Metra Electronics 99-7524B User manual

Installation instructions for 99-7524B
METRA. The World’s best kits.™metraonline.com © COPYRIGHT 2015 METRA ELECTRONICS CORPORATION
REV. 9/23/2015 INST99-7524B
Table of Contents
CAUTION! Metra recommends disconnecting the negative bat -
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con-
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
20;*64765,5;:
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Painted charcoal black
20;-,(;<9,:
>0905.(5;,55(*655,*;065: (sold separately)
Wiring Harness: • Included with kit
Antenna Adapter: • Not required
• Panel removal tool • Phillips screwdriver
• 10mm Socket wrench
;663:9,8<09,+
Mazda 6 2006-2008
99-7524B
Dash Disassembly .............................................. 2-4
Kit Preparation
–Electronic climate control..................................... 5
–Manual climate control......................................... 6
–Felt tape application............................................. 7
Kit Assembly
–ISO DIN radio provision with pocket...................... 8
–ISO DDIN radio provision ...................................... 8
Wiring Installation ..................................................9
Installing the 99-7524B ........................................10
Display customization..........................................11
• A) Radio/climate control panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8” Phillips screws
• E) (6) Panel clips • F) (2) #8 x 1” Phillips screws • G) Harness • H) Manual climate harness
AB
E
CD
GH
F

99-7524B
Electronic climate control
1. Unscrew the shift knob counter
clockwise to remove. (Figure A)
2. Unclip and remove the cup holder/
parking brake cover and shifter
cover as one radio. (Figure B)
3. Remove (2) Phillips screws from
the bottom of the radio/climate
control panel. (Figure C)
4. Open glove box, squeeze sides
together and let open fully then
remove (1) 10mm bolt from the
side of the radio bracket.
(Figure D)
Dash Disassembly
Rear of Electronic Climate Control
Rear of Radio/Climate Control Panel
INSIDE
GLOVE BOX
(Figure B)
(Figure F)
(Figure E)
(Figure C)
(Figure G)
(Figure D)(Figure A)
2
5. Unsnap and remove radio/climate
control panel including climate
control vents at the top. (Figure E)
6. Remove (4) Phillips screws
securing vents to radio/climate
control panel to remove. (Figure F)
7. Remove (8) Phillips screws
securing the electronic climate
control to the radio/climate control
panel to remove. (Figure G)
Continue to kit preparation

99-7524B
Manual climate control
1. Unscrew the shift knob counter
clockwise to remove. (Figure A)
2. Unclip and remove the cup holder/
parking brake cover and shifter
cover as one radio. (Figure B)
3. Remove (2) Phillips screws from
the bottom of the radio/climate
control panel. (Figure C)
4. Pull the climate control knobs off
and remove (2) Phillips screws
from behind knobs. (Figure D)
Dash Disassembly
(Figure B)
(Figure F)
(Figure A)
(Figure E)
(Figure C)
(Figure G)
(Figure D)
3
5. Open glove box, squeeze sides
together and let open fully then
remove (1) 10mm bolt from the
side of the radio bracket. (Figure E)
6. Unsnap and remove radio/climate
control panel including climate
control vents at the top. (Figure F)
7. Remove (4) Phillips screws
securing vents to radio/climate
control panel to remove. (Figure G)
Continue on the next page
INSIDE
GLOVE BOX
A/C

99-7524B
Manual climate control (continued)
8. Remove the (2) small Phillips
screws securing the light bulb
boards on each side of the
backlight dispersion bar.
Note: Notice how they are
positioned in the backlight
dispersion bar as they will be
placed in the 99-7524B the same
way. (Figure H)
9. Remove (4) Phillips screws
securing backlight dispersion bar
and knob trim bezels. (Figure I)
10. Push the bottom edges of the knob
trim bezels from the front side to
the back and slide both pieces out
as one radio. (Figure J)
Continue to kit preparation
Dash Disassembly
4
(Figure H) (Figure J)
(Figure I)

99-7524B
5
Kit Preparation
Electronic climate control
1. Clip the climate control knob outer trim ring panel
into the 99-7524B housing. (Figure A)
2. Align the screw holes in the climate control and the
radio housing panel then push the climate control
onto the radio housing panel. (Figure B)
3. Secure the climate control with the factory
hardware removed in step 7 of the dash
disassembly for electronic climate control cars.
4. Unclip and remove the small oval cover plate at the
bottom center of the factory radio and insert into
the 99-7524B radio housing. (Figure C)
5. Attach (6) panel clips supplied to the radio
housing.
Note: The light bulb boards will not be used with
auto climate control vehicles disregard these bulbs.
(Figure B)
REAR VIEW OF ELECTRONIC CLIMATE CONTROL
(Figure A) (Figure C)

