LUCCI Air Altitude Eco Led Service manual

ALTITUDE ECO LED - V1.0 –WS-MUTIL
CEILING FAN MANUAL
INSTALLATION
OPERATION
MAINTENANCE
WARRANTY INFORMATION
LUCCI
ALTITUDE ECO LED
CEILING FANS
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.

2
GB
Installation Instruction Manual .......................................................................................... 3
D
Installationsanleitung ........................................................................................................13
F
Guide d’installation............................................................................................................23
E
Manual de instrucciones de instalación.............................................................................33
I
Manuale delle istruzioni di installazione............................................................................43
NL
Installatiehandleiding.........................................................................................................53
CONTENTS

3
Congratulations on purchasing this quality Lucci product. To ensure correct function and
safety, please read and save all instructions carefully before using the product.
The information contained in the following pages has been prepared to ensure you of
trouble-free operation of your Ceiling Fan .
1. This appliance is NOT intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
2. The all-poles disconnection must be incorporated in the fixed wiring in accordance with
local wiring rules.
3. Do not dispose of electrical appliances as unsorted municipal waste, use separate
collection facilities. Contact your local government for information regarding the collection
systems available. If electrical appliances are disposed of in landfills or dumps, hazardous
substances can leak into the groundwater and get into the food chain, damaging your
health and well-being.
4. The structure to which the fan is to be mounted must be capable of supporting a weight of
40kg.
5. The fan should be mounted so that the blades are at least 2.3 meters above the floor in
Europe
6. The fan should be mounted so that the blades are at least 2.1 meters above the floor in
Australia
7. The fan is designed for indoor use only. Mounting the fan in a situation where it is subject
to water or moisture is dangerous.
8. Only an authorized electrician should execute the installation.
CONGRATULATIONS ON YOUR PURCHASE
SAFETY PRECAUTIONS

4
Unpack the fan and carefully identify the parts. Please refer to Fig 1.
1
Hanger bracket x 1
2
LED driver x 1
3
Pre-assembled fan motor, down rod and canopy cover x 1
4
LED light kit x 1
5
Blades x 4
6
Screw for hanger bracket x 2
7
Flat washer x 2
8
Spring washer x 2
9
Wall plugs for Screw x 2
10
Balancing kits x 1 set
11
Motor screws for blades x 13
12
Wall controller x 1 set
BEFORE INSTALLATION
Fig. 1

5
The ceiling fan must be installed in a location so that the blades are 300mm spacing from the tip of
the blade to the nearest objects or walls.
Secure the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at
least 40KG, with two long screws provided. Ensure at least 30mm of the screw is threaded into the
support.
NOTE: The bracket screws provided are for use with wooden structures only. For structures
other than wood, the appropriate screw type MUST be used.
Angled Ceiling Installation
This fan hanging system supports a maximum 20
degree angled ceiling installation.
INSTALLING THE MOUNTING BRACKET
Fig. 2
Fig. 3

6
1. Carefully lift the fan and place the down rod ball assembly into the spacing allocated in the mounting bracket and lock
the ball into place. And then insert the LED driver into the mounting bracket. Fig. 4
Fig.4
2. Refer to the wiring diagram provided for Electrical Connection/installation. Fig. 9 & 10
WARNING: To prevent electrical shock or risk of fire, do not attempt to perform the electrical connection wiring
yourself. All Electrical connections must be carried out by a qualified Licensed Electrician.
NOTE: An additional all pole disconnection switch must be included in the fixed wiring.
3. After completing the electrical wiring at the mounting bracket terminal and connecting the fan motor and fixed wiring via
the 4-ports quick connectors (1); connecting the LED driver input wires and fixed wiring via the 3-ports quick connectors
(2); also connecting the LED driver output wires and LED light wires via the 2-ports quick connectors (3). Fig.5
Cover the mounting bracket with the canopy cover. Ensure all electrical wirings are tucked inside the canopy and that
they are not damaged during this step, and secure with screws. Fig. 6
Fig.5
INSTALLING THE FAN
LED Driver

