Mercia Garden Products 0619RANE0325FGSD3TW-V1 Instruction manual

2mm Drill bit
MUST CAUTION
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
TIMBER
BUILDING A BASE
TYPES OF BASE
Whilst all products manufactured are made to the highest standards of Safety and in
the case of childrens products independently tested to EN71 level, we cannot accept
responsibility for your safety whilst erecting or using this product.
Refer to the instructions pages for your specic product code
NOT
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk

Before assembly
please make sure you have a
suitable base ready to erect your
building
MADE IN GREAT BRITAIN
6
Rain Guards QTY 3
RG2844-710 (28x44x710mm)
2
1
3
4
Window QTY 3
AI-06LOGSANGTW684X1905-V1
5
Window Frame Left Upright - 71x70x2065mm QTY 3
AI-0619LOGDUFL-V3
Window Frame Right Upright - 71x70x2065mm QTY 3
AI-0619LOGDUFR-V3
Window Frame Top - 81x125x808mm QTY 3
AI-0619LOGTWTF-V3
Window Frame Bottom - 71x70x688mm QTY 3
AI-0619LOGTWBF-V3
Window Contents:
12
7
8
9
Fully Glazed
Door QTY 1
AI-06LOGSANFGMD750X1900-V1
10
11
Door Frame Left Upright - 71x70x2065mm QTY 1
AI-0619LOGDUFL-V3
Door Frame Right Upright - 71x70x2065mm QTY 1
AI-0619LOGDUFR-V3
Door Frame Bottom - 71x70x764mm QTY 1
AI-0619LOGSDBF-V3
Door Frame Top - 81x125x884mm QTY 1
AI-0619LOGSDTF-V3
Single Door Contents:
Mortice Lock
QTY1
PI-07-0017
Key Plate
QTY1
PI-07-0017
Handles (Pair)
QTY1
PI-07-0006
13 14 15 16
9 Inch T-Hinge QTY 2
PI-07-0002
Rain Guard QTY 1
RG2844-780 (28x44x780mm)

18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
17
Gable - 2500mm QTY 1
AI-0619RANE0325FGSD3TW-G
Starter Board - 19x66x2996mm QTY 2
LB19RT66-A-2996
Log Board - 19x120x237mm QTY 36
LB19-B-237
Log Board - 19x120x100mm QTY 36
LB19-C-100
Log Board - 19x120x2996mm QTY 18
LB19-A-2996
Finisher Board - 19x110x2996mm QTY 1
LB19RG110-A-2996
Log Board - 19x120x2500mm QTY 20
LB19-A-2500
Log Board - 19x120x875mm QTY 36
LB19-B-875
Roof Purlin - 40x90x3000mm QTY 3
F4090-3000
Eaves Frame - 27x44x3000mm QTY 2
F2744-3000
Fascia - 12x120x1370mm QTY 4
S16120-G-1370 (1X14° ANGLE CUT)
Fascia - 12x120x3024mm QTY 2
S12120-3024
Bearer - 44x44x2308mm QTY 2
F4444-2308-PT
Bearer - 44x44x2716mm QTY 8
F4444-2716-PT
Roof Board - 12x121x1344mm QTY 56
MB12-1344
Floor Board - 12x121x2264mm QTY 26
MB12-2264
Notched Window Gable - 2500mm QTY 1
AI-0619RANE0325FGSD3TW-GW
Log Board - 19x110x2996mm QTY 1
LB19RG110-AD-2996
Roof Spacers QTY 5
PI-07-0208 (20x100x2mm)
38
Storm Brace - 27x44x2000mm QTY 8
F2744-2000
34
35
36
Closure Trim - 16x28x2400mm (approx length) QTY 11
S1628-2400
37 Felt
Main Building Contents
Nail Bag
Felt Tacks x 200
70mm Screw x 64
40mm Screw x 394
30mm Screw x 88
60mm Bolt Set x 16
30mm Black Screw x 26
80mm Screw x 80
Pre-assembly
*Please note Each board interlocks at either end in a staggered pattern.
Before securing ensure that the boards are tted properly in their respective
tongues and grooves.

