McCrometer McMag2000 User manual

30124-77 Rev. 1.2
March 24, 2020
McMag2000™
Battery Powered
Electromagnetic Flow Meter
Installation, Operation and
Maintenance Manual

30124-77 Rev. 1.2 | 24MAR2020
Page ii
Contents
SAFETY SYMBOLS AND WARNINGS..........................................................1
1.0 INTRODUCTION ......................................................................2
2.0 PRINCIPLE OF OPERATION ............................................................2
3.0 INSTALLATION........................................................................2
3.1 Safety ...........................................................................2
3.2 Flow Direction ...................................................................3
3.3 Pipe Run Requirements...........................................................3
3.4 Basic Installation Steps ...........................................................3
3.5 Replacing an Existing Mc Propeller Saddle Meter ...................................4
3.6 Mc Propeller-to-Mc Mag2000 Conversion Kit .........................................4
3.7 Retrotting an Existing Mc Propeller Flow Meter ...................................4
4.0 REGISTER INTERFACE .................................................................6
5.0 FLOW METER SPECIFICATIONS ........................................................7
6.0 DIMENSIONS AND WEIGHTS ..........................................................9
7.0 RETURNING A UNIT FOR REPAIR .......................................................9
WARRANTY STATEMENT ...................................................................10

30124-77 Rev. 1.2 | 24MAR2020
Page 1
Safety symbols and warnings
When installing, operating, and maintaining McCrometer equipment where hazards may be present, you must protect
yourself by wearing Personal Protective Equipment (PPE) and be trained to enter conned spaces. Examples of conned
spaces are manholes, pumping stations, pipelines, pits, septic tanks, sewage digesters, vaults, degreasers, storage tanks,
boilers, and furnaces.
You must follow all state and local laws, as well as Occupational Safety and Health Administration (OSHA) regulations
concerning Personal Protective Equipment and conned-space entry. Specic requirements can be found in the OSHA
section of the Code of Federal Regulations: 29 CFR, 1910.132 - 1910.140, Personal Protective Equipment; and CFR Title 29,
Part 1910.146, Permit-Required Conned-Spaces.
SAFETY SYMBOLS AND WARNINGS
Throughout this manual are safety warning and caution information boxes. Each warning and caution box will be identied
by a large symbol indicating the type of information contained in the box. The symbols are explained below:
This symbol indicates important safety information. Failure to follow the instructions can result in serious
injury or death.
This symbol indicates important information. Failure to follow the instructions can result in permanent
damage to the meter or installation site.
IMPORTANT
i
WARNING
!
WARNING
!Incorrect installation or removal of meters can result in serious injury or death. Read the instructions in
this manual on the proper procedures carefully.
WARNING
!Never enter a conned space without testing the air at the top, middle, and bottom of the space. The
air may be toxic, oxygen decient, or explosive. Do not trust your senses to determine if the air is safe. You
cannot see or smell many toxic gases.
WARNING
!Never enter a conned space without the proper safety equipment. You may need a respirator, gas
detector, tripod, lifeline, and other safety equipment.
WARNING
!Never enter a conned space without standby/rescue personnel within earshot. Standby/rescue
personnel must know what action to take in case of an emergency.
WARNING
!Cutting into a pressurized pipe may cause injury or death. Always insure the pipe is empty BEFORE
cutting.

