McCrometer SPI Mag 282L User manual

Model 282L Single Point Insertion
Electromagnetic Flow Meter
1” and 2” Sensors
Installation, Operation and
Maintenance Manual
24511-13 Rev. 1.9
February 1, 2021

24511-13 Rev. 1.9 | 01FEB2021
Page ii
Contents
1.0 SAFETY SYMBOLS AND WARNINGS ....................................................1
1.1 Safety Symbols .................................................................1
1.2 Safety Warnings.................................................................1
2.0 SPI MAG DESCRIPTION OF COMPONENTS..............................................2
2.1 Overview .......................................................................2
2.2 Flow Calculation ................................................................3
2.3 Proling Information ............................................................3
2.4 Full Pipe Sensors ................................................................3
3.0 PARTS DIAGRAMS ....................................................................4
4.0 SENSOR PROBE INSTALLATION ........................................................5
4.1 Site Selection ...................................................................5
4.2 Sensor Clearance................................................................5
4.3 Pipe Valve Installation ...........................................................6
4.4 Sensor Assembly Installation ....................................................6
4.5 Inserting The Sensor.............................................................7
4.6 Clean Water Sensor Position .....................................................7
4.7 Raw Water Sensor Position.......................................................8
4.8 Sensor Insertion Tool ............................................................8
5.0 SENSOR REMOVAL....................................................................9
6.0 MAINTENANCE .......................................................................9
7.0 SPECIFICATIONS.....................................................................10
8.0 SPI MAG ORDERING INFORMATION...................................................14
9.0 CONVERSION TABLES ................................................................15
WARRANTY STATEMENT ...................................................................16

24511-13 Rev. 1.9 | 01FEB2021
Page 1
Safety Symbols And Warnings
1.2 Safety Warnings
When installing, operating, and maintaining McCrometer equipment where hazards may be present, you must protect
yourself by wearing Personal Protective Equipment (PPE) and be trained to enter conned spaces. Examples of conned
spaces are manholes, pumping stations, pipelines, pits, septic tanks, sewage digesters, vaults, degreasers, storage tanks,
boilers, and furnaces.
You must follow all state and local laws, as well as Occupational Safety And Health Administration (OSHA) regulations
concerning Personal Protective Equipment, conned-space entry, and exposure to bloodborne pathogens. Specic
requirements can be found in the OSHA section of the Code of Federal Regulations: 29 CFR, 1910.132 - 1910.140, Personal
Protective Equipment; CFR Title 29, Part 1910.146, Permit-Required Conned-Spaces; and 29 CFR, 1910.1030, Bloodborne
Pathogens.
1.0 SAFETY SYMBOLS AND WARNINGS
1.1 Safety Symbols
Throughout this manual are safety warning and caution information boxes. Each warning and caution box will be identied
by a large symbol indicating the type of information contained in the box. The symbols are explained below:
This symbol indicates important safety information. Failure to follow the instructions can result in serious
injury or death.
This symbol indicates important information. Failure to follow the instructions can result in permanent
damage to the meter or installation site.
WARNING!
Never enter a conned space without testing the air at the top, middle, and bottom of the space. The air may
be toxic, oxygen decient, or explosive. Do not trust your senses to determine if the air is safe. You cannot see or
smell many toxic gases.
WARNING!
Never enter a conned space without the proper safety equipment. You may need a respirator, gas detector,
tripod, lifeline, and other safety equipment.
WARNING!
Never enter a conned space without standby/rescue personnel within earshot. Standby/rescue personnel
must know what action to take in case of an emergency.
WARNING!
Pressurized pipes should only be hot tapped, cut, or drilled by qualied personnel. If possible, depressurize
and drain the pipe before attempting any installation.
WARNING!
Incorrect installation or removal of SPI Mag meters can result in serious injury or death. Read the instructions
in this manual on the proper procedures carefully.
WARNING!
Carefully read all safety warning tags attached to the meter.
!
!
!
!
!
!
!
i

