MicroBoards Technology CX-1 Publisher User manual

CX-1 Disc Publisher
For Microsoft Windows®7, Vista, and XP
Users Manual
Microboards Technology LLC Version 4.00

2

MICROBOARDS TECHNOLOGY, LLC CX-1 DISC PUBLISHER
3
TABLE OF CONTENTS
INTRODUCTION..............................................................................................................................................................5
WHAT’S INCLUDED ...........................................................................................................................................................5
SYSTEM REQUIREMENTS ...................................................................................................................................................6
ASSEMBLY AND INSTALLATION...............................................................................................................................6
ASSEMBLY INSTRUCTIONS ................................................................................................................................................6
FRONT PANEL INDICATORS AND BUTTONS........................................................................................................................7
LOADING DISCS.................................................................................................................................................................7
INSTALLING INK CARTRIDGES...........................................................................................................................................8
Supported Ink Cartridges .............................................................................................................................................8
Loading / Replacing Ink Cartridges .............................................................................................................................8
Replacing Empty Ink Cartridges...................................................................................................................................9
CX-1 DISC PUBLISHER INSTALLATION............................................................................................................................10
WINDOWS COMPONENT PREREQUISITES .........................................................................................................................10
CONNECTING TO A PC.....................................................................................................................................................10
WINDOWS VISTA HARDWARE INSTALLATION.................................................................................................................11
WINDOWS XP HARDWARE INSTALLATION......................................................................................................................11
PRINTING PREFERENCES..........................................................................................................................................13
COLOR TAB.....................................................................................................................................................................13
More Color Options....................................................................................................................................................13
ADVANCED TAB..............................................................................................................................................................14
DIAMETER SETTINGS TAB ...............................................................................................................................................14
INK TAB ..........................................................................................................................................................................15
ALIGNMENT TAB.............................................................................................................................................................15
PRINT QUALITY TAB .......................................................................................................................................................16
Printing Recommendations.........................................................................................................................................16
ABOUT TAB.....................................................................................................................................................................16
THE MICROBOARDS PRINTER TOOLBOX............................................................................................................17
CLEANING .......................................................................................................................................................................17
PEN CALIBRATION...........................................................................................................................................................17
AUTOMATIC MARGIN CALIBRATION ...............................................................................................................................18
PRINT TEST DISC.............................................................................................................................................................18
EXERCISE BELT...............................................................................................................................................................18
USING SURETHING DISC LABELER........................................................................................................................18
THE CX-1 DISC PUBLISHER SOFTWARE ...............................................................................................................19
MICROBOARDS PRINTWRITE...........................................................................................................................................19
PRASSI ZULU2.................................................................................................................................................................19
ZULU2AND PRINT ONLY MODE......................................................................................................................................21
ZULU2ROBOTICS UTILITIES............................................................................................................................................21
Enable Configure Dialog............................................................................................................................................21
Exercise Belts .............................................................................................................................................................21
Unload the Drive ........................................................................................................................................................21
SOFTWARE RE-INSTALLATION...............................................................................................................................22
TOOLBOX RE-INSTALLATION ..........................................................................................................................................22
DISC PUBLISHING SOFTWARE RE-INSTALLATION............................................................................................................22
SURETHING LABELER SOFTWARE RE-INSTALLATION .....................................................................................................23
TROUBLESHOOTING...................................................................................................................................................24
PRINTER NOT PRINTING ...................................................................................................................................................24
DISK LOAD ERROR...........................................................................................................................................................24
OUT OF MEDIA INDICATOR ON FRONT PRINTER PANEL...................................................................................................24
GAPS OR OVERLAP IN INK COVERAGE.............................................................................................................................24
PRINTING OFF THE PRINTABLE SURFACE.........................................................................................................................24
“NO PRINTERS CONNECTED”MESSAGE ..........................................................................................................................25
LOW INK WARNING.........................................................................................................................................................25
OUT OF INK MESSAGE.....................................................................................................................................................25
PRINTING SPECIFICATIONS .....................................................................................................................................26
TECHNICAL SUPPORT ................................................................................................................................................27