30124-77 Rev. 1.2 | 24MAR2020
Page 2
Introduction
1.0 INTRODUCTION
The McMag2000 bolt-on saddle meter oers the convenience of installation and operation of a propeller meter with the
accuracy and ease of use of a mag meter. It combines a single point sensor with a battery powered electronic register to
provide accurate ow measurement for full-pipe ow monitoring applications.
The saddle mounted sensor (available for pipe sizes from 4 to 12 inches) uses electromagnetic technology to measure the
water ow and correct for shifting velocity in the pipe by constantly obtaining a mean velocity from the sensor.
The electronic register is powered by a replaceable two cell lithium-thionyl chloride (Li-SOCI2) battery that can provide ow
measurement for ve years (including a ve-year battery warranty).Optional DC power supply is also available.
2.0 PRINCIPLE OF OPERATION
The McMag2000 uses Faraday's Law of electromagnetic induction to measure water velocity. Faraday's Law states that a
conductor, moving through a magnetic eld, produces a voltage.
Charge carriers in the uid produce a voltage when passing through a magnetic eld. The magnitude of the voltage is
directly proportional to the velocity at which the uid moves through the magnetic eld. Electromagnetic coil inside the
sensor produces a magnetic eld, and electrodes on the sensor’s surface measure the voltage generated by the moving
uid. The individual velocity measurements are averaged together providing the average velocity across the pipe center
line. Flow is calculated by multiplying the average velocity by the cross-sectional area of the pipe.
3.0 INSTALLATION
3.1 Safety
Proper meter installation is the rst step to ensure excellent meter performance. Follow these instructions closely. Consult
an authorized service representative or the Factory for any circumstances encountered which are not covered in this
manual.
All McCrometer products are tested and inspected during manufacture and prior to shipping. An inspection should be
performed at the time of unpacking to detect any damage that might have occurred during shipment.
WARNING
!Incorrect installation or removal of meters can result in serious injury or death.
Read the instructions in this manual on the proper procedures carefully.
• Any person installing, inspecting, or maintaining a McCrometer ow meter should have a working understanding of
piping congurations and systems under pressure.
• Before adjusting or removing any meter, be certain the system has depressurized completely.
• Be careful when lifting meters. Meters can cause serious injury if lifted incorrectly or dropped.
• All magnetic ow meters are calibrated for a full pipeline only; if less, the ow meter will over register the ow.
• Although a minimum line pressure is not necessary for an accurate measurement, a full pipe is necessary.
• Before starting a system, make sure all connections are properly secured. Keep a safe and prudent distance away from
the meter during system start-up.

30124-77 Rev. 1.2 | 24MAR2020
Page 3
Installation
3.2 Flow Direction
It is very important to install the ow meter relative to the ow of the water. The sensor must face the ow direction in order
for it to make proper measurements. (Figure 1)
3.3 Pipe Run Requirements
Flow meters are velocity sensing devices and are vulnerable to
certain upstream disturbances. Because of this, meters need
certain lengths of straight pipe before and after the meter. These
distances relate to the diameter of the pipe used. Obstructions
can include elbows, valves, pumps, and changes in pipe diameter.
The uneven ow created by these obstructions can vary with
each system.
Both upstream and downstream distances are measured from
the center of the saddle as shown below. In a typical installation
to achieve ±2% accuracy the McMag2000 ow meter should be
installed a minimum of ve diameters upstream from most ow
disturbers and two diameters downstream of the meter. (Figure 1)
Figure 1. Pipe Run Requirements
The McMag2000 is a saddle type meter. It may be installed
directly onto an existing pipe. Follow these steps for a new ow
meter installation.
1. Cut or hole-saw a round hole minimum 3” in diameter in
the pipe and remove all burrs, slag, and rough edges from
the inside and outside of the cutout section.
2. Loosen and remove the nuts and washers from the straps.
Remove the straps from the saddle.
3. Apply lubrication to the gasket and inner diameter of
U-bolts with MolyKote lubricant or equivalent.
4. Place saddle with gasket in place over the cut out.
5. Place U-bolts underneath the pipe and through the saddle clips.
6. Place the provided washers and nuts on the U-bolts that have been installed through the saddle clips.
7. Start tightening down the nuts evenly in a gure 8 pattern.
7a. Tighten the nuts to 40 ft. lbs. evenly using a gure 8 pattern.
7b. Tighten the nuts to 60 ft. lbs. evenly using a gure 8 pattern.
7c. Tighten the nuts to 80 fts. lbs. evenly using a gure 8 pattern.
8. Go back around and loosen all of the nuts. Do not back the nuts completely o of the U-bolts. The goal is to release
force and tension o of the saddle and the gasket.
9. Repeat steps 7a through 7c exactly as described. Any step that is skipped may result in an improper seal.
10. Apply pressure/turn on pump.
11. Verify the saddle is not leaking water. If it is, repeat steps 8 through 10 until the saddle has sealed.
3.4 Basic Installation Steps
WARNING
!WARNING!
Insure that the line is depressurized
before beginning installation!
Flow Direction
2D
Downstream
5D
Upstream
NOTE
The Mc Mag2000 should not be connected to
any earth ground. Connecting to an earth
ground may adversely aect meter performance.
IMPORTANT
i

