Metra Electronics 99-6506 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-6506
1-800-221-0932 www.metraonline.com
©COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION
KIT FEATURES
•DIN Head unit provision with pocket
•ISO DIN Head unit provision with pocket
A) Radio Housing • B) ISO Brackets • C) Trim Plate
KIT COMPONENTS
TOOLS REQUIRED:
99-6506
A
APPLICATIONS
Chrysler Pacifica
2004-2008
C
B
Phillips Screwdriver • Small Flat Blade Screwdriver • Cutting Tool • T-15 Torx Driver
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wireharnesses:
•CHTO-02 Chrysler/Dodge amplified interface 2002-up
• 70-6506 Chrysler/Dodge amplified bypass harness 2002-up
Antenna adapter:
•40-CR10 - Chrysler/Dodge antenna adapter 2002-up

Dash Disassembly
Chrysler Pacifica 2004-2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Assembly
Din Head Unit Provision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ISO Din Head Unit Provision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Final Assembly .................................... . . . 4
TABLE OF CONTENTS
99-6506
K NOWLEDGE IS P OWER
Enhanceyour installation and fabrication skillsby
enrolling in the most recognizedandrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.comor call
800-354-6782 for more informationandtake steps
toward abetter tomorrow.

99-6506
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Loosen (1) T-15 Torx screw from the
front side of shift knob and pull up to
remove. (Figure A)
NOTE: For models equipped with no
release lever on shift knob just turn
counter-clockwise to remove.
2
CHRYSLER PACIFICA 2004-2008
Unsnap floor console trim around the
shifter. Unplug harness to console
trim and remove trim.
(Figure B)
3
Unsnap and remove ignition key
trimring.
4
Unsnap and remove the dash trim
panels from eachside of the Radio/
Climate Controls.
(Figure C)
5
Remove (4) Phillips screws to
remove radio.
Note: When DIN mounting a radio a
piece of plastic in the dash cavity
may have to be removed for radio
depth clearance (
Figure D ).
6
DASH DISASSEMBLY
P
R
N
D
AUTOSTICK
A
P
R
N
D
AUTOSTICK
B
C
POWER
OUTLET
POWER
OUTLET
D

2
99-6506
KIT ASSEMBLY
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward.
(Figure A)
1
A
Slide the aftermarket head unit into
the cage and secure. Snap the
Trimplate into the Radio Housing.
(
Figure B)
2
B
POWER
OUTLET
POWER
OUTLET
C
DIN HEAD UNIT PROVISION
Note: When DIN mounting a radio a
piece of plastic in the dash cavity may
have to be removed for radio depth
clearance. (
Figure C)

3
99-6506
KIT ASSEMBLY
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit.
(Figure A)
1
A
B
Slide the head unit into the radio
opening until the side clips engage.
Snap the Trim Plate into the Radio
Housing.
(Figure B)
2
ISO DIN HEAD UNIT PROVISION

4
FINAL ASSEMBLY
1
Locate the factory wiring harness in the dash and make the connection as shown.
Metra recomends using the proper mating adapter and making the connections as
shown. (Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
2
Re-connect the negative battery terminal and test the unit for proper operation.
3
Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS
99-6506
FINAL ASSEMBLY

5
95-6506
NOTES

99-6506 INSTRUCTIONS
1-800-221-0932 www.metraonline.com
©COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION
INST99-6506
REV. 04/20/09