Matrix SETU VFXTH User manual

SETU VFXTH
Quick Start

SETU VFXTH
Multi-Port SIP based VoIP to FXO-FXS Gateway
Quick Start

Documentation Disclaimer
Matrix Comsec reserves the right to change, at any time, without prior notice, the product design,
specifications, components, as engineering and manufacturing may warrant.
This is a general documentation for all models/configurations of the product. The product may not
support some of the features/facilities described in this document.
While every reasonable effort has been made to ensure accuracy of content in this document,
Matrix Comsec assumes no responsibility for errors or omissions that may occur herein. No
liability is assumed for damages, costs, expenses resulting from unauthorized modifications or
repairs to the product; failure to use information or to comply with the installation, operation and
maintenance instructions contained in this document.
Copyright
All rights reserved. No part of this quick start may be copied or reproduced in any form or by any
means without the prior written consent of Matrix Comsec.
Version V2
Release date: August 12, 2019

Table of Contents i
Contents
Know Your SETU VFXTH ............................................................................... 1
Overview ........................................................................................................... 1
Ports and Connectors ........................................................................................ 2
LEDs .................................................................................................................. 3
Installing SETU VFXTH .................................................................................. 4
Before You Start ................................................................................................ 4
Getting Started .................................................................................................. 4
Connecting SETU VFXTH ................................................................................. 5
Powering ON SETU VFXTH .............................................................................. 7
How to Access Jeeves ................................................................................... 8
Connecting a Computer .................................................................................... 8
Configuring SETU VFXTH ........................................................................... 12
Using the Wizard ............................................................................................. 12
Using Selective Configuration ......................................................................... 13

Matrix SETU VFXTH Quick Start 1
Know Your SETU VFXTH
Thank you for choosing the Matrix SETU VFXTH. Please read the instructions in this Quick Start to
install and operate your SETU VFXTH properly.
This Quick Start is meant to help you install and configure the basic parameters of the system. For
advanced configuration and feature description, please refer the System Manual. To download,
click https://www.matrixtelesol.com/product-manuals.html
You can also view and download the manual by scanning the QR code printed on the Product
Label/Packaging Label.
For product registration and warranty related details, please visit https://www.matrixcomsec.com/
product-registration-form.html
Overview
SETU VFXTH is available in the following configurations:
* SETU VFXTH1600 and SETU VFXTH1616 has been discontinued. However, software support is still
provided through Jeeves for the users who have already installed it.
Sr.NO. Configuration SIP Trunks FXO Ports FXS Ports
Physical Port Labels
FXO FXS
1SETU VFXTH0016 16 016 0P01-P16
2SETU VFXTH0024 24 024 0P01-P24
3SETU VFXTH0032 32 032 0P01-P32
4SETU VFXTH1600* 16 16 0P01-P16 0
5SETU VFXTH3200 32 32 0P01-P32 0
6SETU VFXTH0808 16 8 8 P01-P08 P09-P16
7SETU VFXTH1616* 32 16 16 P01-P16 P17-P32

2 Matrix SETU VFXTH Quick Start
SETU VFXTH0032
Ports and Connectors
System Status Color STS
Reset Button --- To restart the system or to restore the default IP Address.
Ethernet RJ45 To connect to the IP network over a DSL Modem or Router or a LAN Swtich.
P01 to P32a
(FXS Ports)
a. If your SETU VFXTH supports only FXO Ports (SETU VFXTH3200), P01 to P32 will be used to connect
PSTN lines or a PBX. However, if you system supports both FXO and FXS Ports (SETU VFXTH0808) then
P01 to P08 (FXO Ports) will be used to connect PSTN lines or a PBX and P09 to P16 (FXS Ports) will be
used to connect telephone instruments or a Fax Machine or a PBX.
RJ11 To connect standard telephone instruments, or a Fax Machine or a PBX.
24VDC-
2.5A(Max) DC Jack To connect 24VDC, 2.5A power adapter.
Ethernet
Port
Reset
Button
P01 to P32
FXS Ports
Power
Adapter
FAN

Matrix SETU VFXTH Quick Start 3
LEDs1
SETU VFXTH0032 has a Power LED (PWR), a Status LED (STS) and 32 FXS Port LEDS (P01 to
P32). The LEDs indicate the status of the ports, and various events occurring on the ports,
including errors.
SETU VFXTH is easy to install and operate. The built-in web server, JEEVES, allows you to
configure the system parameters and features On-site as well as from a remote location.
1. Depending on the configuration of your SETU VFXTH, the number of FXS/FXO Port LEDs may vary.
LED Description Color
PWR Power LED. Turns on when power is supplied. Single color
STS System LED. Blinks to indicate health of the system. Dual color
P01 to P32 Power LED. Turns on when power is supplied. Single color

Matrix SETU VFXTH Quick Start 4
Installing SETU VFXTH
Before You Start
• Select a suitable location to mount SETU VFXTH.
• Keep the following ready:
• Necessary telecom wiring as well as cable.
• A standalone PC to access the web based configuration tool, Jeeves.
• A SIP Account information to test VoIP connectivity.
• An active trunk line from the PSTN, if required.
•Anystandardtelephoneinstrument, if required.
• Do not install this product near any area where,
• it is exposed to direct sunlight, heat, excessive cold or humidity, dust, oil, corrosive fumes.
• there is a water source (wash basin, tub, shower, pool, sprinkler, etc.)
• there is source of electromagnetic noise such as radio equipment, heavy transformers,
faulty electric chokes of tube-lights, device having a faulty coil.
• Ensure proper electrical earth and telecom earth for the safety of the product and persons
handling it.
• Always wear an electro static discharge preventive wrist wrap or belt and use a grounding mat
when handling the product and its parts.
• Battery: SETU VFXTH contains 3.3V DC Manganese Lithium Battery (ML 2032- Rechargable) of
diameter 20 (-0.2)mm and height 3.2 (-0.3)mm. Battery should be replaced only by authorized
dealers of Matrix. There is a risk of explosion if the Battery is replaced in an incorrect manner.
Please dispose-off used Batteries.
Getting Started
Package Contents
• Unpack the SETU VFXTH package and check the package contents:
•SETUVFXTHUnit
• Power Adapter - 24VDC, 2.5A (Country Specific)
• Ethernet Cable (RJ45)
• Two Screws M7/30 with grips
• Two 19 inch Rack Mounting Clamps
• Mounting Template
• Warranty Card Set

Matrix SETU VFXTH Quick Start 5
If any of these items is missing or damaged, please contact the dealer/reseller from whom
you purchased the system.
• Place the system at the selected site.
If you are mounting the system on a wall, refer to the mechanical dimensions of the product
and use the mounting template for drilling holes on the wall.
Connecting SETU VFXTH
SETU VFXTH0032 has 1 Reset Button, 1 Ethernet (WAN) Port, 32 FXS Ports, 32 SIP Trunks, a
Power Socket and 34 LEDs. Depending on the configuration, the number of FXO Ports, FXS Ports
and LEDs may vary.
If your SETU VFXTH supports only FXO Ports (SETU VFXTH3200), P01 to P32 will be used to connect
PSTN lines or a PBX. However, if you system supports both FXO and FXS Ports (SETU VFXTH0808)
then P01 to P08 (FXO Ports) will be used to connect PSTN lines or a PBX and P09 to P16 (FXS Ports)
will be used to connect telephone instruments or a Fax Machine or a PBX.
Connecting to the IP Network
Before you connect the system to WAN, we recommend that you first connect a computer to the
Ethernet Port of SETU VFXTH, configure the Basic Settings, and then connect to WAN.
• Use the Ethernet cable supplied for the Ethernet Port of SETU VFXTH to connect the system to
the Public network or Private Network.
If connecting to the Public IP Network,
• Plug one end of the Ethernet cable into the Ethernet Port of SETU VFXTH and the other
end into the DSL modem/Router.
LAN Switch/
Hub
Modem/
Router
Computers
Power
Adapter
Standard
Tel ep ho nes

6 Matrix SETU VFXTH Quick Start
If connecting to a Private Network (Behind a NAT Router),
• Plug one end of the Ethernet cable into the Ethernet Port of SETU VFXTH and the other
end into the LAN Switch/Hub.
The default IP Address of the Ethernet Port is: 192.168.1.100
The default Subnet Mask of the Ethernet Port is: 255.255.255.0
Connecting to the CO Network
• Connect the Trunk Lines from the CO Network to the FXO Ports of SETU VFXTH using
standard, good quality, twisted-wire pair of cables with RJ11 plugs.
You may also connect a PBX to the FXO port.
Connecting Telephone instruments
• Connect the analog single line telephone instruments to the FXS ports of SETU VFXTH using
standard, good quality, twisted-wire pair of cables with RJ11 plugs.
You may also connect a Fax machine or a PBX to the FXS port.
IP
Router/
Modem
SETU VFXTH
LAN Switch/
HUB
Computer
Ethernet
WAN
IP
Router/
Modem
SETU VFXTH
LAN Switch/
HUB
Computer
Ethernet
WAN

Matrix SETU VFXTH Quick Start 7
Powering ON SETU VFXTH
•Connectthepoweradapter to SETU VFXTH.
• Plug in the power adapter of SETU VFXTH into the power outlet.
• Switch on power supply and wait for the Reset Cycle to complete.
Reset Cycle
The Reset Cycle (Power-ON Self Test) takes about 2 minutes to finish.
LED Indication - Reset Sequence
At Power ON, Power LED will turn ON (Continuous Green). Initialization process will start within
15 to 20 seconds and LED sequence of all other LEDs during initialization process is shown in the
table given below:
• During Off-hook state, FXS Port LED glows Red continuously.
• If the system is in programming mode, the LED of the port used to enter the programming
mode glows Green continuously. After exiting programming mode, the LED for that port glows
Red (to indicate Off-hook state).
You may now access the web-based programming tool, Jeeves, and configure SETU VFXTH.
System
Status Color STS P01 P02 P03 P04 P05 P06 …. P32 Time (ms)
Application
Load Red OFF ON ON ON OFF OFF OFF OFF OFF
All Init
Done,
System
goes Live
Red ON ON ON ON ON ON ON ON ON 1000
ms
OFF OFF OFF OFF OFF OFF OFF OFF OFF 1000
ms

Matrix SETU VFXTH Quick Start 8
How to Access Jeeves
SETU VFXTH provides an embedded web server with a Graphic User Interface (GUI), Jeeves, for
configuration.
To access Jeeves, you will need to connect a computer to SETU VFXTH.
Connecting a Computer
You may connect a standalone computer to SETU VFXTH or grab any computer connected in the
same LAN as SETU VFXTH.
Connect a standalone computer to SETU VFXTH, when installing the system for the very first time.
You may connect it to the LAN after you have finished installation and configuration of the system.
To connect a standalone computer,
• Plug one end of the Ethernet cable supplied with the system into the Ethernet Port of SETU
VFXTH. Plug the other end into the LAN port of the computer.
• Make sure the IP Address of the computer and the Ethernet Port of SETU VFXTH do not
conflict, and that both are in the same Subnet.
The default IP Address of the Ethernet Port of SETU VFXTH: 192.168.1.100
The default Subnet Mask of the Ethernet Port of SETU VFXTH: 255.255.255.0
• Change the Subnet of the computer, if necessary.
• Make sure a Web-browser, either Internet Explorer version 7 or later or Mozilla Firefox version
3.5 or later, is installed on the computer.
• Open the browser on the computer.
Computer
SETU VFXTH
Ethernet
WAN

Matrix SETU VFXTH Quick Start 9
• In the address bar of the browser, enter the default IP address of the Ethernet Port of SETU
VFXTH: 192.168.1.100
• You will be redirected to the HTTPS protocol for security reasons.
•Clickthehttps://192.168.1.100 link. The Login page will open.
•InLogin Password, enter 1234, the default SE Password.
•ClicktheLogin button.
Before you start configuring the system, if you wish to view or download the SETU VFXTH System
Manual/User Card, you can scan the QR Code present on the login page of Jeeves.