7
4. Finally secure the canopy cover to canopy screws via turn it clockwise. Fig. 6
Fig.6
5. Insert the blades through the side slot of the motor and align with the 3 holes. If the holes do not align, the blade is
upside down. The blade should fit securely and the screws should slot into the blade screw holes.
Insert the screw driver with screw through the key hole of lamp bracket. Secure the blades with 3 blade screws, and
ensure that the 3 blade screws are tightened at the same time. Ensure all screws are tightened evenly to reduce
chance of warping or unbalancing. Repeat this process for all blades. Fig.7
Fig.7
6. Lift up the LED light kit to the lamp base and connect the LED power wires to the LED light kit via the quick connectors.
Then press the housing assembly screws into the big ends of keyhole slots, and turn the LED light kit body clockwise
until the housing assembly screws are firmly situated in the narrow ends of the keyhole slots. Fig.8

8
Fig.8
WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY
A LICENSED ELECTRICIAN.
NOTE: AN ADDITIONAL ALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE
FIXED WIRING.
NOTE: Wiring diagram includes the light kit wiring. The light wiring diagram and switch is
omitted when no light kit is use with the ceiling fan.
ELECTRICAL WIRING DIAGRAM
INSTALLING THE FAN
Fig. 9

9
Rotary switch and capacitor wiring diagram.
FAN WALL CONTROL
Your ceiling fan is controlled via the rotary switch (fan) and rocker switch (light) via the wall controller. Refer to
below figures:
SWITCH POSITION
(ARROW POINTING)
DESCRIPTION
OFF – FAN IS OFF
1 – FAN IS “ON”, SPEED = HIGH
2 – FAN IS “ON”, SPEED = MEDIUM
3 – FAN IS “ON”, SPEED = LOW
LIGHT SWITCH – Toggle to switch ON/OFF the light
USING YOUR CEILING FAN
Fig. 9

10
WALL CONTROLLER
REVERSING SWITCH
Your ceiling can operate either summer or winter mode.
SUMMER Mode: The reverse switch shall be in the “down” (SUMMER) position to make the fan
rotate in an anticlockwise direction. The airflow will be directed downwards, for cooling in summer.
WINTER Mode: The reverse switch shall be in the “up” (WINTER) position to make the fan rotate in a
clockwise direction. The airflow will be directed upwards assisting in the circulation of warm air, for
energy conservation in winter.
Reverse Switch
Fig. 10
Fig. 11

11
WOBBLE:
NOTE: CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY
ARE MOUNTED ON A RUBBER GROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE
CEILING IT WOULD CAUSE EXCESSIVE VIBRATION. MOVEMENT OF A FEW CENTIMETRES IS
QUITE ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEM.
TO REDUCE THE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH FIX THE
MOUNTING BRACKET AND DOWN ROD ARE SECURE.
BALANCING KIT: A balancing kit is provided to balance the ceiling fan on initial installation. Please
refer to the instruction on how to use the balancing kit. The balancing kit can be used to assist
re-balancing should the ceiling fan become un-balanced again. Store your balancing kit away after
installation for future use if required.
NOISE:
When it is quiet (especially at night) you may hear occasional small noises. Slight power fluctuations
and frequency signals superimposed in the electricity for off-peak hot water control, may cause a
change in fan motor noise. This is normal. Please allow a 24-hour “breaking -in” period, most noises
associated with a new fan disappear during the time. The manufacturer’s warranty covers actual faults
that may develop and NOT minor complaints such as hearing the motor run –All electric motors are
audible to some extent.
CARE AND CLEANING
Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free
cloth to avoid scratching the paint finish. Please turn off electricity power when you do so.
Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and
create the possibility of an electrical shock.
The motor has a permanently lubricated ball bearing. There is no need to oil
NOTE: Always turn off the power at the mains switch before attempting to clean your fan.
ALTITUDE ECO SERIES
models
Rated
Voltage
Rated power
(motor)
Rated power
lamp
Lamp type
LD-48-LED
(48 inch blade fan only)
220-240
VAC
60W
17W,LED Life
time: 30,000H
LED light kit with Driver
Driver Model No.: TD0151N-E052
LD-52-LED
(52 inch blade fan only)
220-240
VAC
70W
17W, LED Life
time: 30,000H
LED light kit with Driver
Driver Model No.: TD0151N-E052
TECHNICAL INFORMATION
AFTER INSTALLATION

12
IN AUSTRALIA / NEW ZEALAND CUSTOMER – Please refer to the separated WARRANTY
STATEMENT.
IN EUROPE – If you are a European Customer Please contact the retail outlet where the fan was
purchase for warranty service.
WARRANTY INFORMATION

