Midea FS45-23MRD User manual

FS45-23MRD
USER MANUAL
Warning notices: Before using this product, please read this manual carefully and keep it for future reference.
The design and specifications are subject to change without prior notice for product improvement.
Consult with your dealer or manufacturer for details.
The diagram above is just for reference. Please take the appearance of the actual product as the standard.
STAND FAN

THANK YOU LETTER
Thank you for choosing Midea! Before using your new Midea product, please read
this manual thoroughly to ensure that you know how to operate the features and
functions that your new appliance offers in a safe way.
01
CONTENTS
0
02
1
05
06
07
1 6
1 5
1 7
1 4
1 1
THANK YOU LETTER
SAFETY INSTRUCTIONS
SPECIFICATIONS
PRODUCT OVERVIEW
PRODUCT INSTALLATION
OPERATION INSTRUCTIONS
CLEANING AND MAINTENANCE
TROUBLESHOOTING
TRADEMARKS, COPYRIGHTS AND LEGAL STATEMENT
DATA PROTECTION NOTICE
EN

02
Danger
This symbol indicates that there are dangers to the life and health of
persons due to extremely flammable gas.
Warning of electrical voltage
This symbol indicates that there is a danger to life and health of
persons due to voltage.
Warning
The signal word indicates a hazard with a medium level of risk which, if
not avoided, may result in death or serious injury.
Caution
The signal word indicates a hazard with a low degree of risk which, if
not avoided, may result in minor or moderate injury.
Attention
The signal word indicates important information (e.g. damage to
property), but not danger.
Observe instructions
This symbol indicates that a service technician should only operate and
maintain this appliance in accordance with the operating instructions.
The following safety guidelines are intended to prevent unforeseen risks or damage from
unsafe or incorrect operation of the appliance. Please check the packaging and appliance
on arrival to make sure everything is intact to ensure safe operation. If you find any
damage, please contact the retailer or dealer. Please note modifications or alterations to
the appliance are not allowed for your safety concern. Unintended use may cause
hazards and loss of warranty claims.
Read these operating instructions carefully and attentively before using/commissioning the
unit and keep them in the immediate vicinity of the installation site or unit for later use!
Intended Use
Explanation of Symbols
SAFETY INSTRUCTIONS
EN

Caution
●
●
●
●
●
●
●
●
Read rules for safe operation and instructions carefully.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety. Children should be
supervised to ensure that they do not play with the
appliance.
Keep electrical appliances out of reach from Children or
infirm persons. Do not let them use the appliances
without supervision.
When the appliance is not in use and before cleaning,
unplug the appliance from the outlet.
When the fan was assembled, the rotor blade guard
shall not be taken off anymore.
- Prior to cleaning, unplug the fan.
- The rotor guard shall not be dissembled/opened to
clean the rotor blades.
- Wipe the fan enclosure and rotor blade guard with a
slightly damp cloth.
Never insert fingers, pencils, or any other object
through the grille when fan is running.
Disconnect fan when moving from one location to
another.
Indoor and household use only.
03
EN

●
●
●
●
●
●
●
If the supply cord is damaged, it must be replaced by
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
To protect against the risk of electrical shock, do not
immerse the unit, cord or plug in water or other liquid.
When the appliance is not in use and before cleaning,
unplug the appliance from the outlet.
Ensure that the fan is switched off from the supply
mains before removing the guard.
DISPOSAL: Do not dispose of electrical appliances as
unsorted municipal waste, use separate collection
facilities. Contact your local government for
information regarding the collection systems available.
If electrical appliances are disposed of in landfills or
dumps, hazardous substances can leak into the
groundwater and get into the food chain, damaging
your health and well-being.
For non-user replaceable light sources: The light
sources in this luminaires can only be replaced by the
manufacturer or its service agent or similarly qualified
person.
The battery must be removed from the appliance
before it is scrapped；the appliance must be
disconnected from the supply mains when removing
the battery；the battery is to be disposed of safely；
this appliance contains batteries that are
non-replaceable.
04
Warning
EN

05
SPECIFICATIONS
FS45-23MRDProduct Model
Voltage
Frequency
Power
Rated Current
Power Factor
220-240V~
50/60Hz
25W
0.5A
0.5
EN