Step 1
Parts Needed - No. 30 QTY 2
No. 31 QTY 2
No’s. 30 & 31
free from
areas where standing water can
collect
8x70mm Screws
31
30
31
Pre drill
hole
70mm
screw
30
IMPORTANT: Pre-drill before xing screws.
31 31
31 31
31 31
31
30
31
Pre drill
hole
70mm
screw
Step 2
Parts Needed - No. 31 QTY 6
No.31
*Ensure there is an equal amount
of space between each frame.
24x70mm Screws
IMPORTANT: Pre-drill before xing screws.
24
24
19
19
19
Pre drill
hole
70mm
screw
IMPORTANT: Pre-drill before xing screws.
Step 3
Parts Needed - No. 19 QTY 2
No. 24 QTY 2
No’s. 19 & 24 (No. 19)
(No. 24)
4x70mm Screws

24
25
22
20
Step 4
Parts Needed - No. 20 QTY 6
No. 22 QTY 6
No. 24 QTY 6
No. 25 QTY 6
(No. 20, 22, 24 & 25)
6 boards off of the starter
boards on each side,
*Ensure that the boards are level and
ush with each other as you lay each
one.
**Please Note: The short boards at the
front/ side of the building (either side of
the door and window opening’s) can be
placed either side depending on your
needs.
IMPORTANT : Pre-drill before xing screws.
Step 5
Parts Needed - No. 2 QTY 3
No. 3 QTY 3
No. 4 QTY 3
No. 5 QTY 3
No’s. 2, 3, 4, & 5
NOT
24x80mm Screws
Pre drill
hole
80mm
screw
2
3
5
4
53

1
Pre drill
hole
80mm
screw
IMPORTANT : Pre-drill before xing screws.
Step 6
Parts Needed - No. 1 QTY 3
No. 1
*Place the frame & window at onto a level
surface to help x into place.
48x80mm Screws
IMPORTANT : Pre-drill before xing screws.
8
11
9
10
Step 7
Parts Needed - No. 8 QTY 1
No. 9 QTY 1
No. 10 QTY 1
No. 11 QTY 1
No’s. 8, 9, 10, & 11
NOT
8x80mm Screws
Pre drill
hole
80mm
screw
11 9

Step 8
Parts Needed - No. 21 QTY 18
(No.20)
**If you have not yet assembled your
window frames please refer to steps
5&6.
(No.21)
*Ensure that the boards are level
and ush with each other as you lay
each one.
a
b
a
b
21
20
Step 9
Parts Needed - No. 21 QTY 18
(No.21)
**If you have not yet assembled your
door frames please refer to step 7.
(No.21)
*Ensure that the boards are level
and ush with each other as you
lay each one.
a
ba
b
21
21

Step 10
Parts Needed - No. 20 QTY 6
No. 25 QTY 6
(No.21)
**If you have not yet assembled your
window frames please refer to steps
5&6.
(No.20 & 25)
*Ensure that the boards are level
and ush with each other as you lay
each one.
a
b
a
b
21
20
25
Step 11
(No.25)
**If you have not yet assembled your
window frames please refer to steps
5&6.
*Please note: This image is for
illustrative purposes and may differ
from your choice in product
(regarding door/window position).
Nevertheless the process of tting the
door frame is the same.

Step 12
Parts Needed - No. 20 QTY 12
No. 22 QTY 6
No. 24 QTY 6
No. 25 QTY 12
No’s. 20, 22, 24 & 25
*Ensure that the boards are
level and ush with each other
as you lay each one.
24
25
25
22
20
20
24
25
25
22
20
20
Rubber Mallet
may be required
to t parts.
Step 13
Parts Needed - No. 20 QTY 12
No. 22 QTY 6
No. 24 QTY 6
No. 25 QTY 12
No’s. 20, 22, 24 & 25
*Ensure that the boards are
level and ush with each other
as you lay each one.

23
36
Rubber Mallet
may be required
to t parts.
Step 14
Parts Needed - No. 23 QTY 1
No. 36 QTY 1
(No.23)
(No.36)
*Ensure that the boards are level
and ush with each other as you
lay each one.
Pre drill
hole
70mm
screw
17
18
Rubber Mallet
may be required
to t parts.
Step 15
Parts Needed - No. 17 QTY 1
No. 18 QTY 1
No. 17 & 18
*Ensure that the boards are level
and ush with each other as you
lay each one.
4x70mm Screws
IMPORTANT: Pre-drill before xing screws.

