Midea MVC-V18P Wiring diagram

MVC-V18P
INSTALLATION
INSTRUCTIONS
USER GUIDE
Warning notices: Before using this product,
please read this manual carefully and keep
it for future reference. The design and
specifications are subject to change without
prior notice for product improvement.
Consult with your dealer or manufacturer
for details.
MIDEA
2 in 1
Cordless Handstick
2 in 1
Cordless Handstick
PLEASE READ THE
MANUAL CAREFULLY
BEFORE USING AND
KEEP IT PROPERLY FOR
FUTURE USE
version 01

Charger
2 screws &
drywall anchors
What comes in the carton
Hand vacuum Wall mount
Crevice tool
Wand
2-in-1
upholstery tool

Detachable
hand vacuum
Charging port
Battery
indicator
lights
Release button
for hand vacuum
Wand
Release button
Motorized Brushroll
Dust cup
lever
Filter assembly
(inside dust cup)
Hand vacuum
Bottom lid
Power
button
Handle
Filter cover
How to identify parts of your vacuum cleaner
Cordless vacuum cleaner
One-click
dust cup
release
Low/High
mode
button
Battery
indicator
lights
Easy Rest
nook
Nozzle

4
A
B
1.Slide wand onto hand vacuum
until it clicks (Fig. 1).
2.
nozzle until it clicks (Fig. 2).
• Choose location near power outlet.
Locate point high enough on wall
nozzle to hang freely.
• Place mount against wall and use
pencil to mark drill holes.
• Drill holes (with 1/4” bit) and insert
drywall anchors. Insert screws
through holes on mount and tighten
store accessories
• Place assembled vacuum cleaner
on wall mount.
• Plug charger into power outlet and
then into charger port on handle
(Fig. 4).
• Loop charger cord into clips on
sides of wall mount.
(Fig. 4):
A. Half charged
B. Fully charged
• Indicator lights stop blinking when
fully charged.
• Charge battery fully before using for
six hours.
1
Click!
2
3 Drywall anchors
Cord
clip

!
2. Push
1. Align
1. Click power button once to start (Fig 1).
Vacuum starts on High mode. Use Low/
High button to switch between modes.
back and forth on area to be cleaned.
Avoid oversized or sharp items (such as
screws) with cleaner.
3. Twist wrist to engage swivel function.
4. When done, click power button once to
stop motor.
1. Click the dust cup release button,
located on the front of the handle just
above the dust cup and pull dust cup
out. (Fig. 2).
2. Press lever to release bottom lid of dust
cup to empty debris. (Fig. 2)
3. To place the dust cup back, angle it
forward so the lower hook catches in
the slot and then gently push it back
towards the wand until you hear click
indicating it is locked in place. (Fig. 3)
How to use hand vacuum
and accessories
2
4
1 Power button
3
Crevice tool:
Cleans hard-
to-reach areas
such as corners,
baseboard edges,
dryer vents,
chairs and sofas.
5
CAUTION
The hand vacuum can be used with or
without tools.
• To use without tools, press release
button and remove wand. Collect
debris directly with hand vacuum
nozzle (Fig. 4).
• To use tools with wand, press release
nozzle. Slide tool onto end of wand
until it clicks (Fig. 5).
• To use tools with hand vacuum only,
press release button to remove wand.
Slide tool onto hand vacuum until it
clicks.
Aways turn off hand
vacuum before attaching accessories.
1. Press
2. Pull out
3. Press
Click!

Use with or without wand.
• 2-in-1 upholstery tool: Use
brush to vacuum blinds, vents
or upholstered surfaces. Use
felt portion to clean delicate
surfaces. To switch between
felt and brush portions, press
thumb release and slide brush
up or down.
How to use hand vacuum
Ideal for cleaning stairs.
• Press release button to remove
wand from hand vacuum.
directly to hand vacuum until it
clicks.
• Click power button once to
start. Vacuum starts on High
mode. Use Low/High button
to switch between modes
depending on suction power
desired.

!CAUTION
Make sure vacuum cleaner is turned off and not
plugged into a power source.
WARNING: Do not attempt to remove belt.
24h
4. Click dust cup back into place on unit.
3. Reattach filter and Cyclone.
3. Shake to remove dust.
2. Press other end into slot.
3.
How to maintain brushroll
To avoid unnecessary service calls, periodically check brushroll for debris. If brushrollgets clogged
it will automatically shut off. Turn vacuum off and unplug before attempting to remove clog.
1. Press
2. Pull out
1. Press
2. Pull out
Replace brushroll release tab into slot and press down
to click it into place.
24h
How to maintain your vacuum cleaner
CAUTION
Never operate vacuum
3. Press
in proper position.
WARNING: Moving parts!
Recharge cleaner after
each use.
If debris cannot be removed easily, locate the brushroll release
tab on the right side and open the brushroll cover. Remove the
brushroll and clear any tangled hair and remaining debris.
Dust cup – Empty after each use
Click the dust cup release button, located
on the front of the handle just above the
dust cup and pull dust cup out.
Press lever to release bottom lid of dust cup
to empty debris.
Washable brushroll – clean frequently
To reassemble:
!
dust frequently. Every three months
1. Click the dust cup release button,
located on the front of the handle
just above the dust cup and pull dust
cup out.
2.