Metra Electronics 95-5817 User manual

INSTALLATION INSTRUCTIONS FOR PART 95-5817
95-5817
KIT FEATURES
•A) Double Din Trim Brackets • B) Filler Bar
KIT COMPONENTS
Dremel or Suitable Cutting Tool • Small Flat Blade Screwdriver
•Panel Removal Tool • Socket Wrench
• Metra 86-5618 Removal Keys
1-800-221-0932
©COPYRIGHT 2009-10 METRA ELECTRONICS CORPORATION
www.metraonline.com
A
APPLICATIONS
•Double DIN Unit Provision
•Stacked ISO Mounts Units Provision
NOTE: Sub dash modifications are
necessaryto use this dash kit.
You will need to trim the sub dash
to gain suitable depth and height.
NOTE: Once the kit is snapped in, it cannot be
removed without dash panel removal.
B
TOOLS REQUIRED:
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
•See www.metraonline.com for specific interface
applications
Antenna Adapter: Not required.
FORD
Explorer 1995-2001
Explorer Sport Trac 2001-2005
Ranger 1995-2009
Crown Victoria 1995-2009
Econoline 1997-2008
Escape 2001-2007
Windstar 1999-2003
Excursion 2000-2005
Super Duty 1999-2004
LINCOLN
Continental 1995-1997
Mark VIII 1996-1998
Town Car 1995-2002
MAZDA
B-Series Pickup 1995-2009
MERCURY
Grand Marquis 1995-2009
Marauder 2003-2004
Mountaineer 1997-2001
Mariner 2005-2007

Dash Disassembly
-All Vehicles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Assembly
-Double DIN/Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . 2
Final Assembly .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
TABLE OF CONTENTS
95-5817
*Note:
Refer also to the instructions included with the aftermarket radio.
K NOWLEDGE IS P OWER
Enhanceyour installation and fabrication skillsby
enrolling in the most recognizedandrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.comor call
800-354-6782 for more informationandtake steps
toward abetter tomorrow.

95-5817 DASH DISASSEMBLY
1
1
Using the Metra 86-5618 removal keys, slide the radio out of the radio cavity.
Unplug and remove the radio. ( Figure A)
Disconnect the negative battery terminal to prevent an accidental short circuit.
2
Cut and remove obstructions in dash cavity. (Be careful not to cut into harnesses or
electronic components)
3
Continue to kit assembly.
ALL VEHICLES

95-5817 KIT/FINAL ASSEMBLY
2
DOUBLE DIN/STACKED ISO MOUNT
UNIT(S) PROVISION
Attach the double DIN brackets to
the double DIN or stacked ISO Mount
unit(s) using the screws supplied
with the unit(s).
(Figure A)
1
*Note: Refer also to the instructions included with the aftermarket radio.
A
B
NOTE: Sub dash modifications arenecessaryto use this dash kit. You will need to
trim the sub dash to gain suitable depth and height.
A
B
C
D
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter and mak-
ing the connections as shown.
(Isolate and individually tape off the
ends of any unused wires to prevent
electrical short circuit).
(Figure B)
Re-connect the negative battery terminal
and test the unit for proper operation.
2
3
Continued on page 3.
NOTE: Once the kit is snapped in, it cannot be removed without dash panel removal.

95-5817 KIT/FINAL ASSEMBLY
FINAL ASSEMBLY
Makewiring connections using the EIA color code chart shown below and the instructions
included with the head unit. Metra recommends making connections shown below; Strip, Splice,
Solder, Tape.Isolate and individually tape off ends of any unused wires to prevent electrical short
circuit.
3
FINAL WIRING CONNECTIONS
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna............Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer.................Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE:
When a Blackwireis not present, ground radio to vehicle chassis. All colors may not be
present on all leads due to manufacturer’sspecifications.
Enjoy your newly installed radio!
NOTE: Major sub dash modifications arenecessaryto use this dash kit. You will
need to trim the sub dash to gain suitable depth and height.
Slide the double DIN radio or stacked
ISO Mount unit assembly into the
modified sub dash until it clicks into
place.
4
Clip the filler bar into the bottom of
the radio opening under the radio
assembly with the rounded edges
facing toward the dash. Tip: Hook
one side in then push the other side
in until it clips. (Figure C)
5
C
Continued from page 2.

NOTES
4
95-5817

NOTES
5
95-5817

95-5817 INSTRUCTIONS
1-800-221-0932
REV.06/08/10 © COPYRIGHT 2009-10 METRA ELECTRONICS CORPORATION INST95-5817
www.metraonline.com