4
Any unauthorized modification to this equipment may result in the revocation by the FCC of the user’s authority to
operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and antenna
•Connect the equipment into an outlet on a circuit different than that to which the receiver is connected
•Consult the dealer or an experienced radio/TV technician for help
This product is in conformity with the EMC Directive (89/336/EEC) through compliance with the following European standards: EN 55022,
EN 55024. The CE mark has been affixed in accordance with the CE Marking Directive 93/68/EEC.
Canadian Department of Communications (DOC) Statement
This Class B digital apparatus complies with the Canadian ICES-003 Issue 4:2004. Cet appareil numerique de la classe B est conforme a la
norme NMB-003 du Canade.

MICROBOARDS TECHNOLOGY, LLC CX-1 DISC PUBLISHER
5
Introduction
The Microboards CX-1 Disc Publisher is a single drive, 100 disc capacity print and record system. The CX-1
combines industrial strength printing and recording into a single, easy to use duplicator. The system includes
one high-speed DVD recorder. Microboards and HP co-developed the printer technology, allowing up to 4800
x 1200 dpi printing. The Microboards PrintWrite software is a dynamic interface for both beginners and power
users to easily record DVD Video, DVD data, Audio CD’s, Data CD’s, Video CD’s and much more.
Other features include:
•Asynchronous print and record function
•Creation of audio CD’s from MP3, wma or wave files
•Full support for CD Text, Pre-Gap, UPC and ISRC
•Batch mode, allowing multiple masters to be used at a time.
•Integrated print function with prn or SureThing print files, including merge data.
Fully Integrated Automation
Microboards combined our patented auto-loading system with HP's proven inkjet printer technology to give
users the highest output possible, both in image resolution and print speed. Since the CX-1 Disc Publisher is
an auto-loading printer, no calibration of robotics or manual feeding of discs is required. The CX-1 Disc
Publisher connects by a single USB 2.0 interface to your computer.
Flexibility and Speed for Any Application
While the CX-1 Disc Publisher was designed to fill a need in the high-volume arena, it also has the ability to
print at 4800 x 1200 dpi on both DVD and CD media. With the included design software, users can enjoy its
benefits whether making a few discs or a few hundred.
What’s Included
When unpacking your CX-1 Disc Publisher system, the following items should be included:
•CX-1 Disc Publisher
•CX-1 Disc Publisher Quick Start
Guide
•Users Manual (This document)
•Power Cord
•USB 2.0 Printer Cable
•Blank Printable CD’s
•3 Input Bin rods
•100 disc output assembly
•Microboards Disc Publisher Install
CD (Includes Windows hardware
drivers, Printer Toolbox, Disc
Publishing Software, and SureThing
Label software)
•1 V102C Tri-color ink cartridge
•1 V101B Black ink cartridge
•Print Sample
If any of these items are missing, please contact your distributor or Microboards Technology
Technical Support department at 952-556-1639.
The CX-1 Disc Publisher installation disc includes
an Installer that will walk you through the process
step by step. Please perform the installation in
order as specified in the Installer before connecting
to a computer.

