Metra Electronics 99-8201 User manual

KIT COMPONENTS
TOOLS REQUIRED
Cutting tool
Socket wrench
Phillips screwdriver
KIT FEATURES
ISO-DIN
head unit
provisions
Pocket
provisions
99-8201
INSTALLATION
INSTRUCTIONS
APPLICATIONS
CAR PAGE
TOYOTA
Celica 2000-05................................................1-3
Echo 2000-05..................................................1-3
Radio
Housing
"C"
Radio
Housing
"E"
Mounting
Brackets
Re-connect the battery terminal and test the unit
for proper operation. Mount the head unit/kit
assembly to the sub-dash with (4) screws
previously removed in step #1.
76
Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adaptor and making
connections as shown. (Isolate and
individually tape off the ends of any
unused wires to prevent electrical short
circuit).
A
B
C
D
A) Strip wire ends back ½"
B) Twist ends together
C) Solder
D) Tape
(6) #6 x ¼"
Phillips Flat-
5
Align the holes in the Mounting Brackets with the holes in the ISO-DIN head unit and mount
the Brackets to the head unit with the screws included with the unit.
3
Pocket
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2001-07 METRA ELECTRONICS CORPORATION
rev. 06-15-07

2
1
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip and
remove the gear shifter trim bezel and remove (2)
Phillips screws exposed below the climate
controls. Pull off climate control knobs and
remove (2) Phillips screws exposed. Unclip the
climate control/factory radio trim bezel and
remove. Remove (4) 10mm screws securing the
factory head unit and disconnect the wiring.
Locate Radio Housing "C". Using the
dotted lines as a guide, cut and remove
all tabs on the Mounting Brackets
EXCEPT tabs "C". Skip to the
Installation Instructions for ALL
VEHICLES on Page #2.
Locate Radio Housing "E". Using the
dotted lines as a guide, cut and remove
all tabs on the Mounting Brackets
EXCEPT tabs "E". Skip to the
Installation Instructions for ALL
VEHICLES on Page #2.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove the
climate control knobs and (2) Phillips screws
exposed. Unclip and remove the climate control
trim bezel. Depress the side clips securing the
climate control panel and move the panel to
access (2) Phillips screws from the top of the
factory radio brackets. Remove the ashtray.
Unclip and remove the radio trim bezel. Remove
(2) Phillips screws from the bottom of the radio
brackets and disconnect the wiring.
1
1
TOYOTA Celica 2000-05 ALL VEHICLES
TOYOTA Echo 2000-05
3
4
Snap the Pocket onto the back of the Radio Housing.
Attach the Mounting Brackets to the sides of the Radio Housing by inserting the slotted
Bracket tabs into the slotted Housing tabs. (Be sure the mounting bosses on the Brackets
align with the mounting bosses on the Pocket ). Mount the Brackets to the Pocket with (6) #6 x
¼" Phillips Flat-Head Screws.
2
2
"C"
"E"
"E"
"C"
CUT
CUT
CUT
CUT
CUT

2
1
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip and
remove the gear shifter trim bezel and remove (2)
Phillips screws exposed below the climate
controls. Pull off climate control knobs and
remove (2) Phillips screws exposed. Unclip the
climate control/factory radio trim bezel and
remove. Remove (4) 10mm screws securing the
factory head unit and disconnect the wiring.
Locate Radio Housing "C". Using the
dotted lines as a guide, cut and remove
all tabs on the Mounting Brackets
EXCEPT tabs "C". Skip to the
Installation Instructions for ALL
VEHICLES on Page #2.
Locate Radio Housing "E". Using the
dotted lines as a guide, cut and remove
all tabs on the Mounting Brackets
EXCEPT tabs "E". Skip to the
Installation Instructions for ALL
VEHICLES on Page #2.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove the
climate control knobs and (2) Phillips screws
exposed. Unclip and remove the climate control
trim bezel. Depress the side clips securing the
climate control panel and move the panel to
access (2) Phillips screws from the top of the
factory radio brackets. Remove the ashtray.
Unclip and remove the radio trim bezel. Remove
(2) Phillips screws from the bottom of the radio
brackets and disconnect the wiring.
1
1
TOYOTA Celica 2000-05 ALL VEHICLES
TOYOTA Echo 2000-05
3
4
Snap the Pocket onto the back of the Radio Housing.
Attach the Mounting Brackets to the sides of the Radio Housing by inserting the slotted
Bracket tabs into the slotted Housing tabs. (Be sure the mounting bosses on the Brackets
align with the mounting bosses on the Pocket ). Mount the Brackets to the Pocket with (6) #6 x
¼" Phillips Flat-Head Screws.
2
2
"C"
"E"
"E"
"C"
CUT
CUT
CUT
CUT
CUT

KIT COMPONENTS
TOOLS REQUIRED
Cutting tool
Socket wrench
Phillips screwdriver
KIT FEATURES
ISO-DIN
head unit
provisions
Pocket
provisions
99-8201
INSTALLATION
INSTRUCTIONS
APPLICATIONS
CAR PAGE
TOYOTA
Celica 2000-05................................................1-3
Echo 2000-05..................................................1-3
Radio
Housing
"C"
Radio
Housing
"E"
Mounting
Brackets
Re-connect the battery terminal and test the unit
for proper operation. Mount the head unit/kit
assembly to the sub-dash with (4) screws
previously removed in step #1.
76
Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adaptor and making
connections as shown. (Isolate and
individually tape off the ends of any
unused wires to prevent electrical short
circuit).
A
B
C
D
A) Strip wire ends back ½"
B) Twist ends together
C) Solder
D) Tape
(6) #6 x ¼"
Phillips Flat-
5
Align the holes in the Mounting Brackets with the holes in the ISO-DIN head unit and mount
the Brackets to the head unit with the screws included with the unit.
3
Pocket
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2001-07 METRA ELECTRONICS CORPORATION
rev. 06-15-07