24511-13 Rev. 1.9 | 01FEB2021
Page 2
SPI Mag Description of Components
2.0 SPI MAG DESCRIPTION OF COMPONENTS
2.1 Overview
The SPI Mag Model 282L owmeter combines an innovative sensor with a comprehensive electronics package to provide
accurate ow measurement for full-pipe ow monitoring applications.
The insertable sensor (available for one-inch and two inch taps) uses electromagnetic technology to measure water velocity.
The streamlined, debris-shedding sensor shape allows the SPI Mag to be used under many ow conditions.
SPI Mag has many features to suit a wide variety of applications, and is easily set up using the keypad and readouts. Refer
to the converter manual shipped with your meter system.
Figure 2. 1” and 2” Sensor with Insertion Hardware
The valves are optional or supplied by the customer, and are shown for illustration only.
NOTE
The converter and sensor are supplied as a matched system. (Figure 1 and Figure 2) Verify the system serial numbers
on both the converter and sensor match. This will ensure a properly calibrated system. The System Serial Numbers
begin with MM20##### and are located on the side of the converter and on a tag near the end of the sensor cable.
i
Figure 1. Procomm Series remote
mount converter

24511-13 Rev. 1.9 | 01FEB2021
Page 3
SPI Mag Description of Components
Figure 3. 2” and 1” 282L Sensors
NOTE: It is required that the exact inside diameter of the pipe is input into the ow computer for the SPI Mag to
provide accurate ow data.
2.2 Flow Calculation
The velocity measurements provided by the full-pipe sensor are used to calculate ow. Flow (also known as Q, as the ow
rate, or as throughput) is the amount of uid moving through a pipe in a period of time. For example, if 100 gallons of water
move past the sensor in one minute, the ow is 100 gallons per minute (GPM).
To calculate the ow, two things are needed: The cross-sectional area of the pipe and the average velocity.
Cross-sectional area is found using the inside diameter of the pipe.
Average velocity is found using the sensed velocity (measured by the sensor). A site calibration is performed to determine
the velocity prole. This allows the owmeter to calculate the average velocity from the sensed velocity.
Flow is calculated by using the Continuity Equation:
Flow = Average Velocity x Area
2.3 Proling Information
For information about the Proling and Site Calibration, refer to these documents:
• One Inch Full Pipe Sensor Installation and Proling Guide, Lit.# 24510-58.
• Two Inch Full Pipe Sensor Installation and Proling Guide, Lit.# 24510-59.
2.4 Full Pipe Sensors
The full pipe sensor makes use of Faraday’s Law of Electromagnetic Induction to measure water velocity. Faraday’s Law
states a conductor, moving through a magnetic eld, produces a voltage.
Because water is a conductor, water moving through a magnetic eld produces a voltage. The magnitude of the voltage is
directly proportional to the velocity of the water. The sensor generates an electromagnetic eld, creating a voltage in the
water. The two velocity electrodes, along with the ground electrode measure this voltage. A faster water velocity produces
a higher voltage. By accurately measuring this voltage, the velocity is determined. (Figure 3)
i
Grounding
Electrode
Velocity Electrodes
2" Sensor
Grounding
Electrode
1" Sensor
Velocity
Electrodes

24511-13 Rev. 1.9 | 01FEB2021
Page 4
Parts Diagrams
3.0 PARTS DIAGRAMS
Figure 4. Parts Diagrams
Item
Number Part Name and Part Number
1Sensor Assembly 1" 60080X001
Sensor Assembly 2" 600028X001
2Ball Valve 1” Bronze 43801
Ball Valve 2” Bronze 43055
3Compression Seal Assembly 1" 800003801
Compression Seal Assembly 2" 42205
4
1” Insertion Tube with Cap
12" 42292
24" 42292-1
36" 42292-2
2” Insertion Tube without Cap
18" 42198
24" 42198-1
30" 42198-2
Over 30” use SS tube 42204-xx
5Insertion Tube Cap 1” Consult Factory
Insertion Tube Cap 2” 55042
63/8” SS Long Threaded Rod 42199
NOTE: Valves are optional or supplied by user.
282L 1” Sensor
1 2 3 4 5
6
282L 2” Sensor
1 2 3 4 5
6

24511-13 Rev. 1.9 | 01FEB2021
Page 5
Sensor Probe Installation
4.0 SENSOR PROBE INSTALLATION
Please read the following information before installing the SPI Mag Sensor
4.1 Site Selection
Install the sensor at an adequate distance from elbows,T-junctions, Y-junctions, active valves.Whenever possible, install the
sensor upstream from a bend or junction.
4.2 Sensor Clearance
The sensor will protrude from the pipe when installed demanding sucient clearance (distance H, in Figure 5 below) from
any obstruction for the purposes of installation and removal.
Figure 5. Sensor Clearance Distance
Distance H above is estimated by adding three measurements:
1. The height from the outer pipe wall to the top of the installation valve
2. The length of the meter (see the table below)
3. Additional 9”of working space
Insertion Tube
Length
Overall Sensor
Length
12” 18.25”
1” 282L 24” 30.25”
36” 42.25”
18” 24.25”
2” 282L 24” 30.25”
30” 36.25”
Obstruction
H

