Metra Electronics 99-7339B User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7339
APPLICATIONS
HYUNDAI GENESIS COUPE 2.0
2010
KIT FEATURES
•ISO Head Unit Provision with Pocket
•Painted to match factory finish
99-7339B=Black 99-7339S=Silver
A) Trim Panel B) ISO Brackets C) Pocket D) (6) PC-7503 Panel Clips E) (4) 3/8” Phillips Screws
KIT COMPONENTS
A
TOOLS REQUIRED:
•Small Flat Blade Screwdriver • Phillips Screwdriver
•Panel Removal Tool • Socket Wrench
1-800-221-0932
©COPYRIGHT 2007-2010 METRA ELECTRONICS CORPORATION
www.metraonline.com
99-7339S
99-7339B
BCD
E
METRA. THE WORLD’S BEST KITS.™
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
•70-7303 - Kia/Hyundai Harness 2009 -up
Antenna Adapter:
•40-KI11 - Kia/Hyundai Antenna Adapter 2007-up

Dash Disassembly
-Hyundai Genesis Coupe 2010 . . . . .......................... 1
Kit Preparation
-Hyundai Genesis Coupe 2010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Kit Assembly
-ISO DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
TABLE OF CONTENTS
99-7339
*Note:
Refer also to the instructions included with the aftermarket radio.
K NOWLEDGE IS P OWER
Enhanceyour installation and fabrication skillsby
enrolling in the most recognizedandrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.comor call
800-354-6782 for more informationandtake steps
toward abetter tomorrow.
Metra recommends MECP certified
technicians.

99-7339 DASH DISASSEMBLY
HYUNDAI GENESIS COUPE 2010
A
B
C
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unclip and remove the shifter trim
panel. ( Figure A)
2
Unclip and remove the radio/climate
control trim panel. (Figure B)
3
Unclip and remove the display trim
panel above radio.
(Figure C)
4
Remove (4) Phillips screws securing
the radio.
5
Remove (4) Phillips screws securing
the climate control to the factorytrim
panel.
6

99-7339 KIT PREPARATION
2
A
B
KIT PREPARATION
Continue to kit assembly
HYUNDAI GENESIS COUPE 2010
Attach the climate control to the 95-
7336S trim plate using the factory
hardware. (Figure A)
1
Attach the (6) panel clips to the 95-
7336S trim plate. (Figure B)
2

99-7339 KIT ASSEMBLY
A
B
3
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
1
Attach the ISO brackets to the after-
market radio (figure A), then secure
the assembly to the pocket using the
(4) supplied Phillips screws (figure B).
2
Mount the assembly into the sub
dash.
3
Reassemble dash in reverse order of
disassembly using the 99-7339 trim
panel instead of the factory trim
panel.
4
HYUNDAI GENESIS COUPE 2010
ISO DIN HEAD UNIT PROVISION

NOTES
99-7339

NOTES
99-7339

306
INSTRUCTIONS
1-800-221-0932
REV. 12/15/09 © COPYRIGHT 2003-2010 METRA ELECTRONICS CORPORATION INST99-7339
www.metraonline.com
99-7339 INSTRUCTIONS
METRA. THE WORLD’S BEST KITS.™