Luvion Digital Audio Baby Monitor User manual

Digital Audio Baby Monitor
User’s Manual
Manuel d'utilisation
Benutzerhandbuch
Manual del Usuario
Manuale utente

1
Legend of functions
Parent unit
Baby unit
What you get
What else you need
Important information
Setting up
Set up the baby unit
Power supply
Set up the parent unit
Power supply
Belt clip
Check the connection
Using the baby monitor
Adjust volume
Mute function
Talk back
Night light
Sound level indicator lights
Troubleshooting
Frequently asked questions
Technical specifications
Care and maintenance
2
4
2
3
4
5
7
7
7
9
9
11
11
12
12
13
13
14
14
15
16
16
16
Contents

2
Legend of functions
1
2
3
4
5
11
12
10
Mute button
Link / Unlink indicator LED
Talk back button
Sound level light
Volume / VOX sensitivity control
Power / charging
indicator LED
7
8
9
ON/OFF button
Belt clip
Battery compartment
Parent unit charger
Charger light
Power adapter jack
for the charger
+_
6
1
7
2
3
4 5
8
9
11
12
10
6
Link Power
Link Power
A, Parent unit Fig. 1

3
Legend of functions
1
2
3
4
5
Link / Unlink indicator LED
Night light
Night light ON/OFF button
Volume control
Power / Battery low indicator LED
+_
ON/OFF button
7
8
9
Power adapter jack
Battery compartment cover lock
Battery compartment
6
1
2
3
4
5
6
7
9
8
B, Baby unit Fig. 2

4
What you get
Baby unit
Baby unit mains power adapter
Parent unit
Parent unit mains power adapter
2 x AAA rechargeable batteries for the parent unit
Parent unit charger
Belt clip for the parent unit
This user’s manual
What else you need
4 x AA non rechargeable batteries (Alkaline
recommended) batteries for the baby unit (not
supplied).

5
Important information
Please read this user’s manual carefully be-
fore using your baby monitor and keep it for
future reference. This baby monitor is
designed as an aid and should not be used
as a substitute for responsible and proper adult
supervision.
1 M/ 3 feet
Make sure the baby unit and adapter cable
are always out of reach of the baby (at least 1
meter / 3 feet away).
Never place the baby unit inside the baby’s
bed, cot or playpen.
Never cover the baby monitor (e.g. with
clothes, towels or blankets).
Never place or use the baby monitor at moist
places or close to water.

6
If travelling abroad, make sure that the voltage
shown on the mains power adapter corresponds
to the local mains power before connection to
the power supply.
Important information
To prevent electric shock, do not open the case
of the baby unit and the parent unit (except bat-
tery compartment covers).
Risk of explosion if batteries are replaced by an
incorrect type. For the parent unit, always use
rechargeable batteries.
2 x AAA rechargeable batteries for the parent unit.
no rechargeable batteries

7
Setting up
1. Set up the baby unit
1.1 Power supply
The baby unit uses either four AA Alkaline
batteries or household AC current.
Warning: Use only the mains power adapter supplied. Use an improper adapter may
permanently damage the baby unit.
ON/OFF
Mains operation
1. Plug the mains power cable into
the socket on the side of the baby unit.
2. Connect the other end to the mains power.
OK
3. Once the mains connection is done, the
Power Indicator LED will light up in green.

8
Setting up
Battery operation
OR
The baby unit also works on battery power,
so that you can use it even when you are
away from a mains power socket or during
a power cut.
1. Remove the battery compartment cover and insert 4 x AA Alkaline batteries
into the battery compartment on the baby unit, then close the battery
compartment cover.
2. Turn on the baby unit, the power Indicator LED will light up
in green.
OK
Note1: The recommended batteries are 4 x AA Alkaline.
2: The baby unit will only work from the batteries if the mains power is
disconnected.
3: Battery low: The power indicator LED on baby unit will start blinking and the link
indicator LED on the parent unit will flash in red.
4: Please power off the baby unit before removing the mains power or the batteries.