24511-13 Rev. 1.9 | 01FEB2021
Page 6
Sensor Probe Installation
4.4 Sensor Assembly Installation
The sensor assembly uses a compression seal, which keeps the
sensor watertight when the pipe is under pressure. (Figure 7) Care
must be taken when installing the sensor, to avoid leaks.
1. Visually inspect all elements of the installation to ensure they
are structurally sound and of high quality materials, including
all welds, couplings and nipples. To prevent future corrosion,
nipples should be high quality stainless steel.
2. Put a generous amount of the pipe sealant (supplied with
the sensor) on the compression seal threads. (Teon tape
may also be used.) NOTE: if pipe sealant gets on the sensor
electrodes the velocity signal may be lost.
3. Place the compression seal threads over the pipe valve. Turn
the entire sensor assembly clockwise to secure the assembly
to the valve.
4. The seal is secure when a large amount of force is required to
turn the assembly. Line up the arrow (on the top plate) with
the direction of the ow.
Figure 6. Installation Valve Options
Compression
Seal Threads
Bottom Plate
Compression
Seal Assembly
4.3 Pipe Valve Installation
Install a 2”(50mm) full port valve or corporation stop with a 2”(50mm) NPT female pipe thread output for the 2”sensor, or a
1”(25mm) full port valve or corporation stop with a 1”(25mm) NPT female pipe thread output for the 1”sensor. Follow any
and all installation instructions provided for the valve that you have chosen. The valve or corporation stop can be installed
onto a welded coupling or pipe saddle. See Figure 6.
Figure 7. Sensor Installation
WARNING!
Pressurized pipes should only be hot tapped, cut, or drilled by qualied personnel using high quality saddles,
valves ad stainless steel nipples. If possible, depressurize the pipe before attempting any installation.
!
IMPORTANT: The
MINIMUM port inside
diameter for all
installation valves is
1-7/8" (48mm).
i
Pipe Saddle
With Ball Valve
Welded Pipe
Nipple
With Ball Valve
Corporation
Stop
Female threads
are NPT
Male threads
are AWWA.

24511-13 Rev. 1.9 | 01FEB2021
Page 7
Sensor Probe Installation
4.5 Inserting The Sensor
Ensure the compression seal is only hand tightened.
1. Barely crack open the valve and tighten the compression seal as required to minimize leaks. A towel draped around the
compression seal can reduce spray if necessary.
2. Open the valve completely. Failure to open the valve completely will cause the valve to scrape the sensor during
insertions and may result in permanent damage to the sensor.
3. Insert the sensor into the pipe by simultaneously rotating clockwise the two captive nuts on the top plate for the 2”
sensor, and the single captive nut on the 1” sensor. (Figure 8) For the two captive nuts on the 2” sensor use the two
ratchet wrenches provided. It is recommended that the sensor insertion tool (p/n 75031) be used to rotate the captive
nuts on the 2” sensor to ensure the top plate compresses evenly. See section 4.8 and Figure 12.
4.6 Clean Water Sensor Position
If the ow is clean water the sensor can be placed at
1/8 of the inside diameter. To position the sensor at
1/8 of the ID, follow the instructions below:
• Measure the tube from the top of the cap
to the end of the sensor to nd the tube
length (TL).
• Calculate (1/8 ID): 1/8 ID = 0.125 x Pipe ID
• Add wall thickness to 1/8 ID.
• Calculate distance A: A = TL - (1/8 D + WT)
• Set the top edge of the insertion tube cap distance A from the pipe.
Figure 9. Tube Length (TL)
TL
WARNING!
The compression seal/sensor assembly may be under pressure. Serious injury may result if proper procedures are
not followed. Do not attempt to install the sensor without the restraining rods fully assembled.
IMPORTANT
On the 2” installation hardware, if the captive nuts
are not tightened simultaneously, the top plate will
become crooked and cause the sensor to be inserted
at an angle and may cause permanent damage to the
sensor.
Figure 8. Captive Nuts
Captive Nuts
Compression
Seal
!
i

