Metra Electronics 99-7860 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7860
99-7860
APPLICATIONS
Honda Civic SI
2002-2005
(US Models Only)
KIT FEATURES
•DIN Head Unit Provision With Pocket
•ISO DIN Head Unit Provision With Pocket
•Stacked ISO Head Unit Provision
• Double DIN Head Unit Provision
•A) Single DIN Radio Housing • B) ISO Brackets • C) ISO Trim Plate
•D) Double DIN Trim Plate
KIT COMPONENTS
•Phillips Screwdriver • Offset Tool (Not Pictured)
A
TOOLS REQUIRED:
BC
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
•70-1721 - Honda/Acura harness 1998-up
Antenna Adapter
•Not Required
D

99-7860 DASH DISASSEMBLY
Honda Civic SI 2002-2005
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Remove the shift knob and unsnap
the shifter lever trim panel.
2
Using the offset tool remove (2) lower
bolts securing the center panel.
3
Unsnap and remove the dash trim
bezel and disconnect the wiring.
4
Remove (3) Philips screws securing
the climate control pod to the back of
the dash trim bezel and remove the
pod.
5
Remove (4) Phillips screws from each
side securing the factory head unit
and pocket to the bracket assembly
and remove.
6
NOTE: Removing the glove box and
the drivers side lower trim panel may
be necessary when removing the
shifter level trim panel when not
using an offset tool.
Continue to kit assembly.

99-7860 KIT ASSEMBLY
A
B
C
Slide the DIN cage into the radio
opening of the Housing and secure by
bending the metal locking tabs down.
(Figure A)
1
Snap the housing assembley into the
dash trim bezel. (Figure C)
3
Slide the DIN unit into the cage until it
is secure. (Figure B)
2
* Note: Refer also to the instructions included with the aftermarket radio.
DIN HEAD UNIT PROVISION WITH POCKET
Continue to final assembly.
Assembled kit.

99-7860 KIT ASSEMBLY
A
B
C
Align the holes in the ISO Snap-In
Backets with the holes in the head
unit and mount the brackets to the
head unit with the screws supplied
with the unit.
(Figure A)
1
Slide the head unit/bracket assembly
into the radio opening until the side
clips engage. (Figure B)
2
Snap the ISO trimplate over the head
unit. (Figure C)
3
Snap the housing assembly into the
dash trim bezel. (Figure C)
4
*
Note: Refer also to the instructions included with the aftermarket radio.
ISO DIN HEAD UNIT PROVISION WITH POCKET
NOTE: To remove the mounted head
unit, unclip and remove the ISO
Trimplate. Using a small flat blade
screwdriver, disengage the side clips
securing the ISO Snap In Brackets to
the housing/pocket assembly.
Continue to final assembly.
Assembled kit.

99-7860 KIT ASSEMBLY
A
B
C
Align the holes on the factory backet
assembly with the holes on the after-
market Double DIN head unit and
mount with the screws supplied with
the unit.
(Figure A)
1
Cut and remove the center rib (shad-
ed) from the Double DIN Trimplate.
(Figure B)
2
Snap the Double DIN Trimplate over
the head unit. (Figure C)
3
*
Note: Refer also to the instructions included with the aftermarket radio.
DOUBLE DIN HEAD UNIT PROVISION
Continue to final assembly.
Assembled kit.

99-7860 KIT ASSEMBLY
A
B
Align the holes on the factory backet
assembly with the holes on the after-
market ISO head units and mount
with the screws supplied with the
unit.
(Figure A)
1
Snap the Double DIN Trimplate over
the head unit. (Figure B)
2
*
Note: Refer also to the instructions included with the aftermarket radio.
STACKED ISO HEAD UNIT PROVISION
Continue to final assembly.
Assembled kit.

99-7860 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
METRA ACCESSORIES STEREO DASH KITS