30124-77 Rev. 1.2 | 24MAR2020
Page 4
Installation
3.5 Replacing an Existing Mc Propeller Saddle Meter
The McMag2000 has been designed for easy replacement in the eld for Mc Propeller ow meters. When the existing saddle
meter has been removed, follow the basic installation instructions in section 3.4. The replacement ow meter will be fully
assembled and ready to install.
3.6 Mc Propeller-to-Mc Mag2000 Conversion Kit
Check the parts received against the parts list and Figure 2 and Figure 3. Contact the factory to report any discrepancies.
3.7 Retrotting an Existing Mc Propeller Flow Meter
Mc Propeller 4” to 12” saddle ow meters can be retrot to a Mc Mag2000 ow meter. When the existing saddle meter has
been removed, follow the instructions below for converting and reinstalling the ow meter.
The Mc Mag2000 ow meter reuses the saddle and U bolts from an existing ow meter. The register, canopy, base plate,
propeller, and bearing housing are not used. You may wish to keep these components as replacement parts for other
propeller ow meters you have.
1
2
3
4
6
7
8
5.1
5.2
5.3
5
Figure 2. Conversion Kit
Item # Description Part #
1 Converter Unit G2-CONV
2 O-Ring (243 Buna) 1-1551-38
3 Base Plate R0138-10
4 Screw 10-32 x 1.25”Long 10730
5Bushing and O-Ring Assembly
5.1 Bushing R0155-00
5.2 O-Ring (021 Buna) 10273
5.3 O-Ring (121 Buna) 10274
6 Gasket 10023-00
7 O-Ring (024 Buna) 10110-10
8 Sensor EA540-00
NOTE
The Mc Mag2000 can be used to replace existing 4”to 12” Mc Propeller saddle meters. The meter CANNOT be used
to replace a Water Specialties bolt on saddle meter.
IMPORTANT
i
NOTE
During the retrot procedure, make sure you insert all four screws when attaching the converter unit to the
base plate. The converter will not be grounded if the grounding jumper is not connected with both screws. (See
exploded view in Figure 2 and Figure 3.)
IMPORTANT
i

30124-77 Rev. 1.2 | 24MAR2020
Page 5
Installation
Converting the ow meter
Refer to Figure 2 and Figure 3 for the conversion procedure.
1. Remove the ow meter that will be converted to an Mc
Mag2000.
2. Remove all parts from the saddle. Keep the saddle and
the U bolts. All other parts will not be used.
3. Connect the base plate (#3) to the saddle with the
bushing, two o-rings, and gasket (items #5, 6, 7).
4. Place the O-ring (#2) on top of the base plate (#3) and
feed the end of the converter cable through the ell.
5. Plug the cable into the sensor (#8).
6. Twist the sensor counter-clockwise 4-5 times and then
screw the sensor onto the ell.
7. Twist any excess length of cable into the cup section of
the base plate and secure it with screws (#4), ensuring the
O-ring is properly seated in the groove in the bottom of
the converter.
8. Install the saddle as described in section 3.5.
Re-inserting the ow meter
9. Loosen and remove the nuts and washers from the straps.
Remove the straps from the saddle.
10. Apply lubrication to the gasket and inner diameter of
U-bolts with MolyKote lubricant or equivalent.
11. Place saddle with gasket in place over the cut out.
12. Place U-bolts underneath the pipe and through the saddle clips.
13. Place the provided washers and nuts on the U-bolts that have been installed through the saddle clips.
14. Start tightening down the nuts evenly in a gure 8 pattern.
14a.Tighten the nuts to 40 ft. lbs. evenly using a gure 8 pattern.
14b.Tighten the nuts to 60 ft. lbs. evenly using a gure 8 pattern.
14c.Tighten the nuts to 80 fts. lbs. evenly using a gure 8 pattern.
15. Go back around and loosen all of the nuts. Do not back the nuts completely o of the U-bolts. The goal is to release
force and tension o of the saddle and the gasket.
16. Repeat steps 14a through 14c exactly as described. Any step that is skipped may result in an improper seal.
17. Apply pressure/turn on pump.
18. Verify the saddle is not leaking water. If it is, repeat steps 15 through 17 until the saddle has sealed.
Figure 3. Mc Mag2000 assembly
NOTE
Be careful when starting the threads not to cross-
thread.
Hand-tighten only. Do not overtighten the sensor
onto the ell! This many damage the sensor and the
sealing surface.
IMPORTANT
i
Electronic
register
Screws
Ethernet cable
and connector
Saddle
Nut and washer Gasket
Bushing
O-rings
Ell
Top and
bottom
electrodes
U bolts
Sensor
Grounding
jumper