24511-13 Rev. 1.9 | 01FEB2021
Page 8
Sensor Probe Installation
4.8 Sensor Insertion Tool
McCrometer recommends using a sensor insertion tool (Figure 12) (P/N
75031) to help with inserting the sensor and to avoid any damage to the
sensor. Place the proling insertion tool over the captive nuts and lock it
into place with spring locks located on the bottom of the tool. Using the
provided wrench rotate the high gear shaft clockwise until the bottom of
the sensor reaches the far wall of the pipe.
Figure 11. 0.00 Position
4.7 Raw Water Sensor Position
The operation position for raw waste water and sludge is at sensor location 0.00 to prevent debris from collecting on the
sensor and aecting velocity readings. To position the sensor at this location follow the instructions below:
• Calculate distance A by subtracting the pipe wall thickness (WT) and ¾”from length C. See Figure 11 for Length C
(Tube Length).
• Position the top edge of the insertion tube cap distance A from the pipe.
If the ow is clean water, the sensor can be left at the 1/8 D position. (Figure 10) Do not leave the sensor in this position for
raw waste water because debris could collect on the sensor and aect the velocity readings. In waste water applications,
position the sensor at location 0.00. See section 4.7.
Figure 10. 1/8 ID Position
Figure 12. Sensor Insertion Tool
3/8" Insertion Tool (Part Number 75031)
for TSL < 72" and pressure < 200 psi
Low Gear Shaft
High Gear Shaft
1/8 D
TL
C
A
A
WT
WT
3/4”

24511-13 Rev. 1.9 | 01FEB2021
Page 9
Sensor Removal
1. Visually inspect the pipe and entire assembly for damage or corrosion paying close attention to any nipples and
welded couplings. If there is any doubt as to the condition of any element of the pipe or sensor, depressurize the line
before attempting a removal of the sensor.
2. Loosen the compression seal until the seal just begins to leak. This will relieve the pressure on the compression seal
allowing the sensor to be removed. Draping a towel around the compression seal can reduce any spraying water.
NOTE: The compression seal may prevent immediate leakage on sensors installed for a long period of time until the
sensor begins to rise.
3. On the 1”sensor, rotate the captive nut on the top plate to raise the sensor.. On the 2”sensor rotate the captive nuts on
the top plate simultaneously. The sensor insertion tool is recommended. See Section 4.8. This will cause the sensor to
rise out of the pipe. If the line is under pressure do not remove the sensor from the compression seal completely. Only
raise the sensor until it is clear of the valve, but still below the compression seal. Once the sensor has cleared the valve
mechanism, the valve can then be closed. Do not attempt to force the valve closed while the sensor is still passing
through the valve as permanent damage to the sensor can occur.
4. Once the valve is closed, the entire sensor can be removed from the valve.
5.0 SENSOR REMOVAL
WARNING!
The pipe may be under pressure. Serious injury or death may result if proper procedures are not followed. To
remove the sensor follow the steps below:
!
6.0 MAINTENANCE
The SPI Mag is essentially a maintenance free meter with no user serviceable parts. However, the metered uid may
contain of solids or other contaminants coat the sensor electrodes. A periodic inspection may be recommended to ensure
the sensor electrodes are clean. To clean the unit remove the sensor following all of the instructions and safety warning
contained in Section 5.0. When the sensor is removed from the pipe, carefully wipe down the sensor with a soft cloth and
a mildly abrasive detergent, such as a liquid kitchen detergent.

