Metra Electronics 99-7878B User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7878B
99-7878B
APPLICATIONS
HONDA Insight
2010
KIT FEATURES
•DIN Radio Provision with Pocket
•ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
•Stacked ISO Mount Units Provision
• Painted A Matte Black Finish
•A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
•E) Double DIN Trim Plate • F) Pocket
KIT COMPONENTS
A
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver • Socket Wrench
1-800-221-0932
©COPYRIGHT 2009 METRA ELECTRONICS CORPORATION
www.metraonline.com
B
EF
CD
TOOLS REQUIRED:

Dash Disassembly
- HondaInsight2010 ................................. 1,2
Kit Assembly
-Kit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
-DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . .4
-ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 5
-Double DIN /Stacked ISO Mount Units Radio Provision . . . . . . . . . . . . .6
TABLE OF CONTENTS
99-7878B
Note:
Refer also to the instructions included with the aftermarket radio.
K NOWLEDGE IS P OWER
Enhanceyour installation and fabrication skills
by enrolling inthe most recognized andrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.com
or call 800-354-6782 formore information
and take stepstoward abetter tomorrow.

1
4
HONDAINSIGHT 2010
95-7878B DASH DISASSEMBLY
Disconnect the negative battery
terminal to prevent an accidental short
circuit.
1
Unclip and remove the pocket/acces-
sory socket panel below the factory
radio. (Figure A)
Open the glove box then use a small
blunt tool (ie: the wooden handle of a
hammer) to put pressure on the back
of the radio chassis to unclip and
remove the radio.
(Figure C)
Continued on page 2.
2
Remove (1) 8 MM bolt facing up
behind panel. Figure B)
3
OFF
REAR
FRONT
AUTO
PUSH
POWER
OUTLET
OFF
REAR
FRONT
AUTO
PUSH
B
C
A

2
7
HONDAINSIGHT 2010
95-7878B DASH DISASSEMBLY
Remove (2) Phillips screws securing the hazard switch to the back of the factory
radio panel. (Figure D)
Remove the (8) retaining clips from the factory radio panel.
(Figure D)
Continue to kit preparartion.
5
Remove (2) Phillips screws securing the air bag light to the back of the factory radio
panel. (Figure D)
6
HAZARD
SWITCH
TWO
SCREWS
AIR BAG
SWITCH
TWO
SCREWS
8 RETAINING CLIPS
D

3
99-7878B KIT PREPARATION
KIT PREPARATION
1
Secure the hazard switch into the radio housing panel using the factory hardware.
( Figure A)
2
Secure the air bag light into the radio housing panel using the factory hardware.
( Figure A)
3
Attach the (8) retaining clips to the radio housing panel in the same location as
removed from the factory radio panel. ( Figure A)
Continue to kit assembly.
HAZARD
SWITCH
TWO
SCREWS
AIR BAG
SWITCH
TWO
SCREWS
8 RETAINING CLIPS
A

99-7878B KIT ASSEMBLY
4
A
B
C
DIN MOUNT RADIO PROVISION WITH POCKET
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
1
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure A)
2
Snap the pocket into the bottom
opening of the radio housing.
(Figure B)
3
Slide the aftermarket head unit into
the cage and secure.
(Figure C)
4
Reassemble dash in reverse order of
disassembly.
5
* Note: Refer also to the instructions included with the aftermarket radio.

99-7878B KIT ASSEMBLY
5
A
B
C
ISO MOUNT RADIO PROVISION WITH POCKET
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
1
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. (Figure A)
2
Snap the pocket into the bottom
opening of the radio housing.
(Figure B)
3
Slide the head unit into the radio
opening until the side clips engage.
(Figure C)
4
Snap the Trim plate into the Radio
Housing.
(Figure C)
5
Reassemble dash in reverse order of
disassembly.
6
* Note: Refer also to the instructions included with the aftermarket radio.

99-7878B KIT ASSEMBLY
DOUBLE DIN/STACKED ISO MOUNT
UNITS RADIO PROVISION
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
1
Cut and remove the center bar from
the radio housing. (Figure A)
2
Snap the Double DIN brackets to the
inside edge of the Double DIN trim
plate.
(Figure B)
3
Slide the Double DIN head unit or
stacked ISO head units into the
bracket/radio housing assembly and
secure the Double DIN head unit or
stacked ISO head units to the
assembly using the screws supplied
with the radio.
(Figure C)
4
* Note: Refer also to the instructions included with the aftermarket radio.
A
B
C
Reassemble dash in reverse order of
disassembly.
6
Snap the Double DIN trim plate into the
Radio Housing. (Figure C)
5
1-800-221-0932
REV. 07/15/09 © COPYRIGHT 2009 METRA ELECTRONICS CORPORATION INST99-7878B
www.metraonline.com