30124-77 Rev. 1.2 | 24MAR2020
Page 6
Register Interface
4.0 REGISTER INTERFACE
The display is activated when the lid is opened. (Figure 4) The display will remain active for 30 seconds. The various parts of
the interface screen is shown below (Figure 5).
Figure 4. Lift lid to activate the display Figure 5. Interface Screen
1
2
3
4
5
6
Rate
Total
Total unit
Multiplier
Rate unit
Alarms
NOTE
To save battery life, always close the lid after reading the display. If the lid is kept open, the display will remain
on, reducing battery life.
If the lid is lost, contact the factory immediately for a replacement.
IMPORTANT
i

30124-77 Rev. 1.2 | 24MAR2020
Page 7
FLOW METER SPECIFICATIONS
5.0 FLOW METER SPECIFICATIONS
McMag2000 with EasyRead Technology is designed for simplicity at an aordable price. The meter uses a small sensor
with two electrodes measuring in the center of the pipe, and easy to read (no scrolling) rate and totalizer on one screen.
The meter comes battery powered as a standard with no outputs. However, it oers pulse out and DC powered options
available as adders. McMag2000 with Easy Read Technology has industry standard ±2% accuracy while boasting a full 5
year warranty.
Flow Meter Specications
30122-86 Rev. 1.1 | unreleased
Page 4
Specication Sheet
McMag2000™ Flow Meter
Description and Operating Specications
Volumetric ow in lled ow conduits 4”to 12”utilizing saddle installed sensor. Flow
indication in English Standard or Metric units.
Method Electromagnetic
Pipe Sizes and Flow
Rates
4” 40 - 600 gpm
6” 90 - 1350 gpm
8” 150 - 2350 gpm
10” 240 - 3700 gpm
12” 350 - 5300 gpm
Body Style Saddle mount
Pressure 150 psi (10.3 bar) working pressure
Accuracy ±2% accuracy, or ±0.25% of standard full scale ow
Empty Pipe
Detection Hardware/Software, conductivity-based
Electrical
connections
Optional shielded cable for 10-35VDC
Optional shielded cable for pulse out
Pipe Run
Requirements 5D Upstream / 2D Downstream
Retrot Available using Mc® Propeller saddle
Display and Measurement
Display
• Large LCD display (no backlight)
• Non-volatile memory
• Anti-reverse totalizer (standard)
• Total (to 9 digits of precision)
• Flow Rate and Velocity (to 5 digits of precision)
• Low battery and empty pipe indication
• Opening lid activates display
Digits 5 Rate, 9 Total
Units
Gallons per minute
Million gallons per day
Cubic feet per second
Megaliters per day
Liters per second
Cubic meters per hour
Liters per minute
Gallons per hour
Imperial gallons per minute
Miner’s inch (9G)
Miner’s inch (11.22G)
Acre-feet per day
Kiloliters per hour
Liters per hour
Cubic meters per minute
Cubic feet per minute
Barrels per minute (55G)
Barrels per hour (55G)
Barrels per day (55G)
Barrels per minute (42G)
Barrels per hour (42G)
Barrels per day (42G)
Power
Battery Standard: two 3.6V lithium-thionyl chloride (Li-SOCI2) D size batteries. Batteries are eld
replaceable. Unit contains backup battery.
DC Power Linear power supply 10-35VDC, 2W
Battery Life Five-year expected battery life, ve-year battery warranty.
Note: Battery expectancy is with standard conguration

30124-77 Rev. 1.2 | 24MAR2020
Page 8
FLOW METER SPECIFICATIONS
Flow Meter Specications
30122-86 Rev. 1.0 | 20FEB2020
Page 4
Specication Sheet
McMag2000™ Flow Meter
Environmental
Operating
Temperature 10° to 140°F (-12° to 60°C) sensor
Storage
Temperature -20° to 149°F (-29° to 65°C)
Operating Pressure 150 PSI
Water
Impermeability IP67
Outputs
Pulse Output One digital pulse (open collector) output for volumetric
Options and Accessories
• Epoxy coated carbon steel anged spool piece
• DC power w/battery backup
• Annual verication / calibration
• Stainless Steel ID tag
• Boot cover
Materials
Sensor Body HDPE plastic
Electrodes Stainless steel (316)
Saddle Mount Stainless steel (304)
Saddle Hardware Stainless steel (304)
Electronic Housing IP-67 Certied diecast aluminum, powder coated enclosure w/ tamper resistant seal, 6” x 6”x
5” tall
Saddle Gasket Neoprene
Boot Cover EPDM rubber optional
Warranty
Meter 5-year standard warranty
Battery 5-year warranty