24511-13 Rev. 1.9 | 01FEB2021
Page 10
Specications
7.0 SPECIFICATIONS
Specication Sheet
SPI Mag Model 282L Flow Meter with ProComm Converter
24511-12 Rev. 1.9 | 01FEB2021
Page 2
FLOW METER SPECIFICATIONS
Measurement
• Volumetric ow in lled ow conduits 2”(50mm) to 96”(2,440 mm) diameter utilizing
insertable velocity sensor. 1”meter = 2”to 30”pipe I.D.; 2” meter = 6” to 96” pipe I.D.
• Flow indication in English Standard or Metric units
Flow Measurement
Method Electromagnetic
Accuracy ±2% of reading ±0.03 ft/s (±0.009 m/s) zero stability from 0.3 to 32 ft/s (0.09 to 10 m/s)
velocity range
Velocity range +0.3 to +32 ft/s (+0.09 to +10 m/s)
Direction
measurement Has reverse ow indication
Materials
Sensor Polyurethane exposed to ow
2” sensor mounting: PVC and Stainless Steel exposed to ow. (Stainless Steel Insertion Tube Optional)
Compression seal Buna “N” O-Ring seal exposed to ow
Environmental Ranges
Pressure/
temperature limits
• PVC Insertion Tube: Up to 105°F (41°C) at 150 PSI
• Stainless Steel Insertion Tube: Up to 160°F (71°C) at 250 PSI (McCrometer recommends the
use of Stainless Steel)
Note regarding storage: During freezing conditions and when meter is not in use, sensor
must be removed from pipe and stored in dry conditions.
NOTE: Damage to the sensor caused by allowing the sensor freeze in the pipe is not
covered by the warranty.
Electrical Connections
Compression gland seals for 0.125”to 0.375”dia. round cable
Sensor Cable Lengths
Standard 25’McCrometer supplied submersible cable with each remote mount unit.
Optional Up to 200 feet, or 25 feet max for battery powered.
IP Rating
IP68 submersible sensor

24511-13 Rev. 1.9 | 01FEB2021
Page 11
Specications
Specication Sheet
SPI Mag Model 282L Flow Meter with ProComm Converter
24511-12 Rev. 1.9 | 01FEB2021
Page 3
Insertion Tube
To determine insertion tube length for typical near wall installations, divide the pipe I.D. by 8 and add 18”.
For full proles, add 18”to the pipe I.D.
Tube assemblies include rods and mounting hardware
1” tube • Stainless steel tube, 12” length. Will prole 4” pipe I.D.
• Stainless steel tube, 24”length. Will prole 16”pipe I.D.
• Stainless steel tube, 36”length. Will prole 28”pipe I.D.
2” tube • PVC tube, 18”length. Will prole a 10”pipe I.D.
• PVC tube, 24”length. Will prole a 16”pipe I.D.
• PVC tube, 30”length. Will prole a 22”pipe I.D.
• Opt.: stainless steel tube. Specify length - 65”maximum
System Options
• Stainless Steel ID Tag
• Sensor Insertion Tool
• Additional Sensor Cable up to 200’(for longer lengths consult factory)
• Valves
Ordering Requirements
At the time of ordering, please be prepared to provide the following information:
• Model and tap size
• Insertion tube length
• Pressure
• Minimum ow
• Maximum ow
• Typical ow
• Fluid
• Pipe I.D.
• Cable length
• Temperature
• Any other chemicals in use
• Indicator and totalizer units

24511-13 Rev. 1.9 | 01FEB2021
Page 12
Specications
9.0 SPECIFICATIONS
30124-60 Rev. 1.4 | 01FEB2021
Page 42
SPECIFICATIONS
ProComm
Power Source
AC 100-240 VAC / 45-66 Hz (10 W) Note: AC or DC must be specied at time of
ordering.
DC 10-35 VDC (10 W)
Standard Outputs
Dual 4-20mA Outputs: Galvanically isolated and fully programmable for zero and full scale
(0-21mA rangeability)
Two separate digital programmable outputs: open collector transistor usable for pulse,
frequency, or alarm settings.
• Volumetric Pulse
• Flow Rate (Frequency)
• Hardware Alarm
• High/Low Flow Alarms
• Empty Pipe
• Directional Indication
• Range Indication
• Maximum switching voltage:
40 VDC
• Maximum switching current:
100mA
• Maximum switching
frequency: 1250 Hz
• Insulation from other
secondary circuits: 500V
Optional Outputs
• Modbus
• HART
• Smart Output™(Sensus, Itron
6, Itron 9)
• Datalogger
• Built-in verification
Galvanic Isolation
All inputs / outputs are galvanically isolated from power supply up to 500 V
Engineering Units
• Cubic Meter
• Cubic Centimeter
• Milliliter
• Liter
• Cubic Decimeter
• Decaliter
• Hectoliter
• Cubic Inches
• US Gallons
• Imperial Gallons
• Cubic Feet
• Kilo Cubic Feet
• Standard Barrel
• Oil Barrel
• US Kilogallon
• Ten Thousands of Gallons
• Imperial Kilogallon
• Acre Feet
• Megagallon
• Imperial Megagallon
• Hundred Cubic Feet
• Megaliters
Conductivity
Minimum conductivity of 5µS/cm
Electrical Connections
Connection options • Compression gland seals for 0.24”to 0.47”diameter round cable
• Conduit option: 1/2”NPT threaded connections
IP Rating
IP67 Die cast aluminum converter (only when connected using compression gland seals)
PROCOMM CONVERTER SPECIFICATIONS