6
2
System Requirements
The Microboards CX-1 Disc Publisher has the following minimum requirements and compatibilities:
Supported Operating Systems
Windows XP with SP2, Windows Vista, or Windows 7. 32 and 64-bit OS.
Processor
Pentium 4 (or equivalent) CPU, running at 2.0 GHz or faster.
System Memory
A minimum of 1 GB is required.
Hard Drive Space
Approximately 100 MB of free space is required for the applications and drivers. For storing disc
images, temporary space is needed for the full disc dimension. That could be up to about 800MB for
CD or about 5 GB for DVD.
A separate internal 7200 RPM hard drive is recommended for storing your data. Using the same
hard drive as the operating system can cause the system to perform slowly.
USB Connection
USB 2.0 is required.
Assembly and Installation
Assembly Instructions
CX-1 Disc Publisher Assembly
Remove the CX-1 Disc Publisher system from the shipping box and confirm you received all of the
items.
Place the CX-1 Disc Publisher on a stable, flat surface. You will need
room both in front and behind the system, as discs will be accessed
from both locations.
Open the front door and remove the blue packaging foam from under
the ink carriage.
Install the 2 long input bin posts into the input hopper by screwing them
down onto the screw mounts on the left side of the input hopper. Install
the wide post on the right side of the input hopper.
Install the output bin:
•Align the two holes in the output bin with the holes on
the Front of the printer (numbers 1 and 2).
•Secure the output bin with the two thumb screws.
•The output bin should now be securely in place.
•Next, slide in the 100 disc output spindle into place.
The Output Bin is designed to hang over the front edge of your
work surface.
Plug in the CX-1 Disc Publisher with the AC power cord provided.
Turn on the CX-1 using the switch on the back of the unit.
1

MICROBOARDS TECHNOLOGY, LLC CX-1 DISC PUBLISHER
7
Front Panel Indicators and Buttons
oPower Button – The Power button turns the CX-1 Disc Publisher on and off. It may take a
few seconds for the CX-1 Disc Publisher to turn on after you press the Power button
NOTE: The AC power switch located on the back of the CX-1 Disc Publisher must
be turned on first in order to supply power to the Front Panel.
oPower On LED – This LED will show green when the power to the printer is on.
oCancel Button – Pressing the Cancel button cancels the current print job.
oOut of Media Indicator Button – Pressing this button will clear any media feed issues. This
button has an LED that will flash amber when a media feed issue is occurring.
oOut of Ink LED – This LED will be on if the cartridges are missing or if there is an issue with
either of the cartridges.
Loading Discs
The system will accept CD or DVD 120 mm (12 cm) inkjet printable discs. If the disc does not have
an inkjet printable surface, the ink will not adhere to the surface of the disc. The CX-1 Disc Publisher
will only accept 12 cm discs. Business card or 8 cm discs are not supported by this system.
Figure 1 Figure 2
Load the first 5 or 6 discs flat, as seen in figure 1.
Load the rest of the discs at an angle, against the wide input rod, as seen in figure 2.
The CX-1 Disc Publisher will hold a maximum of 100 discs. DO NOT load more than 100 discs in the
system, as this may cause the discs to load incorrectly.
Power Button Power On LED
Cancel Out of Media
Indicator
Out of Ink LED

8
Installing Ink Cartridges
Supported Ink Cartridges
The CX-1 Disc Publisher uses 1 tri-color ink cartridge and 1 black ink cartridge. The part numbers for
these cartridges are V102C (color) and V101B (black). If other cartridges are installed, the CX-1 Disc
Publisher will not function. These cartridges are available from any Microboards reseller.
Refill kits or non-Microboards ink cartridges are not recommended for use in the CX-1 Disc
Publisher system. Use of non-Microboards cartridges will cause the printer to fail. Use of
refilled cartridges may cause the CX-1 Disc Publisher to fail and may affect your warranty.
Loading / Replacing Ink Cartridges
Cartridges can be changed while the CX-1 Disc Publisher is on. The Out of Ink LED will light if any
cartridge is beginning to run low on ink.
•With the printer on, open the front cover and wait for the print carriage to move to the center
of the printer.
•Lift the cartridge latch by lifting the center of the front of the latch.
•If replacing an empty ink cartridge, remove the cartridge that needs changing by sliding the
cartridge towards the front of the Publisher.
•Remove each new print cartridge to be installed from its packaging.
•Remove the protective covering from the printheads before installing the cartridges.
•Slide the correct ink cartridge into the correct slot – color on the left, black on the right.
•Lower each cartridge latch until it locks into place by applying gentle pressure to the finger
depression. Do not try to force the latch down.
•Close the front cover.
•Wait for the cartridge priming cycle to complete before sending any print jobs to the printer.
The priming cycle will take approximately 70-80 seconds.
Any time you change ink cartridges, you should always wait until the printer has primed the
cartridges before sending it a print job. The priming cycle will take 70-80 seconds to complete
after the door is closed.
Lowering the Cartridge Latch
The latch on the right in is the
correct position. The left latch is
being closed.
Inserting or Removing a Cartridge
After lifting the cartridge latch,
slide the cartridge back to insert,
or forward to remove.

