Metra Electronics 99-7335S User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7335S
99-7335S
APPLICATIONS
HYUNDAI Veracruz
2007-2010
Automatic climate control only
KIT FEATURES
•DIN Radio Provision with Pocket
•ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
•Stacked ISO Mount Units Provision
•Painted to match factory dash-”S”=Silver
•A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
•E) Double DIN Trim Plate • F) Pocket
KIT COMPONENTS
A
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver
1-800-221-0932
©COPYRIGHT 2009 METRA ELECTRONICS CORPORATION
www.metraonline.com
BE
F
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-1004 -KIA/Hyundai harness 2004-up
•70-7303 -KIA/Hyundai harness 2009
Antenna Adapter:
•40-KI11 - KIA antenna adapter 2007-up
CD
TOOLS REQUIRED:

Dash Disassembly
- Hyundai Veracruz 2007-2010
(Automatic climate controlonly).......................
..1
Kit Assembly
-Kit Preparation ........................ . . . . . . . . . . . . . . . . . . 2
-DIN Mount Radio Provision with Pocket ........................3
-ISO Mount Radio Provision with Pocket........................ 4
TABLE OF CONTENTS
99-7335S
Note:
Refer also to the instructions included with the aftermarket radio.
K NOWLEDGE IS P OWER
Enhanceyour installation and fabrication skills
by enrolling inthe most recognized andrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.com
or call 800-354-6782 formore information
and take stepstoward abetter tomorrow.

1
4
HYUNDAI VERACRUZ 2007-2010
95-7335S DASH DISASSEMBLY
Disconnect the negative battery
terminal to prevent an accidental short
circuit.
1
Unclip and remove the side trim
panels. (Tip: start at the bottom of the
panels) (Figure A)
Remove (4) Phillips screws securing
the climate control, (2) Phillips screws
securing the clock display and (4)
Phillips screws securing the pocket
from the radio trim panel.
(Figure C)
Continue to kit preparartion.
2
Remove (6) Phillips head screws
securing the radio trim panel and
remove trim panel. (Figure B)
3
CLOCK DISPLAY-REAR VIEW
CLIMATE CONTROL-REAR VIEW
RADIO HOUSING
REAR VIEW
POCKET-REAR VIEW
C
B
A

2
99-7335S KIT ASSEMBLY
KIT PREPARATION
1
Attach the climate control, pocket and the clock display into the 99-7335S radio
housing using the factory hardware. ( Figure A)
Continue to kit assembly.
H
M
R
PUSH
A/C
TEMP
PASSENGER
DUAL
REAR
REAR
FRONT
MODE
OFF
AUTO
A
MANUAL
TEMP
A

99-7335S KIT ASSEMBLY
3
A
B
C
DIN MOUNT RADIO PROVISION WITH POCKET
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
1
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure A)
2
Snap the pocket into the bottom
opening of the radio housing.
(Figure B)
3
Slide the aftermarket head unit into
the cage and secure.
(Figure C)
4
Reassemble dash in reverse order of
disassembly.
5
* Note: Refer also to the instructions included with the aftermarket radio.