Lunos EAU 100 User manual

Mounting Instructions
Exhaust Air Unit EAU 100
- Please pass on to User-
Contents Page:
About these instructions, Safety instructions, Technical data, Disposal 1
Dimension drawings, Scope of application, Shipping units 2
Assembly: Assembly tube, Outer grille 3
Assembly: Electrical installation and Electrical connection 4
Assembly: Exhaust Air Unit and Interior Screen 4
Filter change 4
About these Instructions
 Read these instructions carefully and completely before executing assembly work! General safety instructions
and the safety symbols with respective notes in text form must be observed.
 These instructions are to be passed on to the user after completing assembly work (tenant, owner, building
administration etc.).
Symbols in these instructions
This symbol warns of a risk of injury.
This symbol warns of a risk of injury from electricity
Safety Instructions
Caution! All terminals must be completely disconnected from the power supply before commencing
assembly work! The fan is insulated pursuant to Protection Class II, connection protection does not apply!
Attention! Electrical connections must be carried out by authorized qualified staff in accordance with
applicable VDE 0100!
Attention! This device must not be operated by children or persons (filter change/cleaning) who are
not able to operate it safely on account of their physical, sensory or mental capacity or due to their inexperi-
ence or lack of skills. Children must be supervised to ensure they do not play with the device.
Technical Data
Supply voltage: 220-230 VAC 50/60 Hz
Protection Class: IP X2
max. flow rate: 100m³/h
max. pressure difference: 34 Pa
power consumption: 15 W
Disposal
Dispose of packaging correctly sorted. If you wish to dispose of the device, observe applicable conditions.
Your local disposal center will provide relevant information.
1

Dimension drawing (all dimensions in mm)
2
□136 34 min. 140 14
15 98
Ø115
Assembly tube DI 100 mm,
DA 104 mm
Dimensions in mm
Scope of application
Temperature range: - 15°C to + 40°C
Can be used at a relative humidity of up to 65% inside the apartment. Low condensate formation may occur during
the heating period. If limits are exceeded, switch off the device and close the interior screen. Ensure supply of fresh
air by opening the window.
Shipment units
Check the delivery with regard to completeness and perfect condition!
Tube DI 100 mm
Plaster protective cover
Filter
Cover
frame
Assembly tube Inner screen
Design
screen
EAU 100 build-in device Outer grille

Other outer grilles available on request!
Assembly - Assembly Tube and Outer Grille
Prepare wall cavities for the assembly
tube (via core bore hole, drill bit Ø106
mm). If necessary, shorten the tube to
the required installation length. Make
sure there is a protrusion of the tube on
both sides to bridge the plaster thick-
ness (after plastering, the tube must be
flush with the plaster). Insert the tube
and seal it all round (Assembly adhe-
sive Order No. 038 733).
Apply the inside and outside plaster. In
the case of an outside closure to be
plastered, first replace the plaster pro-
tective cover with the outside closure.
Remove the outside plaster protective
cover. Mount the outer grille using the
integrated claws (tighten the screws).
The solid plastic outside covers provid-
ed by Lunos ensure high resistance to
driving rain and can be used in the
Stress Group III pursuant to DIN 4108-
3 (2012-04). Metal or metal-coated
covers can be used in Stress Group I
pursuant to DIN 4108-3 (2012-04).
In the case of buildings exposed to
wind or the risk of strong winds and
rain to the outside covers, further
measures of weather protection may be
required.
3
inside
inside outside
outside
Plaster protective
Tighten the claws with screws
3 mm

Assembly - Electrical Installation and Electrical Connection
Caution! All assembly work on the fan must only be carried out
when power has been disconnected from all terminals!
Make sure all connection lines are de-energized before connect-
ing the fan to the power supply !(disconnection from power supply
with at least 3 mm contact opening, e.g. all-pole circuit-breaker)
Each circuit connected to the ventilation system must be fitted
with residual current protection (e.g. a RCD switch)! Electrical
connections must be carried out by qualified staff only!
Additional installations and electrical components in this ventila-
tion system are not admissible!!
Safety Instructions
4
Assembly - Exhaust air unit and interior screen
Insert inside closure with filter, snap the
design screen in in the Open position!
Finished!
„Open position“
„Closed position“
Catch lock
Fixing pin
Design screen
- Catch locks snapped in
- Fixing pins in front of
cover frame
- Design screen turned 180°
compared to Open position.
- Fixing pins sunk into the
bore holes of the cover
frame.
15 mm
E 349 05.19
Filter Change and Cleaning
The EAU 100 has no filter change indicator. We recommend to look every 3 month at the condition of the filter. If
it’s polluted, it should be replaced or cleaned. Therefor remove the design screen, remove the filter, install the new
or cleaned filter (cleaning of the filter can be executed e.g. in the dishwasher), put the design screen back on.
Wipe the design screen and cover frame with a dry, soft cloth when required.
Filter change and cleaning must not be carried out by children and persons not able to execute such work
due to their physical, sensory or mental capacity, or due to their inexperience or lack of skills.
LUNOS Germany
LUNOS Lüftungstechnik GmbH Phone [phone]
für Raumluftsysteme Fax [phone]
Wilhelmstr. 31 [email protected]
13593 Berlin ∙ Germany www.lunos.de