MICROBOARDS TECHNOLOGY, LLC CX-1 DISC PUBLISHER
9
Replacing Empty Ink Cartridges
The CX-1 Disc Publisher will notify you when either cartridge is completely empty. Since the current
print job will be cancelled at that point, it is strongly recommended that you replace the cartridges
when you are notified that they are low rather than waiting until they are empty.
Since the CX-1 Disc Publisher is designed for unattended operation, however, this may not always be
possible. If you see the Out of Ink message on your PC, please perform these steps:
1. Open the front door of the CX-1 Disc Publisher.
2. When the carriage moves to center, remove the ink cartridge specified in the message.
3. Replace the cartridge and close the front door.
4. Press the Cancel button on the front printer control panel.
5. Wait for the printer to prime the cartridge. The priming cycle will
take approximately 70-80 seconds to complete. Do not perform the
next step until the priming cycle completes.
6. After the disc ejects, click the OK button on the Out of Ink message.
7. If this occurs during a Zulu2 action and the cartridge is not replaced immediately, follow the
on-screen instructions that will appear.
Any time you change ink cartridges, you should always wait until the printer has primed the
cartridges before sending it a print job. The priming cycle will take 70-80 seconds to complete
after the door is closed.

10
CX-1 Disc Publisher Installation
The CX-1 Disc Publisher installation disk includes an Installer that will walk
you through the process step by step. Please use the Installer and follow the
installation steps in order.
The following installation sections are intended only as a reference for the installation process, not as
a guide to installing the CX-1 Disc Publisher. Performing the installation out of order could result in
an unsuccessful installation.
The CX-1 Disc Publisher Installation Quick Reference Guide will show you the order in which the
installation will occur.
Installation should always be done when logged in as a user with full Administrator rights.
Windows Component Prerequisites
During the installation process, your PC will be checked to determine if 2 required Microsoft Windows
components are present. If not, these components will be installed. You cannot continue the
installation without installing these necessary Microsoft Windows components.
Connecting to a PC
DO NOT CONNECT YOUR CX-1 DISC PUBLISHER TO A COMPUTER BEFORE
RUNNING THE INSTALLER LOCATED ON THE INSTALLATION DISK!!
The connection between the PC and the Microboards CX-1 Disc Publisher is done with one USB
cable.
1. Confirm that the AC power cord to the back of the CX-1 Disc Publisher is connected and that
the switch in the back is ON.
2. Confirm that your PC is powered on.
3. Connect the square shaped end of the USB cable to the back of the CX-1
Disc Publisher.
4. Connect the flat, rectangular end of the USB cable into a USB 2.0 port in
your PC.

MICROBOARDS TECHNOLOGY, LLC CX-1 DISC PUBLISHER
11
Windows Vista Hardware Installation
The Microboards CX-1 Installer should always be run when logged in as user with full Administrator
rights. This is required for the driver pre-installation to be successful. Once the CX-1 is plugged into
the PC via the USB connection, the hardware will automatically be found and installed on your PC.
During the driver pre-installation, you may need to verify that you would like to install the drivers.
If the Installer is run by a user without full Administrator rights, or you do not verify that the drivers
should be installed, the hardware will need to be installed using the Hardware Wizard. Please follow
the directions below.
Windows XP Hardware Installation
If you are installing the hardware while running the CX-1 Disc Publisher installer, this process will
occur automatically. The Windows Found New Hardware Wizard will appear during any hardware
installation when not using the Installer. Please follow all directions in the order in which they appear.
Turn on power to the CX-1 Disc Publisher and PC.
Once the CX-1 is connected, the operating system will next display the following windows if you are
not running the Installer:
If the Microboards Automation Driver Installation has not been run through the CX-1 Disc
Publisher Installer, the hardware installation may fail.
1. Select No, not this time and click
Next. The following screen will
appear:
2. Click the Next button and the files will
be copied from the CD.
3. If this message appears, click the
Continue Anyway button.
4. Click Finish.
(Continued on next page)

