Metra Electronics 99-3309B User manual

APPLICATIONS
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
Installation instructions for 99-3309B
• ISODINradioprovisionwithpocket
• DoubleDINradioprovision
• InterfaceincludedretainsfactoryOnStar,Bluetooth,and
allwarningchimes
• Providesa12-voltaccessorypowerandVSS,parking
brake,andreversesignals
• Painted matte black
•A)Radiotrimpanel•B)Radiobrackets•C)Pocket•D)(4)#8x3/8”Phillipsscrews•E)(10)Whiteplastic
panelclips•F)Interface•G)16-pinharness•H)4-pinto4-pinresistorpad•I)22-pinto44-pinharness
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS(soldseparately)
WiringHarness:
• Interfaceincluded
AntennaAdapter:
• 40-EU55
• Panelremovaltool•Phillipsscrewdriver
• Smallflat-bladescrewdriver
TOOLS REQUIRED
Chevrolet Spark 2013-up
99-3309B
See application list inside
A B C
F G H I
D E

99-3309B Dash Disassembly 99-3309B
1. Unclipandremovetheradio
trimpanel.(FigureA)
2. Remove(4)Phillipsscrews
securingthefactoryradio
andremovefromdash.
(FigureB)
3. Unclipandremovethevents
fromthefactorypanel.
(FigureC)
4. Unclipandremovethe
hazardbuttonfromthetrim
panel.(FigureC)
5. Remove(5)Phillipsscrews
securingtheupperdisplay
shroudfromthefactory
panel.(FigureC)
Continue to kit assembly
(Figure A) (Figure B)
Chevrolet Spark 2013-up
(Figure B)
Step 3
Step 5
Step 4
Step 5

Kit Assembly 99-3309B
ISO DIN radio provision with pocket
1. Attachthefactoryventsandhazard
buttontotheMetratrimpanel.
(FigureA)
2. Attachtheupperdisplayshroudthe
Metratrimpanelwiththefactory
screws.(FigureA)
3. Attachtheprovided(10)panelclipsto
thelegsoftheMetratrimpanel.
4. Locatethefactorywiringharnessin
thedash.Metrarecommendsusing
thepropermatingadapterfromMetra
orAXXESS.Re-connectthenegative
batteryterminalandtesttheunitfor
properoperation.
5. Attachtheradiobracketstothe
aftermarketradiousingthescrews
suppliedwiththeradio,thensecurethe
assemblytothepocketusingthe(4)
#8x3/8”Phillipsscrews.(FigureB)
6. Mounttheassemblyintothesub-dash.
7. Reassembledashinreverseorderof
disassemblyusingtheMetratrimpanel
insteadofthefactorytrimpanel. (Figure B)
(Figure A)
Step 2
Step 1
Step 1
Step 2

Kit Assembly 99-3309B
Double DIN radio provision
1. Attachthefactoryventsandhazard
buttontotheMetratrimpanel.
(FigureA)
2. Attachtheupperdisplayshroudthe
Metratrimpanelwiththefactory
screws.(FigureA)
3. Attachtheprovided(10)panelclipsto
thelegsoftheMetratrimpanel.
4. Locatethefactorywiringharnessin
thedash.Metrarecommendsusing
thepropermatingadapterfromMetra
orAXXESS.Re-connectthenegative
batteryterminalandtesttheunitfor
properoperation.
5. Attachtheradiobracketstothe
aftermarketradiousingthescrews
suppliedwiththeradio,thenmountthe
assemblyintothesubdash.(FigureB)
6. Reassembledashinreverseorderof
disassemblyusingtheMetratrimpanel
insteadofthefactorytrimpanel. (Figure B)
(Figure A)
Step 2
Step 1
Step 1
Step 2

99-3309B
Axxess Interface
Installation From the 16-pin harness:
• ConnecttheRedwirestotheignition/accessory
wireoftheaftermarketradio.
• ConnecttheOrange/Whitewiretothe
illuminationwireoftheaftermarketradio.Ifthe
aftermarketradiohasnoilluminationwire,tapeoff
theOrange/Whitewire.
• ConnecttheBlue/Whitewiretotheampturnon
wireoftheaftermarketradio.
• ConnecttheBrownwiretothemutewireofthe
aftermarketradio.Iftheaftermarketradiodoesnot
haveaMutewire,tapeuptheBrownwire.
• ConnecttheWhitewiretotheleftfrontpositive
speakeroutputoftheaftermarketradio.
• ConnecttheWhite/Blackwiretotheleftfront
negativespeakeroutputoftheaftermarketradio.
• ConnecttheGraywiretotherightfrontpositive
speakeroutputoftheaftermarketradio.
• ConnecttheGray/Blackwiretotherightfront
negativespeakeroutputoftheaftermarketradio.
• TheVioletwireisnotusedintheapplication.
• TheViolet/Blackwireisnotusedintheapplication.
• TheGreenwireisnotusedintheapplication.
• TheGreen/Blackwireisnotusedin
thisapplication.
Thefollowingwiresarefortheaftermarketradiosthat
havenavigationbuiltin:
• ConnecttheLight Greenwiretotheparkingbrake
wireoftheaftermarketnavigationradio.
• ConnecttheBlue/PinkwiretotheVSSorspeed
sensewireoftheaftermarketnavigationradio.
• ConnecttheGreen/Purplewiretothereversewire
oftheaftermarketnavigationradio.
From the 44-way harness:
• ConnecttheBlackwiretothegroundwireofthe
aftermarketradio.
• ConnecttheRCA’stotheAUXinontheaftermarket
radio(ifequipped).
Note: This will allow you to retain the 3.5 AUX JACK
in the console.
• ConnecttheYellowwiretothe12-voltconstant
wireoftheaftermarketradio.
• Ifthevehicleisamplifieddisconnectthe4-pin
harnesslocatedbetweenthe44-wayand22-way
connectorandconnectthesupplied4-pinto4-pin
resistorpad.
•Cuttingtool•Crimpingtool•Tape•Connectors
(butt-connectors,bellcaps,etc.)
TOOLS REQUIRED
•4-pinto4-pinresistorpadharness•16-pinwith
strippedleads•22-pinto44-pinCamaroHarness
•18-pinto10-pinHVACHarness
INTERFACE COMPONENTS
FEATURES
• Providesaccessory(12-volt10-amp)
• RetainsR.A.P.(RetainedAccessoryPower)
• Usedinamplifiedornon-amplifiedsystems
• Retainsallwarningchimes
• ProvidesNAVoutputs(parkingbrake,reverse,
mute,andV.S.S.)
• RetainsOnStar/OEBluetooth
• AdjustablevolumeforchimesandOnStar
• Highlevelspeakerinput
• Micro“B”USBupdatable
• Retainsbalanceandfade
Installing the interface