PRODUCTOVERVIEW
06
Component Name
NOTE
All thepictures inthis manual are for explanation purpose only.Any discrepancy between
the real object and the illustration in the drawing shall be subject tothe real subject.
Remove parts from the component before performing installation.
Fan head
Install
screw
Tighten
knob
Fan body
Plastic nut
Chassis
Rear grill
Plastic nut
Spinner
Cable terminal
protection box
Blade
Front grill
EN

07
PRODUCTINSTALLATION
Installation Procedures
NOTE
Before installation, first remove chasis screws from the pole, remove the Spinner and
Plastic nut from the motor shaft, and then install.
1 Chassis installation
Alignthelower pole and thechassis, and then fasten securely with chassis screws.
2 Cable terminal protection box installation
2.1 The terminal of the fan head is connected to the terminal of the fan body.
2.2 Put the inserted terminals intotheprotective box and cover the upper protective box.
2.3 Place the protectionbox with theterminal installed into thepipe hole of the fan body.
connecting
terminal male
and female
Protectionbox installation Protective box placement
EN

08
3 Fan head installation
3.1 Install and fix the fan body by way of tightening or loosening install screw.
3.2 Pull out and fix the internal pole (column) after adjusting the height by way of
tightening or loosening the knob.
4 Installation of Rear Grill
Alignthe holes of rear grill withthe protruded points on the motor housing.
5 Installation of Plastic Nut
Screw clockwise the plastic nut tightly to fasten the rear grill.
Install screw Height Adjustment
Height
Adjustment
Key
Clockwise
EN

09
6 Blade installation
After the installation of blade,rotate the blade withyour finger tomake sure the blade
works normally.
7 Spinner installation
Screw counterclockwise the spinner tightly, and then install the front grill.
8 Installation of Front Grill
8.1 From top tobottom alignthe clips of the front grill withthe uppermost mesh of the
rear grill.After the alignment is correct, look from back tofront according tothe
diagram.
Clockwise
Clockwise
Mesh ClipMesh Clip
EN

10
9 Tilt angle adjustment
To adjust the air flow upward or downward, push the grilles lightly to the desired
direction.
10 Oscillation control
To make the fan oscillate, press the clutch knob located on the top of the motor
housing. To get the directional airflow, pull the clutch knob up to its initial position.
8.2 Press the grills in order with both hands. A sound of “click” will be heard when
installed right.
8.3 Self-Catch Installation.
Pa!
Astraightly placed Logo indicates the
grills have been correctly aligned.
Tilt Adjustment
Pull-up for static
Swing Pull-knob
Push-down to swing
EN

11
OPERATION INSTRUCTIONS
Operating Instructions Of The Machine Body
Function descriptionButton
●
●When there is no external power supply, the whole machine is
battery powered. Press the switch button and the whole
machine enters the standby state. Press the switch button again
to disconnect the battery power supply;
When the external power cable is plugged in, press the switch
button to supply power to the whole machine, and the battery
is charged at the same time, the battery level indicator flashes
alternately; Press the switch button again, the power supply of
the whole machine is disconnected, and the battery is no longer
charged.
●In power-on state, press this light adjustment to adjust the light
brightness 3 levels : Strong - Medium - Weak.
●In power-on state,press the wind speed key to select set the
wind speed the following sequence:
level 1 level 2 level 3 ....
level 9 level 0 level 1 level 2 level 3 ....
ON/OFF KEY
TIMER KEY
WIND SPEED
KEY
Light
adjustment
●In power-on state, press this timer key to set the timer:
0h-1h-2h-....9h-0h, The ‘ ’ is lit.
Wind Speed or Timer indicator
Battery Level indicator
Wind Speed
Timer
Light Adjustment
ON/OFF
USB
LED
Timer indicator
EN

12
Function descriptionButton
Remote Control
• The remote control should be normally used within 5 meters of the front of the product
and 30 degrees of the deviation angle.
• The battery contains many heavy metals, acids and bases, etc., which may threaten
human’s health; Waste batteries should be recycled separately.
Forced shutdown
• There is no operation during the running of the fan, after 12 hours of continuous
operation, the fan will be forced to shut down auto-matically.
Additional Functions
●When the machine is powered by battery, the battery icon
shows the current battery power;
In the case of external power charging; the battery icon will
always be displayed as a marquee.
BATTERY
INDICATOR
Function descriptionButtonNO
●Startup/Standby.
●Set the timed shutdown.
1
2
3
4
/●Press “+, -” to set the wind speed or timer.
●Press this “ ” to adjust the light brightness.
3A Battery, 1.5V
Battery
1
3
4
2
EN