30124-77 Rev. 1.2 | 24MAR2020
Page 9
DIMENSIONS AND WEIGHTS
6.0 DIMENSIONS AND WEIGHTS
7.0 RETURNING A UNIT FOR REPAIR
If the unit needs to be returned to the Factory for repair, please do the following:
• Prior to calling for a return authorization number, determine the model number, serial number (located inside the front
panel of converter), and reason for return.
• Call the McCrometer Customer Service Department at 951-652-6811 and ask for a Return Authorization (RA) number.
• Ship the meter in the original packaging, if possible. Do not ship manuals, power cords, or other parts with your unit
unless required for repair.
• Please make sure the meter is clean and free from foreign debris prior to shipping.
• Write the RA number on the outside of the shipping box. All return shipments should be insured.
• Address all shipments to:
McCrometer, Inc.
RMA #
3255 W. Stetson Avenue
Hemet, CA 92545
Dimensions and Weights
30122-86 Rev. 1.0 | 20FEB2020
Page 5
Specication Sheet
McMag2000™ Flow Meter
3255 WEST STETSON AVENUE • HEMET, CALIFORNIA 92545 USA
TEL: [phone] • 800-220-2279 • FAX: [phone]
www.mccrometer.com
Copyright © 2020 McCrometer, Inc. All printed material should not be changed or altered without permission of McCrometer. Any published pricing, technical
data, and instructions are subject to change without notice. Contact your McCrometer representative for current pricing, technical data, and instructions.
Page 5
FLOW
DIMENSIONS
Meter and Nominal Pipe Size 4 6 8 10 12
Minimum Flow U.S. GPM 40 90 150 240 350
Maximum Flow U.S. GPM 600 1350 2350 3700 5300
Approx. Shipping Weight-lbs. 13 15 18 20 24
A (inches) 5 1/2 9 9 9 9
B (inches) 10 3/4 13 1/4 13 1/4 13 1/4 14 1/4
C (inches) 7 8 8 9 1/2 9 1/2
D (inches) 33333
E (inches) 13 1/4 16 1/2 17 1/2 19 1/2 21 1/2
REQUIRED ORDERING INFORMATION: Pipe O.D. and I.D. are required for all saddle meter orders.
MIGHTY MAG DIMENSIONS
Meter and Nominal Pipe Size 4 6 8 10 12
Maximum Flow U.S. GPM 600 1350 2350 3700 5300
Minimum Flow U.S. GPM 40 90 150 240 350
Approx. Shipping Weight TBD TBD TBD TBD TBD
A(inches) 5 1/2 9 9 9 9
B(inches) 10 3/4 13 1/4 13 1/4 13 1/4 14 1/4
C(inches) 7 8 8 9 1/2 9 1/2
D(inches) 3* 3* 3* 3* 3*
E(inches) 13 1/4 16 1/2 17 1/2 19 1/2 21 1/2
*STANDARD HOLE CUT-OUT FOR EXISITING
M0300 METERS IS ACCEPTABLE.
*STANDARD HOLE CUT-OUT FOR EXISITING
M0300 METERS IS ACCEPTABLE.
MIGHTY MAG DIMENSIONS
Meter and Nominal Pipe Size 4 6 8 10 12
Maximum Flow U.S. GPM 600 1350 2350 3700 5300
Minimum Flow U.S. GPM 40 90 150 240 350
Approx. Shipping Weight TBD TBD TBD TBD TBD
A(inches) 5 1/2 9 9 9 9
B(inches) 10 3/4 13 1/4 13 1/4 13 1/4 14 1/4
C(inches) 7 8 8 9 1/2 9 1/2
D(inches) 3* 3* 3* 3* 3*
E(inches) 13 1/4 16 1/2 17 1/2 19 1/2 21 1/2
FLOW
A
C
B
E

