Microtek ScanMaker i800 Plus Instruction Manual

1
Step 2: Install Software
Start Here
Installing your Microtek ScanMaker i800 Plus
Important: Do not remove the yellow stickers from your scanner
until you are told to do so. You must install software before
connecting your scanner.
Always close any open programs, and turn off Anti-virus utilities
before installing software.
Step 1: Unpack Contents
Copyright © 2013 Microtek International, Inc. http://www.microtek.com
I49-004872 B, September 2013
Unpack your scanner package and
check for major components.
1. ScanMaker i800 Plus
2. USB cable
3. Power adapter
4. Power cord
5. Software CDs/DVDs
6. EZ-Lock™ Film Holders
2
1
34
5
6
MAC:
A. Place the Adobe DVD into a drive, and install
the software. Skip this step if you have a
newer version of Photoshop Elements already
installed on your computer.
B. Place the Microtek Software CD/DVD
(ScanPotter) into a drive, and double-click the
ScanPotter installer icon to install ScanPotter.
C. Install the remaining software components,
then restart your computer at the end of all
software installation.
NOTE: After rebooting your Macintosh, the Microtek software will
attempt to locate your scanner on the system. Since this is your
first install and you have not yet connected the scanner, simply
ignore the message that appears and proceed to the next step.
PC:
A. Place the Adobe DVD into a drive, and
install the software. Skip this step if you
have a newer version of Photoshop
Elements already installed on your
computer.
B. Place the Microtek Software CD/DVD into a
drive, and follow the on-screen instructions
to install the scanner driver and software.
C. Restart your computer at the end of all
software installation.
NOTE: If the Microtek Software Installer screen does not come
up automatically, double-click the following in succession: “My
Computer”; the CD-ROM (or DVD-ROM) icon; then cdsetup.exe
to start the installer program.

2
Step 3: Unlock Scanner
Step 4: Connect Scanner
Unlocked
Locked
A. Remove the yellow “Step 3” sticker from
your scanner.
B. With the scanner power off, tilt the back left
corner of the scanner to see the locking
switch at the bottom.
C. Push the locking switch to the position (as
indicated by the graphic on the right), with
the icon on the lock showing as “unlocked”.
D. Raise the scanner lid (TMA), and look for the
locking switch at the base of the TMA.
E. Push the locking switch to the position (as
indicated by the graphic on the right), with
the icon on the lock showing as “unlocked”.
Locked Unlocked
NOTE: To lock the scanner (for shipping and other reasons), refer to
the ScanMaker i800 Plus Supplement.
To the digitizer lid
Make sure the scanner lid (TMA) is properly installed, with
its connector securely connected to the scanner’s 15-pin
accessory port.
To the power adapter
A. Remove the yellow “Step 4”
sticker from your scanner.
B. Connect the power adapter to
the back of the scanner.
C. Plug one end of the power cord
into the socket of the power
adapter, and plug the other end
into a wall outlet or other power
source.

3
To the Hi-Speed USB cable
D. Connect one end of the Hi-Speed
USB cable to your computer.
E. Connect the other end of the Hi-
Speed cable to the scanner’s USB
port.
Step 4: Connect Scanner (cont.)
Power button
Scanner Buttons
The ScanMaker i800 Plus is equipped with six scanner buttons, providing quick access to the most
frequently used functions. These buttons are Scan, Copy, E-mail, OCR,PDF, and Custom.
• Scan: Captures images that can be saved as
files or sent to an image-editing application.
• Copy: Scans the image and sends it to your
printer.
• E-mail: Scans the image and delivers it
directly to your e-mail editor.
• OCR: Scans a text document, converts, and
saves it in text file format.
• PDF: Scans the image and saves it in the
Adobe Acrobat PDF format.
• Custom: Customizes this button to perform
your preferred function, such as Power
Saving, Scan, Fax, or Launch Application.
F. Press the power button at the front panel of
your scanner, and wait for the LEDs to stop
blinking and stay on steady.
The scanner will be detected by your system
automatically.
SCAN
Custom

4
Using theTMA
A.To load film:
1. Load the film inside the EZ-Lock™ Film Holder, with the film’s shiny base facing down.
2. Raise the scanner lid (TMA), and place
the film holder with the loaded film on
the scanner glass bed. Align the arrows
so that the holder is flush against the top
ruler of the scan bed, with the calibration
strip of the holder facing towards the
back of the scanner.
• EZ-Lock 35mm Filmstrip Holder
• EZ-Lock 35mm Slide Holder
• EZ-Lock 4" x 5" Film Holder
• EZ-Lock 6 x 22 cm Film Holder
Do not block
calibration strip
Horizontal ruler
(top ruler)
B. Remove the Black Mat:
Raise the scanner lid, and push the Black Mat
to the side to remove it from the scanner lid.
For more details on the use of the EZ-Lock Film
Holders as well as information on how to scan
non-standard-size film, refer to the ScanMaker
i800 Plus Supplement.