13
NOTE
• Use manganese or alkaline batteries of type “AAA”.
• Do not dispose of batteries in fire, batteries may explode or leak.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium)
batteries.
Battery not included in the packaging
1 Slide the battery compartment cover.
2 Insert the batteries, and make sure that the batteries are placed as shown in the Fig 2.
3 Slide back the battery cover.
Fig 2
Fig 1
Fig 3
Batteries Installation
• Do not dispose of batteries in fire, batteries may explode or leak.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium)
batteries.
• Non-rechargeable batteries are not to be recharged.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the product.
• The batteries must be removed from the remote controller before it is scrapped and
that they are disposed of safely.
• The battery needs to be recharged at least once every 6 months.
Batteries Warning As Below
Screen-off function
• In case of no operation for 60 seconds during normal operation, the indicator light on
the body will be automatically off, but the fan will continue to operate. Press the
ON/OFF button to turn off the fan when the screen is off, and press the other button
to restore display.
EN

CLEANING AND MAINTENANCE
14
1. Before cleaning and assembling, unplug the fan power.
2. To ensure adequate air circulation to the motor, keep vents at the rear of the motor
free of dust. Do not disassemble the fan to remove dust.
Please wipe the exterior parts with a soft cloth soaking a mild detergent.
3. Do not use any abrasive detergent or solvents to avoid scratching the surface.
4. Do not use any of the following as a cleaner: gasoline, thinner.
5. Do not allow water or any other liquid entering into themotor housing or interior parts.
6. Be sure to unplug from the electrical supply source before cleaning.
7. Plastic parts should be cleaned with a soft cloth moisten with mild soap Thoroughly
remove soapsuds with dry cloth.
The fan requires minimal maintenance. Do not try to fix it by yourself. Refer it to
qualified service personnel if service is needed.
EN

TROUBLESHOOTING
15
Operation of your appliance can lead to errors and malfunctions. The following tables
contain possible causes and notes for resolving an error message or malfunction. It is
recommended to read the table below carefully in order to save your time and money
that may cost for calling to the service center.
Solution
Cause SolutionProblem
The power cable is not
plugged in or has poor contact.
Make sure the plug is properly
inserted into the socket.
The switch on the body is
not turned on.
Turn on the switch on the
body.
The battery needs replacing. Replace the battery.
The remote is being used more
than 5m away from the fan.
●
●
●
●
The machine does
not work properly
after installed
The remote does
not work Use the remote closer to the
fan and make sure it is pointing
directly at the display panel.
EN

16
logo, word marks, trade name, trade dress and all versions there of are
trademarks, copyrights and other intellectual property rights, and all goodwill derived
valuable assets of Midea Group and/or its affiliates (“Midea”), to which Midea owns
from using any part of an Midea trademark. Use of Midea trademark for commercial
purposes without the prior written consent of Midea may constitute trademark
infringement or unfair competition in violation of relevant laws.
This manual is created by Midea and Midea reserves all copyrights thereof. No entity or
individual may use, duplicate, modify, distribute in whole or in part this manual, or
bundle or sell with other products without the prior written consent of Midea.
All the described functions and instructions were up to date at the time of printing this
manual. However, the actual product may vary due to improved functions and designs.
TRADEMARKS,COPYRIGHTS
AND LEGAL STATEMENT
EN

17
DATA PROTECTION NOTICE
For the provision of the services agreed with the customer,
we agree to comply without restriction with all stipulations of applicable data protection
law, in line with agreed countries within which services to the customer will be delivered,
as well as, where applicable, the EU General Data Protection Regulation (GDPR).
Generally, our data processing is to fulfil our obligation under contract with you and for
product safety reasons, to safeguard your rights in connection with warranty and
product registration questions. In some cases, but only if appropriate data protection is
ensured, personal data might be transferred to recipients located outside of the
European Economic Area.
Further information are provided on request. You can contact our Data Protection
Officer via [email protected]. To exercise your rights such as right to object your
personal date being processed for direct marketing purposes, please contact us via
[email protected]. To find further information, please follow the QR Code.
EN