Maco A-TS Series User manual

www.maco.eu
M119317
TECHNOLOGY IN MOTION
PROTECT DOOR LOCKS
A-TS
Automatic door lock timber
ASSEMBLY INSTRUCTIONS
For use
only by certified specialists!

22 WINDOWS · DOORS · SLIDING DOORS
Table of Contents
Item Page
Important Information 4
Key 5
Use of transportation protection devices 6
Instructions for use 7 - 11
Installation instructions 12 - 20
Set lock for day release function (assembler) 13
Day release element assembly on the lock (assembler) 14
MACO day release opener assembly on the striker plate (assembler) 15
Day Release operating instructions (end-customer) 16
 Positions4mmairgap,9/10mmoset 17
 Positions4mmairgap,13mmoset 18
 Positions12mmairgap,9/10mmoset 19
 Positions12mmairgap,13mmoset 20
Door constructions 21 - 22
Timber 4 mm air gap 21
Timber 12 mm air gap 22
DrillingandroutingpatternsMulti-functionhookstrikerplate 23-28
Lock case and multi-function latch with hook locking 23
 Latchesanddeadboltstrikerplate9/10mmoset 24
 Multi-functionhookstrikerplate9/10mmoset 25
 Latchesanddeadboltstrikerplate13mmoset 26-27
 Multi-functionhookstrikerplate13mmoset 28

33
WINDOWS · DOORS · SLIDING DOORS
Table of Contents
Item Page
Positioningofthestrikerplates 29-38
2 Multi-function latches with hooks
  LowK+605,4mmairgap,9/10mmoset 29
  StandardK+730,4mmairgap,9/10mmoset 30
  HighK+980,4mmairgap,9/10mmoset 31
  LowK+605,12mmairgap,9/10mmoset 32
  StandardK+730,12mmairgap,9/10mmoset 33
  HighK+980,12mmairgap,9/10mmoset 34
  StandardK+730,1-fsash,12mmairgap,13mmoset 35
  StandardK+730,2-sash,12mmairgap,13mmoset 36
  HighK+980,1-sash,12mmairgap,13mmoset 37
  HighK+980,2-sash,12mmairgap,13mmoset 38
Lengthening/shortening of the A-TS K+730 39 - 40
Module without additional locking points 39
Module with additional locking points 40
openDoor Access Control Solutions 41 - 52
Overview 41
A-TS Transponder Plus 42
A-TS Transponder Keypad and Touchkey 43
Somfy lock controller 44
Circuit diagram frame-side 45
Circuit diagram button impulse 46
Circuit diagram toggle switch 47
 RoutingpatternTransponderPlus 48
Routing pattern Keypad / Touchkey BT 49
Routing pattern including assembly of connector plate and motor 50
 Cabletransitionforopeningangle≤110°,Timber12Air 51
 Cabletransitionforopeningangle≤180°,Timber4Air,12Air 52

44 WINDOWS · DOORS · SLIDING DOORS
Important
Target
Thisdocumentationisintendedexclusivelyforspecialistcompaniesandcertiedspecialists.
Thework-stepsdescribedhereinmayonlybecarriedoutbycertiedspecialists.
Instructions for use
• Unlessotherwiseindicated,measurementsaremadeinmillimetres.
• Assemble all hardware parts professionally as described in these instructions and observe
allsafetyinstructions.
• Alldiagramsareonlysymbolic.
• Withthespacer-blocksetting,observethetechnicalguidelineNo.3oftheglaziertrade
"Blockingofglazingunits".
• Observethe"GuidelinesandInstructionsforProductandLiability(GIPL)".
• Inform the end-user about the contents of the "Guidelines and Instructions for End Users
(GIEU)".
• Printingerrors,mistakesandchangesarereserved.
Material notes
• The hardware described in this assembly instructions are made from anti-rust material or
galvanicallypaciedsteelandsealedaccordingtoEN12329.Theymustnotbeusedin
environmentswithaggressive,corrosiveaircontent.
• Donotuseacid-curingsealants,asthesecanleadtocorrosionofthehardwareparts.
• Thedoorlockelementsmayonlybesurface-treatedbeforethehardwareisinstalled.
Anysubsequentsurfacetreatmentmayrestrictthefunctionalityofthehardware.Inthiscase,
nowarrantyclaimscanbemadeagainstthehardwaremanufacturer.

5
MF
EV
FFH
K+
K-
5
WINDOWS · DOORS · SLIDING DOORS
Backset
Distance
Handle height
Prolefrontedge
Multi-function latch
End lock
Important Information
Key
Sash rebate height
Case dimension top
Case dimension bottom

6
A
A
6WINDOWS · DOORS · SLIDING DOORS
Simple transport protection devices, wedges or blocks ensure a safe transport of the entire
doorelement.Totaldoorelements.Removeonlyafterinstallation.
Use of transportation protection devices
ATransport protection device position

77
WINDOWS · DOORS · SLIDING DOORS
Instructions for use
Remove swarf from the milled space!
Drill all holes before installation of the lock! Do not force the handle pin through the lock
nut!
Never open the lock case!

88 WINDOWS · DOORS · SLIDING DOORS
Instructions for use
Do not simultaneously press the key and
handle!
Only close the lock with the corresponding
operating key!
Do not use force during the cylinder assembly!
Do not turn the key using force!
The latch of the main lock must not rub
against the striker plate – this also applies to
multi-point locks without door acceleration,
andalllatchesofthesidelocks.Forthis,use
the adjustment option on the striker plates
anddoorhinges.Adjustmentoftheholesin
thestrikerplatesisnotpermitted.