12
5. The following screen will appear:
6. Select No, not this time and click
Next.
7. Click Next.
8. If this message appears, click the
Continue Anyway button.
9. Click Finish to complete the
installation.

MICROBOARDS TECHNOLOGY, LLC CX-1 DISC PUBLISHER
13
Printing Preferences
Access the Printing Preferences by clicking the Start Button on your Windows computer. Select
Settings and then select Printers. Right click on the Microboards PF3 icon, then select Printing
Preferences. There are 7 tabs across the top of the window. Click each tab to see the available
settings.
Color Tab
The Color Tab allows you to
specify that the entire image
should be printed in color or
grayscale. You also have
access to More Color
Options from this tab.
More Color Options
Saturation, Brightness and
Color Tone allow you to fine
tune your print image.
The four ink settings allow you to
change the volumes used of
each specific ink cartridge.

14
Advanced Tab
The Advanced Tab allows you to Enable Maximum dpi setting and adjust the amount of ink placed
on the disc using the Ink Volume and Dry Time settings.
Enabling the maximum dpi will result in longer times to process your print image, reducing
throughput.
To change the Ink Volume or Dry Time settings, click the drop-down box and select Change. A
window will open with a setting bar for the option selected.
Changing the Ink Volume will affect how quickly you need to replace your ink cartridges, but also
affects the quality of the printed output.
Changing the Dry Time can increase or decrease your throughput, but if the Dry Time is set too low,
you risk the possibility that the last disc printed will not have dried before the next disc is placed on
top of it in the output bin.
The default settings are the recommended settings and should be used unless absolutely necessary.
If you choose to increase the Ink Volume, you should also increase the Dry Time.
Diameter Settings Tab
The Diameter Settings tab allows you
to change the size of the print image to
accommodate the variety of printable
surface area available on media.
The Outer and Inner Diameters will
change the size of the area to be
printed. To avoid excessive ink
buildup, these values should never be
set so that the CX-1 Disc Publisher is
printing off the media.
The Parameter Unit should remain on
the 0.1mm setting for maximum
precision.
You can also select one of the preset Mask Types to change the diameter settings.

MICROBOARDS TECHNOLOGY, LLC CX-1 DISC PUBLISHER
15
Ink Tab
The Ink Levels show how
much remains of the color and
black cartridges. The amount
shown as remaining in the
Color cartridge is the individual
color with the lowest level. To
see the individual color level,
click the Advanced Ink Levels
button.
NOTE: If you place a used
cartridge in the CX-1, the ink
level may not be reported correctly. If the CX-1 can identify the
cartridge, it may report the correct ink levels; if not, it will assume that
the ink cartridge is new and will show ink levels of 100%.
Before each disc is printed, the ink levels are checked. If the level of
any one color is has reached 10%, a warning message will be
displayed on your PC and printing will be temporarily suspended. You
can either change the cartridge at this point and click OK, or click OK
to continue printing using the same cartridge.
If you continue with the same cartridge, printing will continue
uninterrupted until the ink level reaches 5%. The low ink level warning
will be displayed once more. Again, either change the cartridge or
continue.
Once the ink level reaches 3% or less, the warning will be displayed
before each print.
It is strongly recommended that you replace the cartridge at this
point.
The Ink Cartridge information includes the re-order part number for the cartridge.
Alignment Tab
Alignment values will move the print image on the disc. Use the graphic on the right side of the tab
as a guideline in how alignment values should be adjusted.
The Resolution setting should always be set at .1mm for best results.
The Outer and Inner Diameters will
change the size of the area to be
printed. To avoid excessive ink
buildup, these values should never
be set so that the CX-1 Disc
Publisher is printing off the media.
The default diameter settings are
1180 for the Outer and 360 for the
Inner when the Resolution is at
.1mm. For hub-printable media, the
Inner diameter should be reduced.
You may need to adjust the
alignment depending on the media
you are using.

