Metra Electronics 99-2005 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-2005
Small Flat Blade Screwdriver • Panel Removal Tool
•Phillips Screwdriver • Socket Wrench
1-800-221-0932 www.metraonline.com
KIT FEATURES
©COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION
APPLICATIONS
CADILLAC
ELDORADO 1996-2002
SEVILLE 1996-2005
DEVILLE 2000-2005
DEVILLE CONCOURS (CONSOLE SHIFT)1996-1999
•DIN Mount Radio Provision with Pocket
•ISO Mount Radio Provision with Pocket
•A) Radio Housing • B) Radio Housing Brackets • C) ISO Brackets • D) ISO Trim Plate • E) Spacer
•F) (4) Phillips Screws
KIT COMPONENTS
99-2005
B
C
F
D
98-04S
A
E
S-E
TOOLS REQUIRED:

• Dash Disassembly
-Cadillac Eldorado 1996-2002------------------------------------- 1
-Cadillac Seville 1996-1997--------------------------------------- 1
-Cadillac Seville 1998-2005--------------------------------------- 2
-Cadillac Deville 2000-2005--------------------------------------- 3
-Cadillac Deville Concours (Console Shift) 1996-1999----------- 2
• Kit Assembly
-Cadillac Eldorado 1996-2002------------------------------------ 4
-Cadillac Seville 1996-1997--------------------------------------- 4
-Cadillac Seville 1998-2005 --------------------------------------- 5
-Cadillac Deville 2000-2005--------------------------------------- 6
-Cadillac Deville Concours (Console Shift) 1996-1999----------- 5
- DIN Mount Radio Provision --------------------------------------- 7
-ISO Mount Radio Provision--------------------------------------- 7
• Final Assembly ----------------------------------------------------- 8
TABLE OF CONTENTS
99-2005
*Note: Refer also to the instructions included with the aftermarket radio.
K NOWLEDGE IS P OWER
Enhanceyour installation and fabrication skillsby
enrolling in the most recognizedandrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.comor call
800-354-6782 for more informationandtake steps
toward abetter tomorrow.

1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
Remove C-clip on forward facing side of
shift knob and pull and remove knob.
(Figure A)
1
2
Remove (2) 9/32 screws on each side of
the ashtray assembly and (1) in the mid-
dle underneath ashtray insert. (Figure B)
3
Remove the (6) retaining nuts securing
the radio and climate control to the facto-
ry bracket assembly and slide the climate
control outward. (Figure F)
6
Insert a small flat blade screwdriver in
between the radio and the switch panel at
top of radio and pry up and out to remove
switch panel. (Figure C)
4
Remove (4) 9/32 screws
•(2) from the top (Figure D) and
•(2) from the bottom to remove radio.
(FigureE)
5
A
B
C
D
CADILLACELDORADO 1996-2002
CADILLACSEVILLE 1996-1997
99-2005 DASH DISASSEMBLY
Continue to kit assembly
E
Remove 3Retaining Nuts
Per Side
F

2
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
Insert a small flat blade screwdriver in
between the radio and the switch panel
at top of radio and pryup and out to
remove switch panel. (Figure B)
1
3
Remove (3) 9/32 screws
•(1) from the top (Figure C) and
•(2) from the bottom to remove radio.
(Figure D)
4
Remove the (6) retaining nuts securing
the radio and climate control to the fac-
torybracket assembly and slide the cli-
mate control outward. (Figure E)
5
Remove (2) 9/32 screws on each side of
the ashtray assembly and (1) in the mid-
dle underneath ashtray insert. (Figure A)
2
99-2005 DASH DISASSEMBLY
Continue to kit assembly
CADILLACSEVILLE 1998-2005
CADILLACDEVILLE CONCOURS
(CONSOLE SHIFT) 1996-1999
A
B
C
D
Remove 3Retaining Nuts
Per Side
E

Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
Unsnap and remove panel surrounding
climate controls and radio. (Figure A)
1
2
Depress clips on both sides of radio and
pull out to remove. (Figure B)
3
CADILLACDEVILLE 2000-2005
3
99-2005 DASH DISASSEMBLY
Continue to kit assembly
A
B

4
99-2005 KIT ASSEMBLY
Remove all tabs except the ones marked
S-E from the radio housing. (Figure A)
Slide the climate control assembly into
the bracket / housing assembly and
attachwith the factoryhardware.
(FigureC)
1
3
Slide the S-E radio housing bracket onto
the 99-2005 until side clips engage.
(Figure B)
2
CADILLACELDORADO 1996-2002
CADILLACSEVILLE 1996-1997
S-E
S-E
D
D
D
D
98-04 S
98-04 S
98-04 S
A
B
C
Continue to kit assembly

5
99-2005 KIT ASSEMBLY
S-E
S-E
D
D
D
D
98-04 S
98-04 S
98-04 S
A
B
C
D
Slide the climate control assembly into
the bracket / housing assembly and
attach with the factory hardware.
(Figure C)
3
When DIN mounting slide the included
spacer onto the DIN cage that came with
your aftermarket radio before inserting it
into the housing. (Figure D)
4
Remove all tabs except the ones marked
98-04 S from the radio housing.
(Figure A)
1
Slide the 98-04 S radio housing bracket
onto the 99-2005 until side clips engage.
(Figure B)
2
Continue to kit assembly
CADILLACSEVILLE 1998-2005
CADILLACDEVILLE CONCOURS
(CONSOLE SHIFT) 1996-1999
NOTE: In order to DIN mount in the 2000-2004 Deville you will need to use the provided
spacer as described below. There is not enough depth to ISO mount or DIN mount without
the spacer.

6
99-2005 KIT ASSEMBLY
CADILLACDEVILLE 2000-2005
NOTE: In order to DIN mount in the 2000-2004 Deville you will need to use the provided
spacer as described below. There is not enough depth to ISO mount or DIN mount without
the spacer.
S-E
S-E
D
D
D
D
98-04 S
98-04 S
98-04 S
A
B
C
Remove all tabs except the ones marked
Dfrom the radio housing. (Figure A)
When installing the 99-2005 housing into
the sub dash, use the supplied (4) phillips
screws and mount in the locations shown
(FigureC)
1
3
When DIN mounting slide the included
spacer onto the DIN cage that came with
your aftermarket radio before inserting it
into the housing. (FigureB)
2
Continue to kit assembly

7
DIN HEAD UNIT PROVISION
99-2005
KIT ASSEMBLY
NOTE: Refer also to the instructions included with the aftermarket radio.
2
1Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down.
(Figure A)
Slide the after-market head unit into
the cage and secure.
(Figure B)
A
B
Continue to kit assembly

8
ISO DIN HEAD UNIT PROVISION
99-2005
KIT ASSEMBLY
NOTE: Refer also to the instructions included with the aftermarket radio.
2
Snap the Trim plate into the Radio
Housing.
(Figure B)
1Mount the ISO brackets to the after-
market radio with the screws
supplied with the unit.
(Figure A)
Slide the after-market radio unit into
the cage and secure. (Figure B)
3
A
B
Continue to kit assembly