9
Setting up
2 x AAA rechargeable batteries for parent unit
2. Set up the parent unit
2.1 Power supply
Battery operation
1. Remove the battery compartment cover and insert 2 x AAA
rechargeable batteries into the battery compartment, then close
the battery compartment cover as shown.
Warning:
The parent unit uses 2 x AAA
rechargeable batteries.
Never use non-rechargeable batteries on the parent unit. Use only the recommended type
2 x AAA rechargeable batteries – using other types of batteries could permanently
damage your unit.
2. Place the parent unit on the charge and plug the power adapter into
the wall socket.
OK
1 2
3 4
You should always ensure you have inserted
batteries in the parent unit.

10
Setting up
Warning : Use only the mains power adapter supplied. Using an inproper
adapter may permanently damage the charger.
3.When the battery power is low, power / charging indicator LED on the parent
unit will blink in green. When the unit is OFF and the charging starts, you will
hear “beep beep” and the LED will blink in orange, the LED light will be off
when the batteries are fully recharged.
When the unit is ON and the charging starts, you will hear “beep beep” and
the LED will blink in green and orange, the LED light will stay green when the
batteries are fully recharged.
Mute
Note1: Charge the parent unit for at least 8 hours before using the baby monitor for the first time.
2: C harging or battery replacement is necessary if the following occurs:
The power indicator LED does not light up in orange.
Battery low: The power indicator LED blinks.
3: The parent unit can still be used while recharging.
4: Please power off the parent unit before removing the batteries.
5: If the batteries of the parent unit is not to be used for a long time, remove the batteries
from your parent unit and store them in a dry ,cool place.
2: Insert the rechargeable batteries before charging the parent unit.
Note 1: Even the parent unit is not placed on the charger, the charger light
would always light up in red.
4.The charging stand will keep the Parent Unit batteries at the fully charged
status. When the Parent Unit is placed on the stand while the power is turned
on, the Charging LED light may be constantly on.
3: When the parent unit which does not contain, rechargeable batteries is plug
into the charger, the parent unit will turn on the power about 3-5 seconds
and then power off .
4: If your rechargeable batteries get totally discharged, you need to recharge them
for at least fifteen minutes, and the parent unit will turn on the power about 3-5
seconds and then power off continuously before you can turn it back on.
5: When the parent unit is charging, please turn on the baby unit.

11
Setting up
2.2 Belt clip
You can use the belt clip to carry the parent unit on the belt.
You can use the belt clip to carry the parent unit on the belt.
3. Check the connection
When both units are switched on, the green link indicator lights on both units
will be on. If the link between the units is broken, the link lights on both units
will turn red, and the parent unit ,will sound alarm to signal that there is no
communication between the units. If this happens:
link
t
h
e
g
r
e
e
n
l
i
n
k
l
i
g
h
t
s
o
n
b
o
t
h
U
n
i
t
s
w
i
l
l
c
o
m
e
o
n
.
link
t
h
e
l
i
n
k
l
i
g
h
t
s
o
n
b
o
t
h
U
n
i
t
s
w
i
l
l
t
u
r
n
r
e
d
.
link
link
link
Note: In the event of power
failure, when the power
is restored all your settings
will remain unchanged.
Check that the mains power is plugged in and switched on at the baby unit.
Check that the units are within range of one another.
Check the batteries are proper installed.

12
Using the baby monitor
Position both units in the same room to test the
connection. Make sure the baby unit is at least
1 meter / 3 feet away from the parent unit.
1 M/ 3 feet
Be
B
e
Be
1 M/ 3 feet
Note: If you put the parent and baby units too close you will hear a high pitched
noise, this is normal. The units are designed to be located at a distance
from one an other, e.g. in different rooms.
1. Adjust volume
At the parent or baby unit:
There are 5 volume levels on each unit.
Press +to increase or –to decrease the volume. Changing the
volume setting on the baby unit affects the volume when you use the
Talk back feature.
Note: You can press and hold the +or –buttons, the volume will increase /
decrease automatically.