99-3309B
Installing the interface
Amplified vehicles:
• ConnecttheVioletwiretotherightrearpositive
wireoftheaftermarketradio.
• ConnecttheViolet/Blackwiretotherightrear
negativewireoftheaftermarketradio.
• ConnecttheGreenwiretotheleftrearpositivewire
oftheaftermarketradio.
• ConnecttheGreen/Blackwiretotheleftrear
negativewireoftheaftermarketradio.
Non-amplified vehicles:
• CuttheresistorsfromtheGreen, Green/black,
Purple, Purple/Blackrightbelowtheheatshrink.
• ConnecttheVioletwiretotherightrearpositive
wireoftheaftermarketradio.
• ConnecttheViolet/Blackwiretotherightrear
negativewireoftheaftermarketradio.
• ConnecttheGreenwiretotheleftrearpositivewire
oftheaftermarketradio.
• ConnecttheGreen/Blackwiretotheleftrear
negativewireoftheaftermarketradio.
• ThePinkwireisnotusedinthisapplication.
Installing the interface:
1. Withalltheconnectionscompleted,plugthe16and
22pinharnessesintotheinterface.
2. Plugthe44pinGMharnessintothevehicleside
harness,andplugtheaftermarketradioharnessinto
theaftermarketradio.
3. Reconnectthenegativebatteryterminal.
Initializing the interface
Attention: If the interface loses power for any
reason, the following steps will need to be
performed again.
• Initializetheinterfacebyturningtheignitiononfor
30seconds,thenturntheignitionbackoff,then
backonagain.
Note: If using the ASWC-1, connect it after
you initialize the interface, with the key in the
off position.
Chime volume adjustment
1) Withcaron,shutoffcarandleavekeysin
ignition.Openthecardoorandleaveitopen.
Chimeswillbeheard.
2) Wait10seconds,thenwithasmall
screwdriveradjustthepotentiometerfully
counterclockwise(allthewayleft),thenclockwise
toraisechimelevelandcounterclockwisetolower
thechimelevel.
3) Whenthevolumeisatthedesiredlevel,remove
thekeysfromtheignition.Thiswilllockthechime
volumeatitscurrentlevel.
Audio level adjustment
1) Startyourvehicleandturnontheradiohaving
audioplaying.
2) Turnyouraftermarketradio’svolumeup¾oftheway.
3) Withasmallscrewdriveradjustthepotentiometer
clockwisetoraisetheaudioleveland
counterclockwisetolowertheaudiolevel.
4) Onceatdesiredlevelyouraudioadjustment
iscomplete.

99-3309B
The OEM radio is used to customize certain features of the vehicle.
UsetheoptionalLCDtoadjustthesefeaturesaccordingly:
1. PressESC,andthenpressENT:“SetLanguage”willappearonthescreen.
2. Tochangethelanguage,pressENT,andthenpressthearrowupanddown
buttonstochangethelanguage.
3. Onceyouhaveselectedyourlanguage,press ESC togobacktothe
mainscreen.
4. Ifyoudonotwishtochangethelanguage,youcanscrollupanddownthrough
thedifferentsettingswiththearrowupanddownbuttons.
Note: What these options are depends on the vehicle/trim-level it is
installed into.
5. Remembertopress ENTtochangethedesiredsetting.
Vehicle customization
with optional LCD
(AXXESSpart#XIA-LCDsoldseparately)
OnStar level adjustment
ToadjusttheOnStarvolumelevelfindtheBlack/Yellowwireonthe16-pin
harness.PushtheblueOnStarbutton,whilethevoiceisspeakingtapthe 
Black/Yellowwiretoground.Oncethevolumeissetitwillstayatthatvolume
untiltheBlack/Yellowwireistappedtogroundagain.Thiscanbesetduring
installationandthenleftalone.Ifuseradjustmentisdesired,thecustomermay
alsotap“VolumeUp”ordownonthesteeringwheel(ifequipped)toadjustthe
OnStarlevel.
Additional 12-pin harness (ASWC-1)
• This12-pinharnessistobeusedinconjunctionwiththeASWC-1
(notincluded).PleaserefertotheASWC-1instructionsforprogramming.