Mercedes-Benz V60 User manual

• Accessories
Installation Instructions
Mercedes-Benz V60 adaptor with
Bluetooth®wireless technology
Preliminary

Mercedes-Benz V60 adaptor with
Bluetooth®wireless technology
Page 1
1
M+P-03F-6306
Preliminary

- 1 -
The Mercedes-Benz approved/
recommended Bluetooth®Phones can be
utilized inside Mercedes-Benz vehicles.
Validity
Please contact your Mercedes-Benz Dealer
to validate if your vehicle is supported. The
vehicles need to have the Mercedes-Benz
mobile telephone kit installed and a
Mercedes-Benz-approved Bluetooth®
mobile telephone. Approved mobile
telephones are listed and can be purchased
on the Internet at www.wireless4mb.com or
call 1-800-266-7746 to speak to a wireless
activation specialist.
Parts included
•(1)M
ercedes-Benz V60 adaptor
with Bluetooth® wireless
technology
GWarning
It is not recommended to operate
the mobile telephone keypad while
driving.
Preliminary

- 2 -
Notes
The manufacturer reserves the right to
change technical details from those shown
in the illustrations contained in these
installation instructions.
These installation instructions also refer to
the vehicle Operator's Manual or the
COMAND Operator's Manual and mobile
telephone manual. Please refer to them for
reference.
Use of a mobile telephone other than a
Mercedes-Benz approved/recommended
model may result in improper performance
and cannot be supported or serviced by
Mercedes-Benz.
Preliminary

- 3 -
Inserting the Mercedes-Benz V60
adaptor with Bluetooth®
Make sure that the starter switch is in
position 1, 2 or 3 (see the vehicle Operator's
Manual).
Insert the Mercedes-Benz V60 adaptor with
Bluetooth®(1) into the connector (2) to
engage it into the cradle (3).
Note
After the adapter is inserted, the LED
button (4) will flash slowly in order to signal
that it is ready for pairing. If this does not
occur, remove the Mercedes-Benz V60
adaptor with Bluetooth®and re-insert it.
When the adapter is powered for the first
time, the LED (4) will flash fast, indicating
that it is in Discovery Mode.
3
4
1
2
M+P-03F-6307
Preliminary

- 4 -
Pairing the mobile telephone with the
Mercedes-Benz V60 adaptor with
Bluetooth®
Notes
Make sure that the starter switch is in
position 1, 2 or 3 (see the vehicle Operator's
Manual).
In order to be paired, the Mercedes-Benz
V60 adaptor with Bluetooth®must be
connected into the cradle and the LED
button (4) must be flashing slowly.
If applicable the keypad lock feature should
be disabled on the mobile telephone.
1. Press and hold the LED button (4) for
approx. 3 seconds.
The LED button (4) will begin to flash faster.
The Mercedes-Benz V60 adaptor with
Bluetooth®is now in Discovery Mode and
can be detected by a Bluetooth®mobile
telephone.
4
M+P-03F-6310
Preliminary

- 5 -
2. For information on pairing the mobile
telephone, see the mobile telephone manual
or visit www.wireless4mb.com for
instructions. The Mercedes-Benz V60
adaptor with Bluetooth®will appear as "MB
PhoneSystem" on the mobile telephone.
Once the mobile telephone detects the
Mercedes-Benz V60 adaptor with
Bluetooth®, the mobile telephone will
prompt the user for a Pass-Key.
3. Enter 62872 on the mobile telephone.
Depending on the type of mobile telephone
being used, it may be necessary to confirm a
connection request (see the mobile
telephone manual).
The LED button (4) will light up continuously,
the mobile telephone is now paired and has
stored its information in the Mercedes-Benz
V60 adaptor with Bluetooth®.
The connection between the mobile
telephone and the Mercedes-Benz V60
adaptor with Bluetooth®is established. The
connection is re-established automatically
each time the mobile telephone enters into
the Mercedes-Benz V60 adaptor with
Bluetooth®range (approx. 30 ft), as long as
the mobile telephone is switched on, the
Mercedes-Benz V60 adaptor with
Bluetooth®is enabled on the mobile
telephone, and the starter switch is in
position 1, 2 or 3 (see the vehicle Operator's
Manual).
Preliminary

- 6 -
Depending on the type of mobile telephone
being used, a message may appear in the
mobile telephone's display (see the mobile
telephone manual). The mobile telephone
will now change to hands-free mode. It is
possible to send and receive calls via the
hands-free system (see the vehicle
Operator's Manual or the COMAND
Operator's Manual.)
The Signal Strength indicator shows the
status of Mercedes-Benz V60 adaptor. This
bar display represents the following:
• 1 bar - the Bluetooth®connection is
active.
• 2 or 3 bars - there is an error in the
Bluetooth® connection.
M+P-03F-6411
M+P-03F-6412
Preliminary

- 7 -
• If the mobile telephone is connected
via Bluetooth®to the Mercedes-Benz
V60 adaptor with Bluetooth®, the
telephone home screen will be shown.
•"
No service" will be displayed, if
there is no access to the network.
Notes
If the pairing process is unsuccessful,
remove the Mercedes-Benz V60 adaptor
with Bluetooth®from the cradle (see
page 11). Re-insert the Mercedes-Benz V60
adaptor with Bluetooth®and pair it with the
mobile telephone (follow the pairing
procedure found on page 4).
A maximum of 2 mobile telephones can be
paired with the Mercedes-Benz V60 adaptor
with Bluetooth®. Only one mobile telephone
is connected to the Mercedes-Benz V60
adaptor with Bluetooth®at a time. If a third
mobile telephone is going to be paired with
the Mercedes-Benz V60 adaptor with
Bluetooth®, then the information from the
first mobile telephone paired will be deleted
from the Mercedes-Benz V60 adaptor with
Bluetooth®.
The telephone book from the mobile
telephone is automatically downloaded after
the connection, as long as this feature is
supported by the mobile telephone. For
more information, go to
www.wireless4mb.com on the Internet or
any Mercedes-Benz Center. Downloading
the telephone book can take several
minutes.
The telephone book size will vary between
vehicles.
Preliminary

- 8 -
Notes
Once the telephone book has been
downloaded any changes made to the
mobile telephone's telephone book will not
be updated in the vehicle automatically. In
order to update the telephone book press
the LED button (4) briefly (see page 4).
When using Bluetooth®the mobile
telephone uses more power. Since the
mobile telephone is not being charged the
battery should have a sufficient charge.
Neither SMS messages nor the mobile
telephone call-lists can be accessed via the
Operating System while the Bluetooth®
connection is established.
The signal strength of the mobile telephone
network is not displayed in the Instrument
cluster or radio COMAND unit.
Not every ring-tone of the mobile telephone
is supported by the COMAND or radio.
3-way-calling is not supported from the
Mercedes-Benz V60 adaptor with
Bluetooth®. An audible peep will notify a
waiting call.
The Tele Aid System (emergency call
system) will continue to function as
designed as long as there is a valid service
contract.
Before making a TELEAID call it is
recommended that any active phone call is
ended.
Preliminary