10 Matrix SETU VFXTH Quick Start
• You will be prompted to change the default SE Password.
•InCurrent Password, enter the default SE Password.
• Enter the New Password. All ASCII characters (except Percentage %, Hash #, Equal to =,
Plus +, And &, Backslash \, Less than <, Greater than >, Apostrophe ’ , Double Quote "and
Space) and digits 0to 9are allowed. The new password must be:
• a minimum of 6 characters to a maximum of 16 characters.
• include atleast one upper-case, one lower-case, one number and one special character.
•InConfirm New Password, re-enter the new password to confirm.
• Click Submit. You will be re-directed to the Login page again.
•InLogin Password, enter the new password.
As this password is meant for restricting access to the SE mode, we strongly recommend you to:
• Keep the password secret.
• Select a complex password that cannot be easily guessed.
• Change the password regularly. See Login Password topic in the System Manual for
instructions.
On successful login, the Home page opens.

Matrix SETU VFXTH Quick Start 11
The left navigation bar shows the links Basic Settings, Advanced Settings, Maintenance and
Status.
Basic Settings break down the complexities of configuration and are sufficient to get your
system into operation.
Advanced Settings enable you to configure the advanced features and facilities of SETU
VFXTH.
Maintenance allows you to carry out system maintenance and monitoring activities like
uploading configuration and firmware, debug, system restart.
Status allows you to view the system details and status of all the SIP Trunks, FXO Port,
Ethernet Port and system’s firmware.
• You may now configure the Basic Settings of SETU VFXTH.

Matrix SETU VFXTH Quick Start 12
Configuring SETU VFXTH
There are two ways to do the basic system configuration using Jeeves:
•usingtheWizard.
Or
• through Selective Configuration of basic settings.
Using the Wizard
The configuration Wizard leads you step-by-step through the configuration of the basic settings.
To use the Wizard,
•ClicktheWizard icon on the top right of your screen.The Home page of the Wizard
opens.
• To navigate the Wizard pages use the Next and Back buttons.
• When you press the Next button, the changes on the current page are saved and the Wizard
takes you to the next page.
• When you press the Back button, you will be prompted to save changes made on the current
page.
•Expand : expands a link on the page to display all the parameters under the link.
•Collapse : collapses a link, hides all the parameters under a link on the page.
•Settings : enables you to configure / edit the settings of a parameter further.

Matrix SETU VFXTH Quick Start 13
•Default: assigns factory set values to all the parameters on the page.
•Add: enables you to add a new record/entry.
•Delete: enables you to delete a record/entry.
•Close: enables you to exit a window.
• You may exit the Wizard at any time by clicking the Quit button . The changes you made
before you exit will be saved.
Using Selective Configuration
You can choose the parameters you want to configure, and the order in which you want to
configure. To do this,
•ClicktheBasic Settings link.
• The parameter sub-links appear on the left navigation bar.
• Click the parameter sub-link you wish to configure.
• The respective parameter page opens.
• Get familiar with the buttons and icons listed below before you begin to change the settings of
the parameters on each page.
Expand: expands a link to display all parameters under the link.
Collapse: collapses a link; hides all parameters under the link.
Settings: enables you to configure / edit the settings of a parameter further.

14 Matrix SETU VFXTH Quick Start
Logout: enables you to exit Jeeves.
Default: assigns factory set values to all the parameters on the page.
Add: enables you to add a new record/entry.
Delete: enables you to delete a record/entry.
Close: enables you to exit a window.
• Set the parameters on the page to the desired values and click the Submit button to save.
You may use the Wizard or selectively configure the Basic Settings pages, whichever works best
for you. Read the SETU VFXTH System Manual for detailed instructions.

Version 2, August 2019
MATRIX COMSEC
Head Office
394-GIDC, Makarpura, Vadodara - 390010, India.
Ph: ([phone]
E-mail: [e-mail]
www.MatrixTeleSol.com