luminii Matrix Plus Series User manual

REV0.0
Matrix Plus & Matrix Mini Plus - Installation Instructions
Models MP-XX & MMP-XX
Please read all instructions prior to installation and keep for future reference!
1. Product should be installed by a qualified electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
3. Use only with Class 2 power unit. Utiliser seulement avec Classe 2 unite d’alimentation electrique.
4. Suitable for Damp Locations. Convient Aux Emplacements Humides.
5. For under-cabinet or shelf mount.
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE
Page 1 of 2
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
NOTE - Matrix can be cut into smaller sections. Matrix Plus
can be cut to 9 section or 3 sections for Matrix Mini Plus.
Refer to step 3 for details.
Remove the paper backing from the Matrix. Firmly press
down onto the aluminum heat sink. Make sure there are no air
bubbles that can cause surface irregularities. If adhesive not
sticking well to the surface. Reference step 4 to use the
mounting hardware (not included).
2
1
Attention: Always test Matrix Plus operation before installing.
Connect Matrix to power supply to ensure it is working properly
and no damage has occurred during shipping.
Matrix Plus
Matrix Plus Matrix Mini Plus
NOTE - When removing backing
& laying LineLED to surface avoid
ripples on LineLED.
paper backing
ripple
Matrix Plus
section
+
LineLED
powerfeed
connector
provided
3-pin
connector
Align Matrix power feed connector
pins with female end of Matrix and
push-in to secure connection.
If Matrix has a male end, carefully remove
the provided 3-pin connector from the Matrix
power feed connector. Align Matrix power
feed connector with male end of Matrix and
push-in to secure connection.
Matrix power feed connector can be
installed in any orientation concerning
polarity since the center pin is positive
and the two outer pins are negative.
Place the clip (CL -1) over
the connector to secure
in place
removed
3-pin
connector
clip (CL -1)
If Matrix power feed is with a 72” wire leads, proceed to wiring with power supply.
Otherwise, connect the Matrix power feed connector to the Matrix by sliding and securing
end of Matrix power feed to male or female connector. Secure by placing clip (CL-1)
over the connector and secure using the two screws. Shown below
NOTE - Provided 3-pin connector in the Matrix power feed can be removed to allow
connection to female end of Matrix Plus. See second illustration below.
+
NOTE - Plus-sign label on power feed
wire cable indicates positive polarity.
Non-marked wire cable indicates
negative polarity.
OR

REV0.0
Matrix Plus & Matrix Mini Plus - Installation Instructions
Models MP-XX & MMP-XX
Please read all instructions prior to installation and keep for future reference!
1. Product should be installed by a qualified electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
3. Use only with Class 2 power unit. Utiliser seulement avec Classe 2 unite d’alimentation electrique.
4. Suitable for Damp Locations. Convient Aux Emplacements Humides.
5. For under-cabinet or shelf mount.
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE
Page 2 of 2
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
24VDC
class II
power
supply
PURPLE
PURPLE
power feed wires
from LineLED
Connect positive wire (plus
sign tag or red wire) to
RED low voltage wire from
power supply. Also, connect
negative wire (no tag or
black wire) to PURPLE low
voltage wire from power
supply.
line voltage wires low voltage wires
Matrix Plus Matrix PlusMatrix Plus
power supply power supply
power supply
low voltage wires low voltage wires low voltage wires
+
_
RED
3-pin connector and 72” wire lead power feed wiring field-cut connector power feed wiring
power feed wires
from LineLED
Connect positive middle
wire (plus sign tag) to
RED low voltage wire
from power supply. Also,
connect BOTH negative
wires (no tags) to PURPLE
low voltage wire from
power supply.
line voltage wires low voltage wires
+
_
RED
5Always ensure power to power supply is off! Follow diagrams to connect power feed wires to power supply. Refer to power supply
instructions for wiring line voltage side.
OR
34
Matrix Plus
Matrix Plus
screw
washer
reference lines for
cutting Matrix PLus
OPTIONAL: Matrix Plus & Matrix Mini Plus can
be cut into individual sections, and orientated in
varies ways. Cut Matrix Plus board in between the
connectors to cut properly. Refer back to step 2 for
wiring Matrix Plus properly.
OPTIONAL: When the adhesive tape is not sticking on to
the surface properly. Use #0 screw size with an electrical
insulating polypropylene plastic washer 0.065’’ID, 0.188’’
OD. Insert the screw/washer through the Matrix Plus
mounting holes to secure Matrix properly to surface.
6Multiple powerfeed variations
power supplies at the end of run power supplies in the middle of run consecutive layout, NOT RECOMMENDED
24VDC
class II
power
supply
individual Matrix section