99
WINDOWS · DOORS · SLIDING DOORS
Instructions for use
Only apply load to the handle in the normal
direction! Apply a maximum force of 15 kg in
the direction of actuation (on the handle)!
Two-sash doors must not be forced over the in-
active leaf!
Do not close the lock latch when the door is
open!
The multi-point lock must be replaced as soon
as traces of use of force are visible!

1010 WINDOWS · DOORS · SLIDING DOORS
Instructions for use
Do not carry the door leaf with the handle!
Do not paint or varnish over the padlock bolt
or latch!

1111
WINDOWS · DOORS · SLIDING DOORS
Instructions for use
The door lock (lock case) is delivered with an intensive lubrication of high-performance
greases and must NOT be re-greased!
Lubricate the MF-HO locking element 1x annually!
* Spray grease (455341), ** Rust remover
Do not use lubricating oil, rust remover, silicon spray etc!
Lubricate only with grease or technical Vaseline! Grease the latch and
deadbolt 1x annually!

12
2
3
1
4
ab
c
d
a
e
2
3
3
1
4
2
3
1
4
ab
c
d
a
e
2
3
3
1
4
2
3
1
4
ab
c
d
a
e
2
3
3
1
4
12 WINDOWS · DOORS · SLIDING DOORS
a= faceplate
c= latch
d= latch insert
e= insert leg of latch insert
1Release the screw and
push forward using the
screwdriver!
2Remove the latch!
3Turn the latch over and
place it on the faceplate
(a) so you can press
the insert leg (e) of the
latch insert (d) under the
faceplaterecess(b).
Only then press the
latch in completely!
4Screw in the screw
(Torquemin.1.5Nmto
max.2Nm)!
Crank Multi-function latch
Perform function test!
Installation Instructions

13
2
3
1
13
WINDOWS · DOORS · SLIDING DOORS
1Lock
2Remove the day release screw
(2.5mmhexsocket)
3Unlock
When the day release is pre-set, the main latch is not operated on
motorised operation (door does not automatically spring open)!
Set day release function Manufacturer delivery state
1Lock
2Insert the day release screw
(2.5mmhexsocket)
3Unlock
Installation Instructions
Set lock for day release function (assembler)

14
1
2
3
4
14 WINDOWS · DOORS · SLIDING DOORS
1 Removethefaceplatecover.
2Position the day release element on the back of the faceplate (directly on the latch above
the lock case)
3 andpushontothelockcase.
4Screw on the day release element with the attached TX20 M4x10 screw on the front of the
faceplate!
Installation Instructions
Day release element assembly on the lock (assembler)

15
12
3
15
WINDOWS · DOORS · SLIDING DOORS
1 Demountthelatchelement.
2 MounttheMACOdayreleaseopener.
3 Activatethemechanicalunlockingusingtheleveronthedayreleaseopener*.
* The mechanical unlocking can remain active as the day release is controlled via the day release actuator on the lock
(see “Day Release” operating instructions p.16).
Installation Instructions
MACO day release opener assembly on the striker plate (assembler)

16
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
16 WINDOWS · DOORS · SLIDING DOORS
Activate day release Deactivate day release
Installation Instructions
Day Release operating instructions (end-customer)
1Press the handle so that the locking
element and the multi-function latch are
pulled in!
2Push the day release actuator upwards,
release the handle!
1Press the handle so that the locking
element and the multi-function latch are
pulled in!
2Push the day release actuator
downwards!
The A-TS basic function, automatic locking,
is again active!

1717
WINDOWS · DOORS · SLIDING DOORS
Position of latch and deadbolt
striker plate
Position of striker plate and
multi-function latch with hook
Pressure adjustment:
+/- 2 mm with latches and deadbolt striker plate
+/-1.5mmwithMF-HOstrikerplate
Positioning of notch faceplate = notch striker plate
A rebate clearance of 2-6 mm must be adhered to in the installed state!
Installation instructions
Positions4mmairgap,9/10mmoset

1818 WINDOWS · DOORS · SLIDING DOORS
Position of latch and deadbolt
striker plate
Position of striker plate and
multi-function latch with hook
Pressure adjustment:
+/- 2 mm with latches and deadbolt striker plate
+/-1.5mmwithMF-HOstrikerplate
Positioning of notch faceplate = notch striker plate
A rebate clearance of 2-6 mm must be adhered to in the installed state!
Installation instructions
Positions4mmairgap,13mmoset

1919
WINDOWS · DOORS · SLIDING DOORS
Position of latch and deadbolt
striker plate
Position of striker plate and
multi-function latch with hook
Pressure adjustment:
+/- 2 mm with latch and deadbolt striker plate
+/- 1 mm with MF-HO striker plate
Positioning of notch faceplate = notch striker plate
A rebate clearance of 10-14 mm must be adhered to in the installed state!
Installation instructions
Positions12mmairgap,9/10mmoset

2020 WINDOWS · DOORS · SLIDING DOORS
Position of latch and deadbolt
striker plate
Position of striker plate and
multi-function latch with hook
Pressure adjustment:
+/- 2 mm with latch and shootbolt striker plate
+/-1.5mmwithMF-HOstrikerplate
Positioning of notch faceplate = notch striker plate
A rebate clearance of 10-14 mm must be adhered in the installed state!
Installation instructions
Positions12mmairgap,13mmoset