13
Wir gratulieren zum Kauf dieses Qualitätsproduktes von Lucci. Bitte lesen Sie die
Sicherheitshinweise vollständig und sorgfältig durch, um den ordnungsgemäßen und sicheren
Einsatz des Gerätes zu gewährleisten.
Die Hinweise auf den nachfolgenden Seiten erklären den sicheren und störungsfreien Betrieb
Ihres Deckenventilators.
1. Dieses Gerät ist NICHT für den Gebrauch durch Personen (einschließlich Kinder) geeignet,
die über eingeschränkte körperliche, sensorische oder mentale Fähigkeiten oder über
mangelnde Erfahrung und Kenntnisse verfügen, es sei denn, ihr Gebrauch des Gerätes
wird durch eine Person, die für deren Sicherheit verantwortlich ist, entsprechend
beaufsichtigt oder angeleitet.
2. Laut Schutzvorschrift muss bei der Festverdrahtung die allpolige Trennung verwendet
werden.
3. Bedeutung des durchgestrichenen Müllbehälters auf Rollen: Geben Sie elektrische Geräte
nicht in den Hausmüll (Restmüll), sondern achten Sie auf umweltgerechte Entsorgung.
Falls Sie sich hierzu nicht sicher sind, erkundigen Sie sich bei Ihrer örtlichen Behörde nach
den sachgerechten Entsorgungsmöglichkeiten. Elektrische Geräte, die auf eine Müllhalde
geworfen werden, können Gefahrstoffe in das Grundwasser abgeben, die in die
Nahrungskette gelangen und dadurch gesundheitsschädlich sind.
4. Die Decke, an die dieser Ventilator befestigt werden soll, muss ein Gewicht von 40 kg
tragen können.
5. In Europa sollte der Ventilator so an der Decke befestigt werden, dass sich die
Ventilatorflügel mindestens 2,3m über dem Boden befinden.
6. In Australien sollte der Ventilator so an der Decke befestigt werden, dass sich die
Ventilatorflügel mindestens 2,1m über dem Boden befinden.
7. Der Ventilator ist ausschließlich für die Verwendung im Innenbereich konstruiert. Es ist
gefährlich, den Ventilator in Umgebungen zu installieren, in denen er Wasser oder
Feuchtigkeit ausgesetzt ist.
8. Die Installation sollte nur von einem befugten Elektriker vorgenommen werden.
WIR GRATULIEREN ZUM KAUF DIESES GERÄTES
SICHERHEITSHINWEISE

14
Bitte packen Sie das Gerät aus, und stellen Sie sicher, dass alle Teile im Versandkarton enthalten sind.
Bitte beachten Sie Abb. 1.
1
Hanger bracket x 1
2
LED driver x 1
3
Pre-assembled fan motor, down rod and canopy cover x 1
4
LED light kit x 1
5
Blades x 4
6
Screw for hanger bracket x 2
7
Flat washer x 2
8
Spring washer x 2
9
Wall plugs for Screw x 2
10
Balancing kits x 1 set
11
Motor screws for blades x 13
12
Wall controller x 1 set
VOR DER INSTALLATION ZU BEACHTEN
Abb. 1

15
Der Deckenventilator muss an einem Ort so installiert werden, dass die Spitzen der
Ventilatorflügel mindestens 300mm vom nächsten Gegenstand oder der Wand entfernt sind.
Befestigen Sie die Deckenhalterung nur an Decken oder Deckenverschalungen und anderen
Deckenstrukturen, die ein Gewicht von mindestens 40KG sicher halten können; verwenden Sie
dazu die zwei langen Schrauben, die mit dem Ventilator ausgeliefert wurden. Stellen Sie sicher,
dass die Schraubengewinde mindestens 30mm in das Material eingedreht sind, woran die
Halterung für den Ventilator befestigt ist.
HINWEIS: Die mitgelieferten Halteschrauben sind nur für Tragestrukturen aus Holz geeignet.
Für Tragestrukturen die nicht aus Holz sind, MUSS der dafür geeignete und zugelassene
Schraubentyp verwendet werden.
Installation an geneigten Decken
Dieses Halterungssystem ist nur für die Aufhängung an
geneigten Decken mit einem Neigungswinkel von bis
zu 20geeignet.
INSTALLATION DER DECKENHALTERUNG
Abb. 2
Abb. 3

