Metra Electronics 99-8204 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-8204
Socket Wrench • Phillips Screwdriver
1-800-221-0932 www.metraonline.com
KIT FEATURES
©COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION
•DDIN Head Unit Provision with Pocket
•ISO DIN Head Unit Provision with Pocket
A) Radio Housing • B) Pocket • C) Trimplate • D) Mounting Brackets • E) ISO Brackets • F) Rear Support Bracket
G) (8) #8x3/8” Phillips Flat Head Screws • H) (4) #8x3/8” Phillips Pan Head Screws
KIT COMPONENTS
TOOLS REQUIRED:
99-8204
APPLICATIONS
2003-2008 Toyota Corolla
ABCD
EFG H

Dash Disassembly ............................................................................ 1
Kit Assembly ................................................................................. 2-3
Final Assembly ................................................................................. 4
99-8204
TABLE OF CONTENTS

1
2003-2008 TOYOTACOROLLA
99-8204 DASH DISASSEMBLY
Disconnect the negative battery terminal to prevent an accidental short circuit. Unsnap the
gear shifter trim bezel and remove. Remove the center climate control knob and (1) Phillips
screw exposed. Unclip the climate control bezel/pocket assembly and remove. Remove (4)
10 mm bolts from the bottom of the factory head unit. Remove the factory head unit/trim
bezel assembly and disconnect the wiring. Unclip the bezel from the head unit and remove
the unit.

2
99-8204 KIT ASSEMBLY
2003-2008 TOYOTACOROLLA
Attach the Pocket to the back of the Radio Housing (by holding the Housing upside-down,
inserting the right edge of the Pocket into place and pushing the rest of the Pocket onto the
lip) and mount with (2) #8 x 3/8" Phillips Pan-head Screws supplied. Secure the
Mounting Brackets to the Pocket with (8) #6 x 1/4" Phillip Flat-head Screws supplied.
Mount the Rear Support Bracket to the back of the Pocket with (2) #8 x 3/8" Phillips
Pan-head Screws supplied.

3
1
A
ISO DIN HEAD UNIT PROVISION
1
2
B1
"A"
"B"
B2
B3
99-8204 KIT ASSEMBLY
Slide the DIN cage into the Radio Housing
and secure by bending the metal locking
tabs down. Slide the aftermarket head
unit into the cage and secure.
Align the holes in the ISO Brackets mount
the Brackets to the head unit with the
screws supplied with the unit. Slide the
head unit/bracket assembly into the radio
opening until the side clips engage and
snap the Trimplate over the unit.
(See Fig. B1)
Re-connect the batteryterminal and test
the unit for proper operation. Snap the
factory head unit trim bezel over the kit by
engaging the (4) bracket tabs ("A") and
(3) Housing bosses ("B") to the back of
the bezel. Slide the assembly into the sub-
dash and mount with (4) 10 mm bolts pre-
viously removed in step #1. Re-assemble
the dash. (See Fig. B3)
NOTE: To remove the mounted head unit,
unclip and remove the ISO Trimplate.
Using a small flat-blade screwdriver, dis-
engage the side clips securing the ISO
Brackets to the Radio Housing.
(See Fig. B2)
DIN HEAD UNIT PROVISION

4
1
Locate the factory wiring harness in the dash and make the connection as shown.
Metra recomends using the proper mating adapter and making the connections as
shown. (Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
2
Re-connect the negative battery terminal and test the unit for proper operation.
3
Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of anyunused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’sspecifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS
FINAL ASSEMBLY
99-8204 FINAL ASSEMBLY

5
99-8204
NOTES

99-8204 INSTRUCTIONS
1-800-221-0932 www.metraonline.com
©COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION INST99-8204
REV. 10/02/07