13
Talk
Talk
2. Mute mode and microphone sensitivity level setting
Press Mute button on the parent unit, then press +or – within 3
seconds to select the sensitivity level required- level 1 for Low sensitivity,
or level 5 for High sensitivity (Default setting is level 3).
3. Talk back
You can use the Talk back feature to comfort and reassure your baby.
Press and hold Talk on the parent unit to speak to the baby.
Release Talk to hear your baby again.
Using the baby monitor
To set the sensitivity level, follow these steps:
or level 5 for High sensitivity (Default setting is level 3).
Note1: You can press and hold the +or –buttons, the sensitivity levels will be
changed automatically
Note3: Press the Mute button again to return to normal mode.
Note2: The level 4 LED indicator will light up when getting into Mute mode.

14
Using the baby monitor
4. Night light
The night light provides a soft and comforting glow for your baby and allows
you to check on the baby without having to turn on the main room light.
Press the Light button on the baby unit. Press again to switch it off.
Light
5. Sound level lights
The sound level lights are the green and red lights locate at the top of the
Parent unit which illuminate according to the level of sound in the baby’s
room.
There are 8 sound levels:
Level 0: 0 green light
Level 1: 1 green light
Level 2: 2 green lights
Level 3: 3 green lights
Level 4: 4 green lights
Level 5: 5 green lights
Level 6: 5 green lights and 1 red light
Level 7: 5 green lights and 2 red lights

15
Troubleshooting
Power lights do not turn on:
If using the mains power adapters, make sure they are plugged in and
switched on.
If using batteries, check they are correctly installed.
Link light does not turn on:
Check that both the baby unit and parent units are switched on.
If using batteries, check they are correctly installed.
Link light is red:
The link between your units is broken. You will also hear an Beep Beep alert
indicating there is no communication between the units, If this happens,
check that the mains power (or batteries) is correctly connected and that the
units are within range of one another.
Parent unit remains silent or very quiet:
The volume setting may be too low.
You may have pressed the Mute button.
You can hear a high pitched noise:
The units are too close to each other, or the volume setting is too high.
Move the parent unit away from baby unit (at least 1 meter / 3 feet).
Decrease volume on the parent unit.
1. Press the volume +and – buttons stimultaneously on the baby unit for
about 3-5 seconds, the link LED will blink in green and red. Press the
volume – button on the baby unit 7 times, the link LED will turn red.
2. Press the volume +and – buttons on both units stimultaneously for
about 3-5 seconds, the link LED on both units should turn green in 2
minutes, and you will receive clear sound.
Pairing

16
Questions
The technical specications show an operat-
ing range of 300 meters / 900 feet outdoors.
How come my baby monitor manages much
less than that?
The specied range is only valid outdoors
in open air. Inside your house the coverage
range is limited by the amount and type of the
walls and/or ceilings in between.
Answer
The link is lost every now and then:
Technical Specifications
Power supply
Care and maintenance
Remove batteries from the unit if you do not plan to use it for a longer period of time
Dispose of used batteries in an environmentally friendly manner.
Clean the baby monitor with a dump cloth if necessary.
Frequently asked questions
1 x charging base with 1 x AC power adapter
DC 6V / 400mA for Parent unit (supplied)
1 x AC power adapter DC 6V / 400mA for
Baby unit (supplied)
Parent
2xAAA rechargeable batteries for
Parent unit
4 x 1.5V AA non rechargeable batteries for
Baby unit (not supplied)
Baby
Operating temperature
0°C ~ 40°C
Operating range
Up to 300 meters / 900 feet outdoors
up to 50 meters / 150 feet indoors
Frequency range
1.88 to 1.9 GHz
Dimension
W:60 mm H:108 mm D:42 mm W:109 mm H:55 mm D:92 mm
Weight
90 g 135 g
0°C ~ 40°C
You are probably approaching the outer lim-
its of the practical range. Try a different loca-
tion or decrease the distance between the
units slightly. Please note that it takes about
5 seconds each time before a new link is es-
tablished.
Up to 300 meters / 900 feet outdoors
up to 50 meters / 150 feet indoors
1.88 to 1.9 GHz