5
Basic Scanning for PC Users
Scanning Photos
1. Place the photo.
To scan a photo, place the photo on the scanner bed. The top end
of the original should be positioned towards the back of the
scanner, with the surface to be scanned facing down.
NOTE: For the automatic cropping feature to work correctly during the preview scan of
your photo, make sure the Black Mat is attached to the scanner lid.
Black Mat
2. Launch ScanWizard EZ.
To launch ScanWizard EZ as a stand-alone program, double-click
the ScanWizard EZ icon on your desktop. When ScanWizard EZ is
launched for the first time, the control panel of ScanWizard EZ - EZ
Mode appears automatically.
3. Scan your material.
Click the Scan button on the control panel of EZ Mode to start scanning.
The ScanWizard EZ will detect the photo on the scanner glass surface first, next automatically
calibrate the scanner, corp the image, and finally perform the image scan with factory settings.
When done, the scanned image can be saved in a file and delivered to the specified location.
Select preferences if necessary
Before you start scanning, specify image settings related to your output image in the
Preferences window according to your preferences.
Auto Settings – Switches on/off Auto-crop and Auto-deskew, and applies ACE
(Automatic Color Enhancement) to the image.
Scan Mode – Sets the image resolution and scan quality to match your target
application.
Save – Assigns the folder location, a file name, and the file format for the output
image.Also, it allows you to specify an application to open the image.
Theme – Changes the appearance of the control panel for the EZ mode.
NOTE: For details about how to use the ScanWizard EZ ‘s Advanced Mode and
Professional Mode, refer to the ScanMaker i800 Plus Supplement.
Press the Scan button
to start scanning
Switches to
the Professional Mode
Switches to
the Advanced Mode
Activates
the Preferences window Minimizes ScanWizard EZ
Exits ScanWizard EZ

6
Scanning Film
1. Place the film.
To scan film, use the film holder. Refer to “Using the TMA” in this guide for more details.
2. Launch ScanWizard EZ.
Follow the step 2 in “Scanning Photos” on previous page to launch ScanWizard EZ.
3. Swtich to ScanWizard EZ - Professional Mode.
Click the Professional Mode button on the control panel of the EZ Mode to switch to the
Professional Mode.
4. In the Preview window of the Professional Mode, click the Scan Material button to choose
Negative Film for negatives; choose Positive Film for transparencies and slides, depending on the
film type you are using.
5. In the Scan Job Queue window, check the “Multiple Auto-crop for EZ Lock Film Holder” option.
6. Click the Overview button to auto-crop and perform a preliminary scan of the film loaded onto the
scanner.
7. Specify your scanning requirements in the Settings window. Choose the desired image type and
resolution, and adjust the scan frame settings if necessary.
8. Adjust image quality if necessary, using the Advanced Image Correction tools.
9. Click the Scan to button in the Preview window to scan the film.
Preview window
Settings window
Scan Job Queue window
Press to swtich to
ScanWizard EZ - EZ Mode
Press to swtich to
ScanWizard EZ - Advanced
Mode

