Metra Electronics 95-5026 User manual

INSTALLATION INSTRUCTIONS FOR PART 95-5026
1-800-221-0932 www.metraonline.com
©COPYRIGHT 2004 METRA ELECTRONICS CORPORATION
KIT FEATURES
•Double DIN head unit provision
•Stacked ISO DIN head unit provision
A) DDIN Trim Plate | B) DDIN Brackets | C) Rear Support Bracket
KIT COMPONENTS
TOOLS REQUIRED:
95-5026
AB
APPLICATIONS
2001-2004 Ford Mustang
2003-2006 Ford Expedition
2002-2005 Ford Explorer
2003-2006 Lincoln Navigator
2002-2005 Lincoln Aviator
2002-2005 Mercury Mountaineer
Phillips Screwdriver I Socket wrench
C

TABLE OF CONTENTS
95-5026
Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

95-5026
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unclip and remove shift lever trim
panel. (Figure A)
2
2001-2004 FORD MUSTANG
Unclip and remove the entire panel
surrounding the radio and climate
controls including the vents.
(Figure B)
3
Remove (2) 9/32” screws securing
radio. (Figure B)
4
DASH DISASSEMBLY
A
B

95-5026
2
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Remove (2) 9/32” screws from above
instrument cluster. (Figure A)
2
2003-2006 FORD EXPEDITION
Unclip and remove entire panel sur-
rounding radio, climate controls, and
instrument cluster.
(Figure B)
3
Remove (2) 9/32” screws securing
radio.
4
DASH DISASSEMBLY
A
B

95-5026
3
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unclip and remove entire panel sur-
rounding radio including climate con-
trols and vents.
(Figure A)
2
2002-2005 FORD EXPLORER
2002-2005 MERCURY MOUNTAINEER
Remove (2) 9/32” screws securing
radio.
(Figure B)
3
DASH DISASSEMBLY
B
A

4
95-5026
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Open center console and remove (1)
push pin from back of power window
switch panel.
(Figure A)
2
2003-2006 LINCOLN NAVIGATOR
Unclip and remove panel.
3
Remove (2) 9/32” screws exposed
on shifter panel then unclip and
move shifter panel off to side.
(Figure B,C)
4
Remove (2) 9/32” screws exposed
under ashtray assembly. (Figure C)
5
Unclip and remove entirepanel sur-
rounding climate controls and radio.
6
Remove (2) 9/32” screws securing
radio.
(Figure C)
7
DASH DISASSEMBLY
INSIDE CENTER CONSOLE
TOP VIEW
TOP OF SHIFTER TRIM PANEL
5
4
7
7
A
B
C

5
95-5026 DASH DISASSEMBLY
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unclip and remove vent panel above
radio on top of dashboard. (Figure A)
2
2003-2005 LINCOLN AVIATOR
Remove (2) 9/32” screws exposed
under panel removed in step 1.
(Figure B)
3
Unclip and remove panel around
radio with door in it.
(Figure C)
4
Unclip and remove vents below
radio.
Figure D)
5
Remove (2) 9/32” screws securing
radio.
(Figure E)
6
A
B
C
D
105.9
E

95-5026
KIT ASSEMBLY
6
2
A
Slide the DDIN radio unit into the
trim plate bracket assembly and
secure the unit to the kit using the
screws supplied with the head unit.
(
Figure B)
3
Position the rear support bracket
with slide grooves facing down and
secureto the backof the aftermar-
ket radio with the hardware supplied
with aftermarket head unit.
(
Figure C)
Slide the appropriate bracket into
the trim plate aligning the holes in
the trim plate to the clips on the
bracket. (
Figure A)
1
B
C
DOUBLE DIN HEAD UNIT PROVISION

95-5026
KIT ASSEMBLY
7
2
A
Slide the stacked ISO DIN units into
the trim plate bracket assembly and
secure the units to the kit using the
screws supplied with the head units.
(
Figure B)
3
Position the rear support bracket
with slide grooves facing down and
secure to the back of the aftermar-
ket radio with the hardware supplied
with aftermarket head unit.
(
Figure C)
Slide the appropriate bracket into
the trim plate aligning the holes in
the trim plate to the clips on the
bracket. (
Figure A)
1
B
B
STACKED ISO DIN HEAD UNIT PROVISION

95-5026
FINAL ASSEMBLY
8
FINAL ASSEMBLY
1
Locate the factory wiring harness in the dash and make the connection as shown.
Metra recomends using the proper mating adapter and making the connections as
shown. (Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
2
Re-connect the negative battery terminal and test the unit for proper operation.
3
Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS