M-system 10VS User manual

10VS / 10VK

P. 1 / 2 EM-0818 Rev.2

INSTRUCTION MANUAL

MODEL

10VS/10VK

SIGNALTRANSMITTER

COMPONENT IDENTIFICATION

INSTALLATION

Use Standard Rack (model: 10BX❑).

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the

connection diagram label on the unit side.

CHECKING

1) Terminal wiring: Check that all cables are correctly

connected according to the connection diagram.

2) Power input voltage: Check voltage supplied to the rack

(model: 10BX❑). For the DC power source, be sure that

the ripple level is within 10% p-p.

3) Input: Check that the input signal is within 0 – 100% of

the full-scale.

4) Output: Check that the load resistance meets the de-

scribed specifications.

Zero Adj.

Span Adj. Output 1

Body

Specification Label

Connection Diagram

Label

(side)

Zero Adj.

Output 2*Span Adj.

Terminal Cover

*Provided only when the second output is selected.

BEFORE USE ....

Thank you for choosing M-System. Before use, check the

package you received as below.

If you have any problems or questions with the product,

please contact M-System's Sales Office or representatives.

■ PACKAGE INCLUDES:

Signal conditioner ................................................... (1)

■ MODEL NO.

Check that model No. described on specification label is

exactly what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when you

use this product, installation, connection and basic mainte-

nance procedures.

POINTS OF CAUTION

■ POWER INPUT RATINGS

• Power input ratings are specified by the model number

suffix code. Check the power input voltage for the unit on the

specification label.

24V DC ±10%, approx. 25mA with Voltage Output 1

approx. 45mA with Current Output 1

■ GENERAL

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ ENVIRONMENT

• Indoor use

• When heavy dust or metal particles are present in the air,

install the unit inside proper housing and ventilate it.

• Do not install the unit where it is subjected to continuous

vibration. Do not apply physical impact to the unit.

• Environmental temperature must be within -5 to +55°C (23

to131°F)withrelativehumiditywithin30to90%RHinorder

to ensure adequate life span and operation.

■ WIRING

• Do not install cables (power supply, input and output) close

to noise sources (relay drive cable, high frequency line, etc.).

• Do not bind these cables together with those in which noises

are present. Do not install them in the same duct.

■ AND ....

• The unit is designed to function as soon as power is

supplied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data sheet.

–

INPUT

OUTPUT 1

–

OUTPUT 2

CONNECTOR

*1 output type has the output 1 connected to the

card-edge connector in parallel.

OUTPUT 2*

POWER

10VS / 10VK

P. 2 / 2 EM-0818 Rev.2

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory to meet the ordered

specifications, therefore you usually do not need any calibra-

tion.

For matching the signal to a receiving instrument or in case

of regular calibration, adjust the output as explained in the

following.

■ HOW TO CALIBRATE THE OUTPUT SIGNAL

Use a signal source and measuring instruments of sufficient

accuracy level. Turn the power supply on and warm up for

more than 10 minutes.

1) ZERO: Apply 0% input and adjust output to 0%.

2) SPAN: Apply 100% input and adjust output to 100%.

3) Check ZERO adjustment again with 0% input.

4) When ZERO value is changed, repeat the above procedure

1) – 3).

5) Go through the same procedure for Output 2. Extender

Card (model: 10EC) is required to access the Output 2

Adjustments on top of the unit maintaining electrical

connection at the rear connector.

EXTERNAL DIMENSIONS mm (inch)

130 (5.12)

3 (.12)

50 (1.97)

82 (3.23)

2–4.3 (.17) dia.

MTG HOLE TERMINAL COVER

7–M3.5 SCREW

8 (.31)

91 (3.58)

99 (3.90 )

25 (.98)

MAINTENANCE

Regular calibration procedure is explained below:

■ CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit according to the "ADJUST-

MENT PROCEDURE" explained earlier.

M-SYSTEM WARRANTY

M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such

productwasoriginallypurchasedifsuchproducthasbeenusedundernormaloperatingconditionsandproperlymaintained,M-System'ssoleliability,andpurchaser'sexclusiveremedies,

under this warranty are, at M-System's option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this warranty. To

submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original sales invoice.