7
Basic Scanning for Mac Users
1. Place the scan material.
A. To scan a photo, place the photo to be scanned on the scanner bed. The top end of the
original should be positioned towards the back of the scanner, with the surface to be scanned
facing down.
NOTE: For the automatic cropping feature to work correctly during the preview scan of your photo, make sure the Black
Mat is attached to the scanner lid.
B. To scan film, use the film holders. Refer to “Using the TMA” in this guide for more details.
2. Launch ScanPotter as a stand-alone by clicking on the program icon, or by selecting it from the
application folder in your Mac OS X system.
3. In the Scan Source options menu, depending on the scan material you are using, choose either
Reflective for photos, Negative Film for negatives, or Positive Film for transparencies and slides.
4. Specify your scanning requirements in the Scanner Settings column.
a) Select the appropriate image type (e.g., RGB Color) in the Color Type as your image output
type.
- Select Color to scan the image in color.
- Select Grayscale to scan the image in grayscale.
- Select Black & White to scan the image in black-and-white.
b) Select a desired resolution in the Resolution for your image output resolution.
c) Select Automatic Detection or a desired dimension in the Scan Frame as your preview image
size.
5. Click the Preview button to perform a preliminary scan of the image in the Preview window.
6. If necessary, resize the scan frame (floating dotted rectangle) around the image by dragging on
the square spots on the edge or on the corner of the scan frame to determine the final size of the
actual scan.
7. If necessary, specify file settings for your output image files, using the options offered in the File
Saving Settings column.
8. If necessary, click the Image Settings button to switch to a window in which you can select a
preset image effect to the image directly or adjust image quality manually by using the additional
image correction tools.
9. Click the Scan button to start scanning.
NOTE: For details on scanning photos and film, see the ScanMaker i800 Plus Supplement in the Microtek Software CD/
DVD.

8
Click the Image Settings button
to switch to a window where
contains a composite display of
nine-image-effects (Filter
column) and additional image
correction tools (Additional
Adjustment column) for your
scanned image.
Click the Scan Settings button to
switch back to the default control
panel of ScanPotter
Scan frame
(enclosed by dotted lines)
Preview window when
scanning slides
Preview
window when
scanning
photos

9
Problems?
The LEDs on the button panel indicate the status of the scanner.
First, make sure that you have followed installation steps 1 through 4. If your problem is listed here,
try the suggested solution.
1. No light comes on when the scanner is turned on.
Make sure your scanner is connected to your computer and plugged into a power source.
2. The “Add/Remove Hardware Wizard” appears on your screen.
Click the “Cancel” button and close the Control Panel. Disconnect the USB cable from the back
of your computer, and refer to the installation instructions in this guide or in the ScanMaker i800
Plus Supplement.
3. When trying to scan, an error message appears on your screen that reads, “Can’t Find Scanners”.
Make sure your scanner is unlocked (see Step 3).
Make sure your scanner is connected to your computer and plugged in to a power source (see
Step 4).
Uninstall and reinstall the ScanWizard EZ or ScanPotter software.
4. After clicking “Scan,” a blank screen appears.
Make sure your scanner is unlocked (see Step 3).
Uninstall and reinstall the ScanWizard EZ or ScanPotter software.
5. Having trouble scanning negatives or slides?
Make sure the scanner lid (TMA) is properly installed, with its connector securely connected to
the scanner’s 15-pin accessory port.
Make sure you place the EZ-Lock Film Holder properly on the scan bed. Do not block the
calibration area (as indicated in the “Using the TMA” section).
From the ScanWizard EZ - Professional Mode, go to the Preview window, then click the Scan
Material button to select either the Positive or Negative Film option.
From the ScanPotter, go to the Scanner Settings column, then click the Scan Source drop-down
menu to select either the Positive Film or Negative Film option.
Uninstall and reinstall the ScanWizard EZ or ScanPotter software.
LEDs
On - Ready to scan
Flashing - Scanning
Off - Scanner is off
Sleep - Power saving
Green
LED
Orange
LED

10
DoYou Need Assistance?
Manuals
If you have additional questions and need further instruction or information, we provide electronic
manuals for:
1. Using your ScanMaker i800 Plus Supplement
2. Using the ScanWizard EZ and ScanPotter scanning software
3. Using the bundled third-party software
To access the electronic manuals: Insert the scanner’s software CD/DVD into your computer’s CD-
ROM (or DVD-ROM) drive. Next, locate and click the “Manuals” option when the software installer
window appears on your screen. Finally, select and click the title of the manual you wish to view.
Missing Items
If your package is missing items, please call Microtek Customer Service Department.
Drivers & Software Upgrades
After you finish the installation of software, if you found that the installed drivers and software cannot
run your product or your computer system properly later, please go to the Microtek Download Service
site at ww7.microtek.com.tw/service.php to download and install any updates you may require.
For additional information about Microtek products, please visit our website at www.microtek.com.
Copyright © 2013 Microtek. Microtek, ScanMaker, ArtixScan, ScanWizard and ColoRescue
are trademarks or registered trademarks of Microtek International, Inc. All other
trademarks or registered trademarks are the property of their respective holders.
Specifications, software and hardware bundles are subject to change without notice.
Delivery of technical support services subject to change without notice. Not responsible
for typographical errors.