Metra Electronics 95-8210 User manual

INSTALLATION INSTRUCTIONS FOR PART 95-8210
APPLICATIONS
Toyota 4-Runner Limited
2003-2009
KIT FEATURES
•Double DIN Radio Provision
•Stacked ISO Mount Units Provision
A) Double Din Trim Plate • B) Double DIN Brackets
KIT COMPONENTS
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver • Socket Set
1-800-221-0932
©COPYRIGHT 2007-2009 METRA ELECTRONICS CORPORATION
www.metraonline.com
B
95-8210
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
• 70-1761 - Toyota harness 1987-up
•TYTO-01 - Toyota amp harness 2003-UP
Antenna Adapter:
•Not required

Dash Disassembly
- Toyota 4-Runner Limited 2003-2009 . . . . . . . . . . . . . . . . . 1,2
Kit Assembly
-Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
-Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Final Assembly ........................................... 5
TABLE OF CONTENTS
95-8210
*Note:
Refer also to the instructions included with the aftermarket radio.
K NOWLEDGE IS P OWER
Enhanceyour installation and fabrication skillsby
enrolling in the most recognizedandrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.comor call
800-354-6782 for more informationandtake
steps towardabetter tomorrow.

95-8210 DASH DISASSEMBLY
Toyota 4-Runner Limited 2003-2009
A
B
C
D
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unsnap and remove trim from around
shifter. ( Figure A)
2
Unsnap and remove center console
cover. (Figure B)
3
Unsnap trim ring from around ignition
key cylinder.
4
Remove (1) 10 mm bolt from bottom
right side of panel below steering col-
umn. Unsnap panel and pull away to
gain access behind panel. ( Figure C)
5
Remove (1) 10 mm bolt on bottom left
of center panel behind panel below
steering column. ( (Figure D)
6

95-8210 DASH DISASSEMBLY
Toyota 4-Runner Limited 2003-2009
E
F
PASSENGER
G
H
2
Remove (1) 10 mm bolt beneath cli-
mate control behind pocket door.
(Figure E) Unsnap climate control,
unplug and remove climate control.
(Figure F)
7
Remove (2) 10 mm bolts beneath
radio behind climate controls.
(Figure G)
8
Unsnap and remove entire center
panel around radio.
9
Remove (2) 10 mm bolts securing
radio. Unplug and remove radio.
(Figure H)
10
Continue to final assembly.

95-8210 KIT ASSEMBLY
3
B
A
C
DOUBLE DIN RADIO PROVISION
Snap the Double DIN brackets to the
outside edge of the Double DIN trim
plate. (Figure B)
2
Snap the factory brackets to the side
of the radio.
(Figure A)
1
Slide the Double DIN radio into the
bracket/trim plate assembly and
secure the radio to the assembly
using the screws supplied with the
radio.
(Figure C)
3
Continue to final assembly.
* Note: Refer also to the instructions included with the aftermarket radio.

95-8210 KIT ASSEMBLY
4
B
A
C
STACKED ISO UNITS PROVISION
Snap the Double DIN brackets to the
outside edge of the Double DIN trim
plate.
(Figure B)
2
Slide the stacked ISO mount units into
the bracket/trim plate assembly and
secure the units to the assembly
using the screws supplied with the
units.
(Figure C)
3
Continue to final assembly.
* Note: Refer also to the instructions included with the aftermarket radio.
Snap the factory brackets to the side
of the radio.
(Figure A)
1

95-8210 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground..................Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
5

95-8210 INSTRUCTIONS
1-800-221-0932
REV. 06/03/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION INST95-8210
www.metraonline.com