

NEWHAVEN DC Fan Installation Instructions
7 | P a g e
HANGING THE FAN
Lift the fan assembly onto the mounting bracket. Ensure the registration slot (A) of the hanger ball is
positioned on the stopper (B) of the mounting bracket (C) to prevent the fan from rotating when in operation.
(Fig.5)
INSTALLATION OF BLADE (Fig. 6)
1. Orientate the blade Support plate and fan blade onto the fan assembly (Fig.6)
Mount the fan blade onto the fan assembly using two blade screws with lockwashers (supplied in fan
parts bag) (Fig.6).
Ensure all screws are tightened evenly to reduce the chance of warping or unbalancing.
Take care not to over tighten the screws, as this can damage the blades
Take note the correct side of the blades with the marking “THIS SIDE UP” faces the ceiling.
2. Repeat for the remaining four fan blades and support plates.
To secure the five blade support plates and the fan blades to the fan assembly, tighten all screws with
lockwashers.
Fig. 5
Fig. 6

NEWHAVEN DC Fan Installation Instructions
8 | P a g e
INSTALLATION OF LIGHT KIT (Fig. 7)
NOTE: The light kit must be installed by a licensed electrician.
1. Loosen the screw (1) from the fan bracket. (Fig. 7)
2. Align the two slot screws with the keyhole slots (2) of the light kit plate. (Fig. 7)
3. Turn the light kit plate counterclockwise until the slot screws are firmly at the end of the slots (2).
4. Secure screw (1) to the light kit plate. Tighten all three screws. Do not over-tighten.
INSTALLATION OF LAMP (Fig. 8)
• Install the lamp on the fan assembly then secure it by turning clockwise. (Fig. 8)
Fig. 8
Fig. 7

NEWHAVEN DC Fan Installation Instructions
9 | P a g e
INSTALLATION OF BOTTOM COVER (Fig. 9 & Fig.10)
If no lamp is required
1. remove the light kit plate from the fan bracket .
2. Orientate the adapter onto the fan bracket, mount the adapter onto the fan bracket using three screws
Tighten all three screws. Do not over-tighten. (Fig.9)
5. Install the bottom cover to the adapter then secure it by turning clockwise. (Fig.10)
Fig. 9
Fig. 10