16
Print Quality Tab
The Print Quality tab controls the print resolution.
Print Modes
•Text and Graphics
•Photo
Print Quality
•Normal
•Best
•MaxDPI
Printing Recommendations
Text and Graphics mode is used for printing mainly text information and small, simple graphics.
Below are some examples for images in Fast, Normal and Best Modes:
Text and Graphics – Fast Text and Graphics – Normal Text and Graphics – Best
Photo Mode should be used when printing on the entire
disc or when using detailed graphics. Here is an example:
Photo – Normal, Best,
and MaxDPI Modes
About Tab
The About tab provides you with contact information for the worldwide Microboards offices.

MICROBOARDS TECHNOLOGY, LLC CX-1 DISC PUBLISHER
17
The Microboards Printer
Toolbox
To access the Microboards Toolbox, double-click the
toolbox icon located in the tool tray.
Select the Microboards PF3 and click the buttons to
access a particular maintenance function of the Toolbox
for the selected printer.
The Toolbox should be left running at all times in order
to provide you with low ink warnings. Warnings will still
be provided with the toolbox minimized.
Cleaning
The printheads may require cleaning if the printed images show streaks of color. This may occur if
the Disc Publisher has been idle for an extended period of time.
There are 3 levels of cleaning available: Light Clean, Regular Clean, and Heavy Clean.
Light Clean is a low-level cleaning, using the least ink and taking the least amount of time to
complete. Regular Clean uses more ink and takes more time. Heavy Clean uses the most ink and
takes the longest time to complete.
After each of the cleanings, a disc will be printed to verify the cleaning results.
Running this process more than once may be required if the quality does not improve after cleaning
one time.
Pen Calibration
The print pens may occasionally need calibration.
You will need to have 2 blank discs loaded in the
input hopper for this process.
Press the Pen Calibration button. A disc will
print with 4 sets of lines – Black to Color
Horizontal, Black to Color Vertical, Black bidi
Alignment, and Color bidi Alignment. Position
the 4 slide bars in the window shown to the right
based on the line that looks best in each of the 4
printed sets.
Click OK when complete. The second disc will
be printed using the entered pen alignment
values.
This procedure should not be a regular necessity.

18
Automatic Margin Calibration
If the alignment of the discs is severely out of position, use this button to have the printer find the
location of the media.
Place an unprinted disc in the input hopper. Use the same media normally used during printing to
ensure a better calibration.
Press the Automatic Margin Calibration button. The disc will load and the print carriage will first
find the top and bottom of the disc. Next, the disc will move backwards half the diameter of the media
and the left and right sides will be located. The side location will be performed 3 times before the disc
is ejected out the front.
NOTE: The Margin Calibration is not intended to eliminate the Alignment values on the
Printing Preferences Alignment tab. You may need to fine-tune the image position by
using the Alignment values after the margin calibration is complete.
Print Test Disc
Load an unprinted disc in the input hopper prior to clicking this button to print a Test Disc image.
Exercise Belt
This utility should be run if the printer has been idle for an extended period of time, and can be run
multiple times if necessary. The belts will run at high speed for a period of time to recondition the
belts. It is not necessary to load any media for this utility.
Using SureThing Disc Labeler
SureThing Disc Labeler is included with the CX-1 Disc Publisher and will be installed during the CX-1
Installation. For more information on using SureThing, please refer to the SureThing Help menu.
Creating New Labels
Any label you create in SureThing must use the Microboards template to print correctly.
1. To create a new label, either click New Project in the Action window on the left, or select New
from the File menu.
2. Click the Select Label button on the
lower left corner of the dialog that opens
to view the available label templates if
the dialog that opens does not appear as
shown below.
3. Highlight CD/DVD Printers in the Media
Type column.
4. Highlight Microboards in the
Manufacturer column.
5. Select from the options listed in the Label Type column.
We recommend that you use the 17mm inner hole template to ensure that your image will
fully cover the printable surface on both hub printable and non-hub printable media,
adjusting the Diameter Settings when changing between media types (see page 14).
6. Click OK to begin designing the label.
Printing Labels
Select Print from the File menu while the label you want to print is open. Be sure that
you have selected the Microboards PF3 and that CD/DVD Printer is selected in the
Print Using field before clicking the Print button.
If you are printing more than one copy of a label, enter in the number you wish to print before clicking
the Print button.