24511-13 Rev. 1.9 | 01FEB2021
Page 13
Specications
30124-60 Rev. 1.4 | 01FEB2021
Page 43
SPECIFICATIONS
ProComm
Certications and Approvals
Standard Model • ISO 9001:2015 certied quality management system
• CE
• Certied by MET to UL 61010-1
HL Model • ISO 9001:2015 certied quality management system
• CE
• Certied by MET to UL 61010-1 and MET C22.2 No. 61010-1-04
• Class I, Division 2, Groups A-D, T5
• Class I, Zone 2 IIC T5
I
IMPORTANT
Electrical safety certications above do not apply to model 282L Single Point
Insertion (SPI Mag) Electromagnetic Flow Meter.
I
IMPORTANT
Refer to certication requirements. Do not substitute components.
I
IMPORTANT
The ProComm converter, models PC-RA1-HL series and PC-MA1-HL series have
no user serviceable parts.
Temperature Range
Operating and
storage -4° to 140° F (-20° to 60° C)
Converter Dimensions
Remote mount • Height: 7.3” (18.5 cm)
• Width: 8.5”(21.6 cm)
• Depth: 4.3” (10.9 cm)
Meter mount • Height: 6.9”(17.5 cm)
• Width: 7.2”(18.25 cm)
• Depth: 6.2” (15.7 cm)
Keypad and Display
Can be used to access and change set-up parameters using six membrane keys and an LCD
display

24511-13 Rev. 1.9 | 01FEB2021
Page 14
SPI Mag Ordering Information
8.0 SPI MAG ORDERING INFORMATION
The standard SPI Mag includes:
• SPI Mag sensor
• ProComm converter
• 25-foot sensor cable
• Installation and Operation Manual
Options
• Extended sensor cable (up to 200’, for longer lengths, consult factory)
• Sensor insertion tool - Part No. 75031
• Additional Installation and Operation manuals - Part No. 24511-13
• RS485 Port
Returning a unit for repair
If the unit needs to be returned to the factory for repair, please do the following:
• Prior to calling for a return authorization number, determine the model number, serial number (located inside the front
panel of converter), and reason for return.
• Contact McCrometer Customer Service Department and ask for a Return Authorization (RA) number.
• Telephone: [phone]
• Email: [e-mail]
• Ship the meter in the original packaging, if possible. Do not ship manuals, power cords, or other parts with your unit
unless required for repair.
• Please make sure the meter is clean and free from foreign debris prior to shipping.
• Write the RA number on the outside of the shipping box. All return shipments should be insured.
• Address all shipments to:
McCrometer, Inc.
RA#
3255 W. Stetson Ave
Hemet, CA 92545

24511-13 Rev. 1.9 | 01FEB2021
Page 15
Conversion Tables
9.0 CONVERSION TABLES
Table of Decimal Equivalents
Table of Conversions
Fraction Decimal
1/8 .125
1/4 .25
3/8 .375
1/2 .5
5/8 .625
3/4 .75
7/8 .875
Multiply By To Get
Centimeters 0.3937 Inches
Centimeters 0.03281 Feet
Inches 25.4 Millimeters
Feet 30.48 Centimeters
Square Feet 144.0 Square Inches
Square Inches 0.006944 Square Feet
Cubic Inches 0.0005787 Cubic Feet
Cubic Feet 7.481 Gallons
Cubic Feet 1728.0 Cubic Inches
Cubic Feet 0.02832 Cubic Meters
Cubic Feet 28.32 Liters
Cubic Meters 35.31 Cubic Feet
Cubic Meters 264.2 Gallons
US Gallons 3.785 Liters
US Gallons 0.1337 Cubic Feet
US Gallons 0.003785 Cubic Meters
US Gallons .8326748 Imperial Gallons
Liters 0.2642 Gallons
ºF = (ºC x 9/5) + 32 ºC = (ºF -32) x 5/9

