Migatronic OMEGA 3 YARD PULSE User manual

QUICKGUIDE
OMEGA³ YARD BASIC
UK
Setting the welding process
Press and hold (11A) to open for setting the welding process. Choose parameter by turning (10).
Set the chosen value by turning (11). To close this function, press (11A) briefly.
Press (12) briefly to turn display of Fxx (F = function) parameter names on/off.
50113783 A
MIG/MAG parameters
Actual welding current (A)
Figure 1
Table 1
Process 1.0 mm 1.5 mm 2.0 mm 3.0 mm
Material Wire Gas S
(m/min)
U0
(V)
S
(m/min)
U0
(V)
S
(m/min)
U0
(V)
S
(m/min)
U0
(V)
Fe 0.8 CO22.5 19.0 4.5 19.5 7.0 21.0 11.0 27.0
Fe 1.0 CO22.0 18.0 2.5 19.0 3.0 20.0 4.5 21.0
Fe 1.2 CO21.0 18.0 2.0 20.0 2.5 21.0 3.5 22.0
Fe 0.8 ArCO23.0 16.0 6.0 18.0 7.5 19.5 11.0 20.0
Fe 1.0 ArCO22.0 15.0 3.0 16.0 4.0 17.0 6.0 19.0
Fe 1.2 ArCO21.5 16.5 2.5 17.5 3.5 18.0 4.5 20.5
Fe 1.6 ArCO21.0 17.0 2.0 18.0 2.5 18.5
CrNi 1.0 ArCO23.0 15.0 4.0 16.0 6.0 17.0 8.5 20.0
CrNi 1.2 ArCO22.0 15.0 3.0 16.0 3.5 16.5 6.0 18.0
AI 1.0 Ar 4.0 14.5 6.0 15.0 7.5 16.0 9.0 19.0
AI 1.2 Ar 3.5 13.0 5.0 15.0 8.0 16.0 9.0 17.0
Process 4.0 mm 6.0 mm 10.0 mm
Material Wire Gas S
(m/min)
U0
(V)
S
(m/min)
U0
(V)
S
(m/min)
U0
(V)
Fe 0.8 CO213.0 29.0 18.0 30.0 24.0 37.0
Fe 1.0 CO26.0 22.5 9.0 24.5 14.0 32.0
Fe 1.2 CO24.5 23.0 7.5 28.5 11.0 36.0
Fe 0.8 ArCO214.0 26.0 18.0 31.0 24.0 33.0
Fe 1.0 ArCO28.0 20.0 11.5 26.5 16.0 30.0
Fe 1.2 ArCO25.5 20.5 8.0 29.0 10.0 32.0
Fe 1.6 ArCO23.0 19.5 4.0 22.0 5.5 29.0
FeFlux 1.2 ArCO26.0 21.0 8.0 25.0 11.0 28.0
CrNi 1.0 ArCO29.0 25.0 10.0 27.0
CrNi 1.2 ArCO28.0 24.0 10.0 24.0 12.0 31.0
AI 1.0 Ar 11.0 22.0 13.0 25.0 15.0 27.0
AI 1.2 Ar 10.0 18.0 13.0 23.0 15.0 26.0
Welding table (set value)
MMA (electrode) parameters
When the MMA welding program is chosen, the operator is
allowed access to the following parameters only
Short circuitSet welding
current (A)
Pr.G / F31 Pre-gas (0.2 sec.)
S.St / F32 Soft start (1.0 m/min.)
bb.t / F37 Burn-Back (5 (0-30))
Po.G / F38 Post-gas (3.0 sec.)
SP.t / F39 Spot time (0.0 sec.)
A
t
S
t1
m/min
SS
t2
t
GS.F / F22 (gas flow) 0,5-27 l/min (only machines with IGC) (optional equipment)
A
t
t
HS.A / F11 Hotstart (25%)
HS.t / F12 Hotstart time (0,5 sek.)
Arc / F13 Arc force (25%)

1 Welding current, [A]
2 Wire feed speed, [m/min]
3 Welding voltage, [V]
4 Arc adjust
5 Lock symbol
Lock: Insert the SD lock card and choose ”1”,
“2” or “All” using (11).
Unlock: Reinsert the SD lock card to unlock
the control panel. For detail information,
see instruction manual.
6 Warning – Overheating
13 MMA welding
Press the key to choose MMA welding.
Long press recalls factory settings if indicator
is on.
14 MIG/MAG welding
Press the key to choose MIG/MAG welding.
Long press recalls factory settings if indicator
is on.
Program is optimised with regard to mix-gas
15 Wire inching
Press the key to feed the wire and adjust
the wire feed speed by turning (10)
simultaneously.
1
BASIC III
AV
61111425
8
10
1
29
11
3
4
14 13 12
6
7
7 Fault indicator
See instruction manual
8Display of wire feed speed or
welding current
9 Display of welding voltage or
Arc adjust
10 Setting wire feed speed or
welding current
Turn the control knob to set the desired
wire feed speed (MIG/MAG) (see table 1) or
welding current (MMA).
11 Setting welding voltage,
Arc adjust and welding process
Turn the control knob to set the desired
welding voltage or Arc adjust (see table 1).
Short press (11A) (MIG/MAG): Change
between display of welding voltage and Arc
adjust.
Long press (11A): Opens for setting the
welding process (see figure 1).
12 Selecting trigger mode
Change between 2-stroke (indicator off) and
4-stroke (indicator on).
2-stroke: The welding process starts when
the torch trigger is activated and ends when
the torch trigger is released.
4-stroke: The welding process starts when
the torch trigger is activated and released
and ends when the torch trigger is activated
again.
Long press: Opens user menu. For detail
information, see instruction manual.
5
11A
QUICKGUIDE OMEGA³ YARD BASIC
15