MICROBOARDS TECHNOLOGY, LLC CX-1 DISC PUBLISHER
19
The CX-1 Disc Publisher Software
Your CX-1 will use either Microboards PrintWrite or Zulu2 as the Disc Publishing software. If your PC
has Windows XP (Service Pack 2 minimum required) or Windows Vista as the Operating System,
PrintWrite will be installed as the default disc publishing software. If your PC is running Windows
2000 Operating System, you will only be given the option of installing and running Zulu2.
Microboards PrintWrite
PrintWrite is not supported on any PC running Windows 2000 as the Operating System.
The first time you launch PrintWrite, you will be asked to confirm the configuration of the CX-1 Disc
Publisher system. This only needs to be done the first time the software is used, or if there is a
change to your hardware.
Please refer to the Microboards PrintWrite User’s Manual for more information on configuring and
operating PrintWrite.
Prassi Zulu2
All printing and burning is done using Zulu2. If you are only printing and not burning, you can
print directly from SureThing. The Print Only feature under the Robotics menu will launch
SureThing.
The first time the user launches Zulu2, the software will ask
you to configure the CX-1 Disc Publisher system. This only
needs to be done the first time the software is used.
When launching Zulu2 for the first time, the following screen
appears:
When the CX-1 Disc Publisher is installed, Windows creates
a new COM port. This new port is used by the CX-1 Disc
Publisher.
Generally, the highest port listed will be the correct
port, and will often be the only port above COM2.
However, if more than one port with a number higher
than 2 appears in the drop-down list, you should
verify which is the correct port before proceeding.
The correct port can be verified through the Device
Manager.
To view the Device Manager, right click on My
Computer from the Windows Desktop or the Start
button menu and select Manage:

20
The Computer Management screen will
appear.
Open up the Ports (COM & LPT)
selection.
You will see an entry labeled
Microboards Automation (COMx)
for each CX-1 Disc Publisher you
have installed. The COMx will be
the COM port number to be
entered into the Configure screen.
Select the COM Port as found on
the Computer Management
screen.
Next, select the Drive. This drive
will be used as the recorder.
Finally, select the Printer.
To confirm you have made the correct selections, you can click on the T box next to each item, as
follows:
•When the Tis pressed for the COM Port, the elevator
will move up and down.
•When the Tis pressed for the recorder, the tray will
open and then close.
•When the Tis pressed for the Printer, the belts will
move in reverse.
Checking the Don’t show this window again box will bypass
the configuration step when launching Zulu2 again. You will
be able to reset this option should it be necessary to configure
the system again. Go to Utilities under the Zulu2 Robotics
menu to re-enable the configuration. It is recommended that
you leave this checkbox unchecked.
Click the OK button.
The system will now initialize the CX-1 Disc Publisher. The belts will be cleared of any discs and any
discs in the recorders will be removed and rejected.
Once initialization is complete, the system is ready for use.