24511-13 Rev. 1.9 | 01FEB2021
Page 16
WARRANTY STATEMENT
WARRANTY STATEMENT
Page 3
Current as of:
McCrometer warrants that this product will be free from
defects in material and workmanship for a period 24
months from the date the equipment was rst installed,
but in no event longer than 30 months from the date the
equipment was rst shipped by McCrometer. Repairs shall
be warranted for 12 months or, if the repair is performed
under this warranty, for the remainder of the original
warranty period, whichever is less.
Buyer shall report any claimed defect in writing to
McCrometer immediately upon discovery and in any
event, within the warranty period. McCrometer shall, at its
sole option, repair the equipment or furnish replacement
equipment or parts thereof, at the original delivery point.
McCrometer shall not be liable for costs of removal,
reinstallation, or gaining access. If Buyer or others repair,
replace, or adjust equipment or parts without McCrometer
prior written approval, McCrometer is relieved of any further
obligation to Buyer under this Article with respect to such
equipment.
No equipment furnished by McCrometer shall be deemed
to be defective by reason of normal wear and tear, failure
to resist erosive or corrosive action of any uid or gas
(unless otherwise specied in Quotations/ Purchase Order
Specications), Buyer’s direct or indirect failure (or the
failure of its agents or contractors) to properly store, install,
operate, or maintain the equipment in accordance with
good industry practices or specic recommendations
of McCrometer, or Buyer’s failure to provide complete
and accurate information to McCrometer concerning the
operational application of the equipment.
THE FOREGOING LIMITED WARRANTIES WITH RESPECT
TO EQUIPMENT AND PRODUCTS ARE EXCLUSIVE AND
IN LIEU OF ANY AND ALL OTHER WARRANTIES OF
QUALITY OR PERFORMANCE, EXPRESS, IMPLIED OR
STATUTORY, INCLUDING, WITHOUT LIMITATION, ANY
AND ALL WARRANTIES OF MERCHANTABILITY OR
FITNESS OF SAID EQUIPMENT AND PRODUCTS FOR ANY
PARTICULAR PURPOSE.
MCCROMETER DISCLAIMS ANY WARRANTY, WHETHER
EXPRESS OR IMPLIED, REGARDING THE SUITABILITY
OF PRODUCTS AND EQUIPMENT SUPPLIED PURSUANT
TO ANY PURCHASE ORDER FOR INSTALLATION IN ANY
PARTICULAR SYSTEM OF SYSTEMS. MCCROMETER
MAKES NO WARRANTY OF ANY KIND WITH RESPECT TO
ANY SERVICES PERFORMED BY MCCROMETER OR ITS
AGENTS PURSUANT TO ANY QUOTATION.
Purchaser’s sole remedy and manufacturer’s sole obligation
for alleged product failure, whether under warranty
claim or otherwise, shall be the aforestated obligation of
manufacturer to repair or replace products returned within
twenty-four months after date of original shipment. The
manufacturer shall not be liable for, and the purchaser
assumes and agrees to indemnify and save harmless
the manufacturer in respect to, any loss or damage that
may arise through the use by the purchaser of any of the
manufacturer’s products.
McCrometer does not authorize any person or entity
(including, without limitation, McCrometer agents and
employees) to make any representations (verbal or
written) contrary to the terms of this limited warranty or
its exclusions. Such terms of this limited warranty and its
exclusions can only be eectively modied in writing and
only by the President of McCrometer.
SPI Mag warranty - EN 1/29/2021
2.0 MAG METERS
SPI Mag

™
DURA MAG
™
FlowConnect
OTHER McCROMETER PRODUCTS INCLUDE:
Propeller Flowmeters
Propeller Flowmeters
Dierential Pressure Flowmeters
Dierential Pressure Flowmeters
Wireless Monitoring System
Wireless Monitoring System
Magnetic Flowmeters
Magnetic Flowmeters
24511-13 Rev. 1.9 | 01FEB2021
Page 17
3255 WEST STETSON AVENUE • HEMET, CALIFORNIA 92545 USA
TEL: [phone] • 800-220-2279 • FAX: [phone]
www.mccrometer.com
Copyright © 2001-2019 McCrometer, Inc. All printed material should not be changed or altered without permission of McCrometer. Any published pricing,
technical data, and instructions are subject to change without notice. Contact your McCrometer representative for current pricing, technical data, and instructions.
Page 17