Metra Electronics 99-7519B User manual

INSTALLATION INSTRUCTIONS FOR PART 99-7519B
Cutting Tool • Phillips Screwdriver • Socket Wrench
1-800-221-0932 www.metraonline.com
KIT FEATURES
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
• DIN Head Unit Provision with pocket
• ISO DIN Head Unit Provision with pocket
• Double DIN Head Unit Provision
• Stacked ISO DIN Head Unit Provision
• Painted Matte Black to Match Factory
A) Radio Housing • B) Snap-In Pocket • C) ISO Brackets • D) ISO Trim Plate • E) Double DIN Brackets
• F) Double DIN Trim Plate • G) (4) Panel Clips
KIT COMPONENTS
TOOLS REQUIRED:
99-7519B
APPLICATIONS
2009-2010
C
BE
D
F
F
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-7903 - Mazda harness 2001-up
Antenna Adapter:
• Not required
Mazda MX-5 Miata
A

Dash Disassembly ....................................................................... 1-3
Kit Preparation ............................................................................... 4
Kit Assembly:
DIN Head Unit Provision.................................................................. 5
ISO DIN Head Unit Provision........................................................... 6
Double DIN Head Unit Provision..................................................... 7
Stacked ISO DIN Head Unit Provision............................................ 8
Final Assembly .............................................................................. 9
99-7519B
TABLE OF CONTENTS
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills
by enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com
or call 800-354-6782 for more information
and take steps toward a better tomorrow.
Metra reccommends MECP
certified technicians
CAUTION : Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.

99-7519B DASH DISASSEMBLY
1
Unclip panel below steering column
and remove. (Figure A)
2
MAZDA MX-5 MIATA 2009-2010
Remove (4) Phillips screws from
metal brace below steering column
and remove. (Figure A)
3
Looking at the side of the radio/cli-
mate control panel from underneath
the steering column opening, remove
(1) 10mm bolt from the side of the
radio chassis. (Figure B)
With the center console lid closed
unclip and remove the cover on the
back side of the center console and
remove the (2) Phillips screws
revealed. (Figure C)
4
Remove the rubber mat inside of the
cup holder then remove the (1)
Phillips screw revealed. (Figure D)
5
A
B
C
D
1

Carefully remove the side panels
from each side of the radio/climate
control panel by pulling straight back
towards the rear of the car.
(Figure G)
8
G
99-7519B DASH DISASSEMBLY
MAZDA MX-5 MIATA 2009-2010
6
Unclip, unplug and remove the entire
center console. (Figure E)
7
Remove the (2) Phillips screws
securing the side panels from each
side of the radio/climate control
panel. (Figure F)
E
F
2

99-7519B DASH DISASSEMBLY
Remove (2) Phillips screws, (1) on
each side, from the side of the
radio/climate control panel.
(Figure H)
9
Pull radio/climate control panel out,
disconnect plugs and remove.
(Figure I)
10
MAZDA MX-5 MIATA 2009-2010
Turn the radio/climate control panel
over and remove the (4) screws that
hold the climate control to the bezel,
then remove the climate control.
(Figure J)
11
H
I
J
3

99-7519B KIT PREPARATION
Attach the (4) Panel Clips to the posts
on the back of the radio housing.
(Figure A)
1
MAZDA MX-5 MIATA 2009-2010
A
4

Turn over the 99-7519B housing,
take the climate control and screws
removed from the factory panel and
attach the climate control to the kit
housing using the factory screws.
(Figure A)
1
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down.
(Figure C)
3
A
C
D
Slide the pocket into the bottom
section of the kit housing.
(Figure B)
2
Slide the aftermarket head unit into
the cage and secure.
(Figure D)
4
DIN HEAD UNIT PROVISION
B
99-7519B
KIT ASSEMBLY
5

Mount the ISO Brackets to the head
unit with the screws supplied with
the unit.
(Figure C)
3C
D
Slide the pocket into the bottom
section of the kit housing.
(Figure B)
2
Slide the head unit into the radio
opening until the side clips engage.
(Figure D)
4
ISO DIN HEAD UNIT PROVISION
99-7519B
KIT ASSEMBLY
Turn over the 99-7519B housing,
take the climate control and screws
removed from the factory panel and
attach the climate control to the kit
housing using the factory screws.
(Figure A)
1
A
B
Snap the Trim plate into the Radio
Housing.
(Figure D )
5
6

Slide the appropriate DDIN bracket
into the kit housing.
(Figure B)
3
C
Cut the rib in the middle of the 99-
7519B housing to make room for the
DDIN brackets.
(Figure A)
2
Slide the DDIN radio unit into DDIN
brackets and secure the unit to the
kit using the screws supplied with
the head unit.
(Figure C)
4
DOUBLE DIN HEAD UNIT PROVISION
99-7519B
KIT ASSEMBLY
Turn over the 99-7519B housing,
take the climate control and screws
removed from the factory panel and
attach the climate control to the kit
housing using the factory screws.
(Figure A)
1
A
B
Snap the DDIN trim plate into the
front of the kit housing.
(Figure C )
5
7

Slide the appropriate DDIN bracket
into the kit housing.
(Figure B)
3
C
Cut the rib in the middle of the 99-
7519B housing to make room for the
DDIN brackets.
(Figure A)
2
Slide the stacked ISO DIN units into
the DDIN bracket assembly and
secure the units to the kit using the
screws supplied with the head units.
(Figure C)
4
STACKED ISO DIN HEAD UNIT PROVISION
99-7519B
KIT ASSEMBLY
Turn over the 99-7519B housing,
take the climate control and screws
removed from the factory panel and
attach the climate control to the kit
housing using the factory screws.
(Figure A)
1
A
B
Snap the DDIN trim plate into the
front of the kit housing.
(Figure C )
5
8