Metra Electronics 99-7617HG User manual

METRA - The World’s best kits ®metraonline.com
REV. 11/14/2017 INST99-7617GHG
Installation instructions for part 99-7617HG
®
CAUTION! All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
U.S. PATENT # D757,707
• ISO DIN radio provision with pocket
• Painted high gloss gray
• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8” Phillips screws
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-7552
Antenna Adapter: • 40-NI12
Steering wheel control interface: • ASWC-1 (sold separately)
• Panel removal tool • Phillips screwdriver
TOOLS REQUIRED
Nissan Altima (Sedan) 2013-2015
99-7617GHG
ABCD
Dash Disassembly ................................................. 2
Kit Assembly
–ISO DIN radio provision with pocket ....................... 3
Table of Contents

99-7617HG
®
1. Unclip the right side of the driver’s
knee bolster panel next to the
center console and let hang.
(Figure A)
Note: There is no need to
completely remove the panel.
2. Unclip and remove the (2) silver
side trim panels from each side of
the factory radio. (Figure B)
3. Unclip and remove the trim panel
below the climate control panel.
4. Remove the (4) Phillips screws
securing the climate control panel
and a/c vent panel. (Figure C)
Dash Disassembly
(Figure D)(Figure A)
(Figure E)(Figure B)
(Figure F)(Figure C)
5. Remove the climate control panel.
(Figure D)
6. Remove the a/c vent panel.
(Figure E)
7. Remove the (4) Phillips screws
securing the radio, and then
remove. (Figure F)
8. If equipped with automatic
climate controls, remove the
(2) Phillips screws securing the
climate module under the radio.
This module will be reused in Kit
Assembly.
Continue to Kit Assembly
2

99-7617HG
®
Kit Assembly
(Figure A) (Figure B) (Figure C)
ISO DIN radio provision with pocket
1. Attach the pocket to the radio
brackets using the (4) #8 x 3/8”
Phillips screws provided. (Figure A)
2.
If equipped with automatic climate
controls, secure the climate module
removed in Dash Disassembly,
to the radio brackets, using the
factory hardware. (Figure B)
3. Remove the metal DIN sleeve and
trim ring from the aftermarket radio
.
4. Slide the radio into the bracket/
pocket assembly, and then secure
it using the screws supplied with
the radio. (Figure C)
5. Locate the factory wiring harness
and antenna connector in the dash.
Metra recommends using the
proper mating adapters from Metra
and/or AXXESS.
6. Reassemble the dash in reverse
order of disassembly.
3

METRA - The World’s best kits ®metraonline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
REV. 11/14/2017 INST99-7617GHG
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
Installation instructions for part 99-7617HG
®
IMPORTANT
If you are having difficulties with the
installation of this product, please call our
Tech Support line at 1-800-253-TECH.
Before doing so, look over the instructions a
second time, and make sure the installation
was performed exactly as the instructions
are stated. Please have the vehicle apart
and ready to perform troubleshooting steps
before calling.

METRA - The World’s best kits ®metraonline.com
REV. 11/14/2017 INST99-7617GHG
Instrucciones de instalación para la pieza 99-7617HG
®
¡PRECAUCIÓN! Todos los accesorios, interruptores, paneles de con-
troles de clima y especialmente las luces del indicador de las bolsas
de aire deben estar conectados antes ciclar la ignición. Además, no
quite el radio de fábrica con la llave en la posición o de encendido ni
con el vehículo funcionando.
© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
U.S. PATENT # D757,707
• Provisión de radio ISO DIN con cavidad
• Pintado de alto brillo gris
• A) Panel de moldura de radio • B) Soportes del radio • C) Cavidad • D) (4) Tornillos Phillips #8 de 3/8”
CARACTERÍSTICAS DEL KIT
COMPONENTES DEL KIT
CABLEADO Y CONEXIONES DE ANTENA (se venden por separado)
Arnés de cableado: • 70-7552
Adaptador de antena: • 40-NI12
Interfase de control en volante: • ASWC-1 (se venden por separado)
• Herramienta para quitar paneles
• Destornillador Phillips
HERRAMIENTAS REQUERIDAS
Nissan Altima (Sedan) 2013-2015
99-7617GHG
ABCD
Desmontaje del tablero ......................................... 2
Ensamble del kit
–Provisión de radio ISO DIN con cavidad.................. 3
Indice