Metra Electronics 95-9308B User manual

METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION
APPLICATIONS
KIT FEATURES
KIT COMPONENTS
TOOLS REQUIRED
1-800-221-0932 metraonline.com
METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION
REV. 7/30/2010
1-800-221-0932 metraonline.com
INSTALLATION INSTRUCTIONS FOR PART 95-9308BINSTALLATION INSTRUCTIONS FOR PART 95-9308B
BMW X5
2000 - 2006
(non-navigation models)
95-9308B
• DDIN Head Unit Provision
• ISO Stacked Head Unit Provision
• Painted Scratch Resistant Matte Black
• DDIN Radio Trim Plate • DDIN Brackets • (4) Plastic Snaps • (8) Flush ISO Screws
• Phillips Screwdriver • Torx Screwdriver • Panel Removal Tool
• Small Flat Blade Screwdriver • Cutting Tool or File

TABLE OF CONTENTS NOTES
DASH DISASSEMBLY
• BMW X5 2000 - 2006 . . . . . . . . . . . . . . 1,2
KIT ASSEMBLY
• BMW X5 2000 - 2006 . . . . . . . . . . . . . . . 3
*NOTE: Refer Also to the instructions included with the aftermarket radio.
Metra recommends MECP certified
technicians
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
95-9308B 95-9308B

1
BMW X5 2000-2006
95-9308B DASH DISASSEMBLY
Disconnect the negative
battery terminal to prevent an
accidental short circuit.
Remove the volume knob.
(Fig. A)
Using a T-10 torx-head
screwdriver, turn the release
lever under the shaft 90º.
(Fig. A)
Leaving the screwdriver
in position, pull out on the
bottom of the factory head unit
and remove the unit. (Fig. A)
Disconnect the wiring.
Using a T-10 torx-head
screwdriver, loosen (2) T-10
torx-head screws located
beside the head unit guides
and remove the top of the
factory head unit. (Fig. B)
Disconnect the wiring. Continued on Pg. 2 .............
1
2
3
A
B
4
5
6
7
NOTES
95-9308B

2 3
BMW X5 2000-2006 BMW X5 2000-2006
8
9
.............Coninued from Pg. 1
With the factory radio door
open, press in on the tabs at
either side and remove the
door. (Fig. C)
Cut and remove shown sec-
tion from the sub dash.
(Fig. D)
Mount the DDIN radio to the
supplied DDIN brackets us-
ing the ISO screws supplied
with the aftermarket radio
(screws must be fl ush).
(Fig. A)
Locate the factory wiring har-
ness in the dash. Metra rec-
ommends using the proper
mating adapters from Metra
and AXXESS to integrate
your new radio. Re-connect
the negative battery terminal
and test the unit for proper
operation.
Snap the radio bracket as-
sembly into the dash opening
(tight fi t). (Fig. B)
Snap the DDIN trim plate
over the radio (be sure to
align the snaps with the
holes in the brackets or it
won’t seat properly). (Fig. B)
95-9308B DASH DISASSEMBLY 95-9308B KIT ASSEMBLY
1
2
3
4
C A
D B
Continue to Kit Assembly