99-7524B
Kit Preparation
Manual climate control
1. Put the climate control knob
outer trim panel and the backlight
dispersion bar together and clip
into the radio housing panel as
one radio.
Note: You may have to push down
slightly on the middle of the radio
to ease in positioning it into the kit.
(Figures A, B, C)
2. Secure the radio with the factory
hardware previously removed from
the manual climate control
dash disassembly.
3. Secure the light bulb boards
on each side of the backlight
dispersion bar using the factory
hardware removed in step 8 in
manual climate control dash
disassembly. (Figure D)
4. Unclip and remove the small oval
cover plate at the bottom center of
the factory radio and insert into the
99-7524B radio housing.
(Figure E)
5. Attach (6) panel clips supplied to
the radio housing.
(Figure D)(Figure B)
(Figure E)(Figure C)(Figure A)
ASSEMBLED
INSTALLED
6

99-7524B
Kit Preparation
7
Felt tape application
Note: Due to differences in factory
tolerances you may need to apply the
provided felt tape to the edge of the
99-7524B radio housing to relieve
backlight bleed through.
1. Looking at edge of radio housing
apply felt tape to inner edge (toward
back of kit). If it is positioned to
closely to the outer edge you may be
able to see it once it is in the dash.
(Figure A)
(Figure A)
Apply to back of both sides

99-7524B
Kit Assembly
8
ISO DIN radio provision with pocket
1. Mount the pocket to the radio
brackets with (4) #8 x 3/8” Phillips
screws supplied. (Figure A)
2. Remove the metal DIN sleeve and
trim ring from the aftermarket
radio.
3. Slide the radio into the bracket/
pocket assembly, and then secure
with the screws supplied with the
radio. (Figure B)
Continue to the Wiring Installation
ISO DDIN radio provision
1. Attach the radio brackets to the
radio using the screws supplied
with the radio. (Figure A)
Continue to the Wiring Installation
(Figure A)
(Figure B)
(Figure A)

99-7524B
9
Wiring Installation
Connections to be made to the aftermarket radio:
• Connect the Black wire to the ground wire.
• Connect the Yellow wire to the battery wire.
• Connect the Red wire to the accessory wire.
• Connect the Orange wire to the illumination wire. If the aftermarket
radio has no illumination wire, cap off the Orange wire.
•
Cap off and disregard the Orange/White wire, it will not be used in this
application.
• Connect the Blue wire to the antenna turn on wire.
•
Connect the Blue/White wire to the amp turn-on wire, if the vehicle is amplified .
• Connect the White wire to the left front positive speaker output.
• Connect the White/Black wire to the left front negative speaker output.
• Connect the Gray wire to the right front positive speaker output.
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the Green wire to the left rear positive speaker output.
• Connect the Green/Black wire to the left rear negative speaker output.
• Connect the Purple wire to the right rear positive speaker output.
•
Connect the Purple/Black wire to the right rear negative speaker output.
• 12-pin pre-wired ASWC-1 harness:
This harness is to be used along with the optional ASWC-1 (not included)
to retain steering wheel audio controls. If the ASWC-1 is not being used,
disregard this harness. If it will be used, please refer to the ASWC-1
instructions for radio connections and programming.
Note: Disregard the harness that comes with the ASWC-1.

99-7524B
Connection Legend
(99-7524 radio housing diagram)
*Note: Location 2 will not be used in this application.
Location 1Location 3
*Location 2
10
Installing the 99-7524B
1. Connect the 8-pin connector supplied, into Location 1, on the back of the radio/
climate-control housing. (see Connection Legend)
Note: If this connector is not plugged in, the kit will not operate.
2. For manual climate control vehicles only, connect the 16-pin connector
supplied, into Location 3, on the back of the radio/climate-control housing.
(see Connection Legend)
3. Locate the factory wiring harness and antenna connector in the dash, and
complete all necessary connections to the radio.
4. Mount the completed assembly into the dash, and then reassemble the dash in
reverse order of disassembly, using the 99-7524B radio/climate panel.
Note: There are no existing holes for mounting the radio. New holes will need
to be made using (2) #8 x 1” Phillips screws supplied . The radio brackets will
rest on a shelf in the sub-dash. Be sure the radio is level and centered while
mounting the completed assembly into the dash opening.
5. Start the car and test all the climate control functions.
Note: The air recirculation light will be on at initial startup and will not go out
until using the climate controls for the first time.