Metra Electronics 99-7334 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7334
99-7334
APPLICATIONS
KIA Borrego 2009
KIT FEATURES
•DIN Radio Provision
•ISO DIN Radio Provision
•Double DIN Radio Provision
•Stacked ISO Mount Units Provision
A) Radio Housing •B) ISO Trim Plate •C) ISO Brackets •D) Double DIN Trim Plate
•E) Double DIN Brackets •F) Pocket
Wiring & Antenna Connections (sold separately)
•70-7303 - Hyundai / Kia Harness 2009
•40-KI10 - Kia Antenna Adapter 2007-up
KIT COMPONENTS
A
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
www.metraonline.com
B
DEF
C
TOOLS REQUIRED:

Dash Disassembly
- KIA Borrego 2009 . . . . . . . . . . . . . . . . . . .... . . . . . . . . . . . . . 1
Kit Assembly
- DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
- ISO Mount Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
- Double DIN/Stacked ISO Mount Units Provision. . . . . . . . . . . . . . . . . . 4
Final Assembly .......................................... . 5
TABLE OF CONTENTS
99-7334
*Note:
Refer also to the instructions included with the aftermarket radio.
K
NOWLEDGE IS
P
OWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.

99-7334 DASH DISASSEMBLY
KIA BORREGO 2009
A
B
C
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unclip and remove the side trim
panels. ( Figure A)
2
Remove (4) Phillips screws securing
the radio and (2) Phillips screws
securing the A/C vent panel above the
radio.
(Figure B)
3
Unclip and remove the radio and A/C
vent panel as one piece then unplug
the radio and vent panel and separate.
(Figure C)
4
Continue to kit assembly.

99-7334 KIT ASSEMBLY
DIN RADIO PROVISION
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward. (Figure A)
1
Slide the aftermarket radio into the
cage until it snaps into place. (Figure B)
2
Snap the pocket into the bottom
opening of the radio housing.
(Figure C)
3
2
A
B
C
*Note: Refer also to the instructions included with the aftermarket radio.
Continue to final assembly.

99-7334 KIT ASSEMBLY
3
A
B
C
D
ISO MOUNT RADIO PROVISION
Mount the ISO Brackets to the radio
using the screws supplied with the
radio. (Figure A)
1
Slide the radio/bracket assembly into
the radio housing until it snaps into
place. (Figure B)
2
Snap the ISO Trim plate onto the front
of the Radio Housing.
(Figure C)
3
Snap the pocket into the bottom
opening of the radio housing.
(Figure D)
4
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-7334 KIT ASSEMBLY
4
A
B
C
DOUBLE DIN/STACKED ISO MOUNT UNITS PROVISION
Cut and remove the center bar from
the radio housing. (Figure A)
1
Snap the Double DIN brackets to the
inside edge of the Radio Housing.
(Figure B)
2
Snap the Double DIN Trim plate onto
the front of the Radio Housing.
(Figure C)
4
Slide the Double DIN or stacked ISO
mount unit(s) into the bracket/radio
housing assembly and secure the
unit(s) to the assembly using the
screws supplied with the unit(s).
(Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.

99-7334 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc..........Red
12V Batt / Memory. . . . . . . . . Yellow
Ground..................Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer.................Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
Enjoy your newly installed radio!
5

99-7334 INSTRUCTIONS
1-800-221-0932
REV. 09/01/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-7334
www.metraonline.com