30124-77 Rev. 1.2 | 24MAR2020
Page 10
WARRANTY STATEMENT
WARRANTY STATEMENT
McCrometer warrants that this product will be free from
defects in material and workmanship for a period 5 (ve)
years from the date the equipment was rst installed for
all parts and components including hardware, electronics,
sensor, and battery.
Repairs shall be warranted for 12 months or, if the repair
is performed under this warranty, for the remainder of the
original warranty period, whichever is less.
Buyer shall report any claimed defect in writing to
McCrometer immediately upon discovery and in any
event, within the warranty period. McCrometer shall, at its
sole option, repair the equipment or furnish replacement
equipment or parts thereof, at the original delivery point.
McCrometer shall not be liable for costs of removal,
reinstallation, or gaining access. If Buyer or others repair,
replace, or adjust equipment or parts without McCrometer
prior written approval, McCrometer is relieved of any further
obligation to Buyer under this Article with respect to such
equipment.
No equipment furnished by McCrometer shall be deemed
to be defective by reason of normal wear and tear, failure
to resist erosive or corrosive action of any uid or gas
(unless otherwise specied in Quotations/ Purchase Order
Specications), Buyer’s direct or indirect failure (or the
failure of its agents or contractors) to properly store, install,
operate, or maintain the equipment in accordance with
good industry practices or specic recommendations
of McCrometer, or Buyer’s failure to provide complete
and accurate information to McCrometer concerning the
operational application of the equipment.
THE FOREGOING LIMITED WARRANTIES WITH RESPECT
TO EQUIPMENT AND PRODUCTS ARE EXCLUSIVE AND
IN LIEU OF ANY AND ALL OTHER WARRANTIES OF
QUALITY OR PERFORMANCE, EXPRESS, IMPLIED OR
STATUTORY, INCLUDING, WITHOUT LIMITATION, ANY
AND ALL WARRANTIES OF MERCHANTABILITY OR
FITNESS OF SAID EQUIPMENT AND PRODUCTS FOR ANY
PARTICULAR PURPOSE.
MCCROMETER DISCLAIMS ANY WARRANTY, WHETHER
EXPRESS OR IMPLIED, REGARDING THE SUITABILITY
OF PRODUCTS AND EQUIPMENT SUPPLIED PURSUANT
TO ANY PURCHASE ORDER FOR INSTALLATION IN ANY
PARTICULAR SYSTEM OF SYSTEMS. MCCROMETER
MAKES NO WARRANTY OF ANY KIND WITH RESPECT TO
ANY SERVICES PERFORMED BY MCCROMETER OR ITS
AGENTS PURSUANT TO ANY QUOTATION.
Purchaser’s sole remedy and manufacturer’s sole obligation
for alleged product failure, whether under warranty
claim or otherwise, shall be the aforestated obligation of
manufacturer to repair or replace products returned within
twenty-four months after date of original shipment. The
manufacturer shall not be liable for, and the purchaser
assumes and agrees to indemnify and save harmless
the manufacturer in respect to, any loss or damage that
may arise through the use by the purchaser of any of the
manufacturer’s products.
All product warranties and guarantees set forth herein shall
only be enforceable if (a) all equipment is properly installed,
inspected regularly and is in good working order, (b) all
operations are consistent with Supplier recommendations,
(c) operating conditions at the Customer site have not
materially changed and remain within anticipated
specications, and (d) no reasonably unforeseeable
circumstances exist or arise.
McCrometer does not authorize any person or entity
(including, without limitation, McCrometer agents and
employees) to make any representations (verbal or
written) contrary to the terms of this limited warranty or
its exclusions. Such terms of this limited warranty and its
exclusions can only be eectively modied in writing and
only by the President of McCrometer.
BATTERY GUARANTEE:
Main power batteries will be replaced at no charge should
they fail within 5 (ve) years from the date of purchase with
the meter. Guarantee is not valid for replacement batteries.
Guarantee is limited to the a one-time replacement of the
main power batteries. McCrometer is not responsible for
any lost data or any other direct or indirect losses resulting
therefrom. The batteries and their conguration are specic
to the Dura Mag ow meter and only McCrometer batteries
can be used. Any use of batteries other than those supplied
from McCrometer will void the above Warranty.

30124-77 Rev. 1.2 | 24MAR2020
Page 11
3255 WEST STETSON AVENUE • HEMET, CALIFORNIA 92545 USA
TEL: [phone] • 800-220-2279 • FAX: [phone]
www.mccrometer.com
Copyright © 2001-2019 McCrometer, Inc. All printed material should not be changed or altered without permission of McCrometer. Any published pricing,
technical data, and instructions are subject to change without notice. Contact your McCrometer representative for current pricing, technical data, and instructions.
Page 11
™
DURA MAG
™
FlowConnect
OTHER McCROMETER PRODUCTS INCLUDE:
Propeller Flowmeters
Dierential Pressure Flowmeters
Wireless Monitoring System
Magnetic Flowmeters