Merit Blue MAXX User manual

COPYRIGHT © 2004 MERIT INDUSTRIES, INC.
ATTENTION:
OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES
Removal/InstallationofTouchscreen-
BlueMAXX/MAXX ClassicCountertop
Touchscreen Removal
1. Turn off and unplug the game.
2. Unlock and remove the coin box or coin box/bill acceptor assembly.
3. Unlock and remove the lid by first disconnecting the fan power connector, then the clear drain-
age tubing (from lid end) and ground strap. Also remove the monitor control board attached
with velcro to the inside of the game. Then press up on the spring-loaded levers (located on
each side of the lid), push the levers forward, and lift and remove the lid. Also remove the front
bezel. See Figures 1 and 2.
4. Remove the two nuts and washers securing the touchscreen controller to the game and re-
move the controller from the mounting screws. Then disconnect the touchscreen controller
cable from the back of the controller and disconnect the Molex connector (orange and gray
wires) running from the touchscreen controller cable to the main power harness.
5. Remove the black poly tape from around the edges of the old touchscreen. Remember how
the tape was placed in order to tape the new touchscreen.
6. Use dental floss to carefully cut the foam tape holding the touchscreen to the picture tube until
you are able to completely remove the touchscreen.
7. Remove any remaining adhesive residue with denatured alcohol, then wipe the surface of the
picture tube with the supplied alcohol wipe.
Touchscreen Installation
1. Clean the reverse side of the replacement touchscreen with the supplied alcohol wipe.
2. If there is no tape already on the screen, cut pieces of the supplied 1/2” double-sided foam
tape long enough to cover each edge of the screen without overlapping. After the tape is in
place on the screen, peel off the backing.
3. Replace the new touchscreen over the picture tube (with the cable on the right if you are facing
the game), making sure the screen is properly and evenly aligned over the picture tube. Then
clean the front of the screen with the supplied alcohol wipe.
4. Rememberingthemannerin whichthe tapewas placedaround thetouchscreen youremoved,
place and cut a length of the supplied black poly tape evenly over an entire edge of the touch-
screen and repeat until all 4 edges are covered.
5. Place and cut a longer length of black poly tape around all 4 edges of the screen.
6. Route the new touchscreen controller cable under the picture tube and away from the flyback
transformer. Then reconnect the cable in the back of the controller and secure the controller
on the mounting screws in the game with the existing hardware. Also connect the Molex
connector (orange and gray wires) to the main power harness.
NOTE: Use the supplied roll of 3/8” foam tape (the thicker of the two 3/8” rolls) if you need to
replace the gasket on the inside of the front bezel. Be sure to remove all of the existing foam
tape and adhesive first.
Troubleshooting Information - Removal/Installation of Touchscreen -
Blue MAXX/MAXX Classic Countertop
Megatouch FORCE Technical Reference Manual

COPYRIGHT © 2004 MERIT INDUSTRIES, INC.
FIGURE 1 - BLUE MAXX/MAXX CLASSIC - HOOD ASSEMBLY
FAN POWER
CONNECTOR
CLEAR
DRAINAGE
TUBING
SPRING-LOADED
LEVER
GROUND
STRAP
ATTENTION:
OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES
Removal/InstallationofTouchscreen-
BlueMAXX/MAXX ClassicCountertop
Troubleshooting Information - Removal/Installation of Touchscreen -
Blue MAXX/MAXX Classic Countertop
Megatouch FORCE Technical Reference Manual
7. After replacing the front bezel, install the lid on the chassis, connecting the fan power connec-
tor, monitor control board, ground strap, and plastic drain tube. Then pull the lid towards you
until the spring-loaded levers lock into place. See Figures 1 and 2 for locations.
8. Close and lock the lid.
9. Plug in and turn on the game.
10. When the game is finshed booting, calibrate the touchscreen.
11. Replace and lock the coin box or coin box/bill acceptor assembly.

COPYRIGHT © 2004 MERIT INDUSTRIES, INC.
FIGURE 2 - BLUE MAXX/MAXX CLASSIC - MONITOR ASSEMBLY
FRONT
BEZEL
Troubleshooting Information - Removal/Installation of Touchscreen -
Blue MAXX/MAXX Classic Countertop
Megatouch FORCE Technical Reference Manual