16
1. Carefully lift the fan and place the down rod ball assembly into the spacing allocated in the mounting bracket and lock the
ball into place. And then insert the LED driver into the mounting bracket. Fig. 4
Fig.4
2. Refer to the wiring diagram provided for Electrical Connection/installation. Fig. 9 & 10
WARNING: To prevent electrical shock or risk of fire, do not attempt to perform the electrical connection wiring
yourself. All Electrical connections must be carried out by a qualified Licensed Electrician.
NOTE: An additional all pole disconnection switch must be included in the fixed wiring.
3. After completing the electrical wiring at the mounting bracket terminal and connecting the fan motor and fixed wiring via
the 4-ports quick connectors (1); connecting the LED driver input wires and fixed wiring via the 3-ports quick connectors
(2); also connecting the LED driver output wires and LED light wires via the 2-ports quick connectors (3). Fig.5
Cover the mounting bracket with the canopy cover. Ensure all electrical wirings are tucked inside the canopy and that
they are not damaged during this step, and secure with screws. Fig. 6
Fig.5
INSTALLING THE FAN
LED Driver

17
4. Finally secure the canopy cover to canopy screws via turn it clockwise. Fig. 6
Fig.6
5. Insert the blades through the side slot of the motor and align with the 3 holes. If the holes do not align, the blade is upside
down. The blade should fit securely and the screws should slot into the blade screw holes.
Insert the screw driver with screw through the key hole of lamp bracket. Secure the blades with 3 blade screws, and
ensure that the 3 blade screws are tightened at the same time. Ensure all screws are tightened evenly to reduce
chance of warping or unbalancing. Repeat this process for all blades. Fig.7
Fig.7
6. Lift up the LED light kit to the lamp base and connect the LED power wires to the LED light kit via the quick connectors.
Then press the housing assembly screws into the big ends of keyhole slots, and turn the LED light kit body clockwise
until the housing assembly screws are firmly situated in the narrow ends of the keyhole slots. Fig.8

18
Fig.8
WARNHINWEIS: IM INTERESSE IHRER PERSÖNLICHEN SICHERHEIT MÜSSEN ALLE
ELEKTRISCHEN ANSCHÜSSE VON EINEM ZUGELASSENEN ELEKTRIKER AUSGEFÜHRT
WERDEN.
HINWEIS: EIN ZUSÄTZLICHER, ALLPOLIGER TRENNSCHATER MUSS IN DER INSTALLATION
DER WANDVERKABELUNG ENTHALTEN SEIN.
HINWEIS: Das Verkabelungsdiagramm zeigt die Verschaltung des Kabelsatzes für die den
Schalter und das Licht. Das Verkabelungsdiagramm für das Licht und den Schalter werden
nicht dargestellt, wenn Ihr Deckenventilator nicht mit einer Lampe ausgerüstet ist.
ELEKTRISCHE VERSCHALTUNG - DIAGRAMM
INSTALLING THE FAN
Abb. 9

19
Verschaltungsdiagramm für Drehschalter und Regelungskondensator.
VENTILATOR WANDREGLER
Sie können die Geschwindigkeit Ihres Deckenventilators über den Drehschalter (Ventilator) regeln, und das Licht
mittels des Kippschalters (Licht) ein- und ausschalten. Beachten Sie die nachfolgende Abbildung:
SCHALTERSTELLUNG
(PFEILRICHTUNG)
BESCHREIBUNG
AUS – VENTILATOR IST AUS
1 – VENTILATOR IST “EIN”, GESCHWINDIGKEIT = HOCH
2 – VENTILATOR IST “EIN”, GESCHWINDIGKEIT = MITTEL
3 – VENTILATOR IST “EIN”, GESCHWINDIGKEIT = NIEDRIG
LICHTSCHALTER – Betätigen, um Licht EIN/AUS zu schalten.
WANDREGLER
DER EINSATZ DES DECKENVENTILATORS
Abb. 10

20
RÜCKLAUFFUNKTION
Der Ventilator kann sowohl im Vorlauf als auch im Rücklauf betrieben werden.
SOMMERBETRIEB: Wenn der Schalter für die Rücklauffunktion auf “down” (SOMMER) steht, dreht
der Ventilator sich gegen den Uhrzeigersinn. Die Luftbewegung wird nach unten gelenkt und bringt im
Sommer den gewünschten Abkühlungseffekt.
WINTERBETRIEB: Wenn der Schalter für die Rücklauffunktion auf “up” (WINTER) steht, dreht sich
der Ventilator im Uhrzeigersinn. Die Luftbewegung wird nach oben gelenkt, um im Winter Energie zu
sparen.
Reverse Switch
Abb. 11
Fig. 12