Pre drill
hole
70mm
screw
26 26
26
a
Step 16
Parts needed - No. 26 QTY 3
sNo. 26
ensure to
pre-drill to avoid the boards splitting
*Please note: The gable shown is for
illustrative purposes and may differ in
width from your choice in product.
Nevertheless, despite any differences the
process of xing the is the
same.
12x70mm Screws
a
b
IMPORTANT: Pre-drill before xing screws.
26
b
Rubber Mallet
may be required
to t parts.
40mm
screw
Pre drill
hole
Cut to t
Step 17
Parts needed - No. 32 QTY 56
No. 32
No. 38
*Ensure the roof boards meet at the top
of the apex and leave an overhang at
the bottom.
*Please Note: This image is for illustrative
purposes and may differ from your choice
in product. Nevertheless the process of
cutting and tting the last roof board(s) is
the same.
168 x 40mm Screws
a
b
23b 32
32
a
32
b
IMPORTANT: Pre-drill before xing screws.

30mm
screw
Pre drill
hole
27
Step 18
Parts Needed - No. 27 QTY 2
No.27
*Please Note: This image is for
illustrative purposes and may differ
from your choice in product.
Nevertheless the process of xing the
eaves frames is the same.
18x30mm Screws
IMPORTANT: Pre-drill before xing screws.
7
13
Pre drill
hole
30mm
screw
Step 19
Parts Needed - No. 7 QTY 1
No. 13 QTY 2
Once the roof is xed,
(No.7) (No.13)
(No.13)
*Ensure to screw into the framing and
not into the channel.
18x30mm Black Screws
IMPORTANT: Pre-drill before xing screws.

33
40mm
screw
Pre drill
hole
Cut to t
33
Step 21
Parts Needed - No. 33 QTY 26
No. 33
internally
*Do NOT secure the boards until the
last board has been measured and cut.
on the last
board placed
No. 33
**Please note: Mark the nal board
2mm under the measurement; This will
allow the timber to expand and contract
correctly.
***Please Note: Ensure to screw through
each of the oor boards into the oor
bearers.
208 x 40mm Screws
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
30mm
screw
Step 20
Parts Needed - No. 14 QTY 1
No. 15 QTY 1
No. 16 QTY 1
No. 15
No. 1
No. 16
No. 14
*Please note: This image is for illustrative
purposes and may differ from your choice in
product (regarding ironmongery).
Nevertheless the process of xing to the
door(s) is the same.
8x30mm Black Screws
4x30mm Screws
a
b
a
b
14
16 15
30mm
screw
IMPORTANT: Pre-drill before xing screws.

Closure Trim
Internal
23
*Measure and cut the
closure trims to
t the internal space.
Closure Trim
Internal
35
*Measure and cut the
closure trims to
t the internal space.
Pre drill
hole
30mm
screw
trim to t
Step 22
Parts needed - No. 35 QTY 6
No. 35
*Measure and cut the closure trims to
t the internal space.
36x30mm Screws
RoofRoof
IMPORTANT: Pre-drill before xing screws.
23
23
35
35
30mm
screw
Pre drill
hole
Cut to t
Step 23
Parts needed - No. 35 QTY 5
No. 35)
internally
*Do NOT x the closure trim to the oor
boards.
30x30mm Screws
IMPORTANT: Pre-drill before xing screws.
Felt
tacks
37
HANDLE
WITH CARE
12
3
4
1. 2.
3. 4.
Step 24
Parts needed - No. 37
3100mm (L) X 1000mm (W)
*Ensure there is approximately
50mm of overhanging felt each
side.
*Felt size: 3100mm x 1000mm
186x Felt Tacks

Step 25
Parts Needed: No. 6 QTY 3
No. 12 QTY 1
(No. 6)
(No. 12)
12x70mm Screws.
70mm
screw
Pre drill
hole
IMPORTANT: Pre-drill before xing screws.
Pre drill
hole
40mm
screw
29
29
28
28
28
28
IMPORTANT: Pre-drill before xing screws.
Step 26
Parts Needed - No. 28 QTY 4
No. 29 QTY 2
No’s. 28 & 29
*Ensure the angled cuts meet at the
top of the apex.
18x40mm Screws

Pre drill
hole
60mm
bolt
34
34
IMPORTANT: Pre-drill before xing screws.
Step 27
Parts needed - No. 34 QTY 8
No. 34
internally
*Ensure the storm braces are secured at
the highest point possible on each side.
**Storm braces will help your building
expand and contract properly.
***Important: Ensure each bolt is
tightened using a washer so as not to
damage the log boards.
16x60mm Bolt Sets
It is ESSENTIAL that you apply wood
treatment immediately after the building
has been assembled.