Minarik VFDP4X04-D230-PCM User manual

0
.
850
[
22
]
6
.350
[
161
]
7.200
[
183
]
0
.1
88
[5
]
5.625
[
143
]
P
O
WE
R
S
PEE
D
FWD
REV
O
F
F
AD
JUS
TABLE
S
PEE
D
REVERSING
AC MOTOR CONTROL
B
O
TT
O
M PLAT
E
2.2
0
[
55.9
]
3
.4
0
[
86.4
]
0.73
[
18.5
]
CO
ND
U
IT H
O
LE
S
2 PLA
C
E
S
ALL DIMENSI
O
NS IN INCHES
[
MILLIMETERS
]
4.56
[
116
]
2.12
[
53.8
]
0
1
2
3
4
5
6
7
8
9
1
0
Variable Frequency Drive for
3-phase & single phase AC motors
QUICK START GUIDE
VFDP4X04-D230-PCM
DIMENSIONS
SPECIFICATIONS
1-Phase Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .* 115/230 VAC
1 or 3 -Phase Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230 VAC
Maximum Horsepower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 HP
Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.0 AC
AC Amps In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 / 10 amps
AC Voltage Input Range . . . . . . . . . . . . . .115/230 VAC ± 10%, 50/60 Hz single phase
Standard Carrier Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 KHz
Adjustable Braking Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 - 4 ADC
Adjustable Braking Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 - 10 Sec.
Adjustable Minimum Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 - 30 Hz
Output Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 - 120 Hz
Adjustable Maximum Output Frequency Range . . . . . . . . . . . . . . . . . . . . .30 - 120 Hz
Acceleration Time Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 - 12 secs
Deceleration Time Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 - 12 secs
Analog Input Voltage Range (S1 [-] to S2 [+]) . . . . . 0 - 5 VDC, 0 - 10 VDC, 4 - 20 mA
Input Impedance, S1 to S2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .~ 100K ohms
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.5G max (20 - 50 Hz)
0.1G max (> 50 Hz)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.2 lbs
Ambient Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . .10° - 40° C
* Jumper settings MUST
match input line voltage.
Application of 230 VAC
line input when jumpers
are set for 115 VAC will
result in severe damage
to the drive.
1. Remove the six (6) phillips screws on the
front case.
NOTE: The two shorter screws (#6 - 32 x 2
1/2) on the front case are used at hole
locations 5 & 6.
2. Remove the five (5) phillips screws on the
bottom plate.
NOTE: DO NOT REMOVE the three (3)
screws securing the bottom plate to the
heatsink.
P
O
WE
R
S
PEE
D
FWD
REV
O
F
F
ADJUSTABLE SPEED
REVERSING
AC MOTOR CONTROL
B
O
TT
O
M PLAT
E
D
O
N
O
T REM
O
V
E
THE THREE
(
3
)
SCREWS SECURIN
G
THE B
O
TT
O
M PLATE T
O
THE HEAT
S
IN
K
12
5
6
34
1
2
4
3
5
0
1
2
3
4
5
6
7
8
9
1
0
REMOVING THE
CASE COVER

STEP #4
Configure jumpers JMP501 and JMP502 on the bottom board for 115 or 230 VAC Power Input.
J
MP
502
J
MP
501
STEP #2
Configure jumpers JMP504 and JMP505 on the top board for the appropriate signal input.
J
MP
50
4
1 2
3
1 2
3
J
MP
505
1 2
3
J
MP
505
JMP504 (on top board)
Pins 1 & 2 for Voltage Input, or using a speed pot.
Pins 2 & 3 for Current Input
JMP505 (on top board)
Pins in Column 1 for 0 - 5 VDC Voltage Input,
or using a speed pot
Pins in Column 2 for 0 - 10 VDC Voltage Input
Pins in Column 3 for 4 - 20 mA Current Input exam
p
le
:
STEP #3
Configure jumpers JMP503 on the bottom board and JMP506 on the top board.
J
MP
503
JMP503 (on bottom board)
Pins 1 & 2 to Trip
Pins 2
&
3 to Restar
t
TRIP: Drive has a low volta
g
e fault & mus
t
be manuall
y
re-enabled to restart
.
RESTART: Drive has a low volta
g
e fault
&
will momentaril
y
stop then auto-restar
t
when input volta
g
e returns to minimum level
.
U
V TRIP
R
E
S
TAR
T
1
2
3
J
MP
506
JMP506 (on top board)
Pins 1 & 2 to Brake
Pins 2 & 3 to Coast
BRAKE
CO
A
ST
1
2
3
CONNECTIONS
STEP #5
Connect motor leads of a 3-
phase motor to U, V, and W
(TB502 on BOTTOM board)
using 14 - 16 AWG wire as
shown in the figure below.
STEP #6
Connect 115 or 230 VAC power
input using 12 AWG wire.
NOTE: Minarik strongly
recommends installing an
emergency stop switch on both
the L1 and L2 inputs.
STEP #1-skip this step if provided FWD/OFF/REV and speed potentiometer will be used.
Otherwise disconnect factory-wired connections from the FWD/OFF/REV switch and speed
potentiometer. Connect the enable/disable switch, direction switch, and speed potentiometer or
signal input to TB501 on the TOP board using 20 - 24 AWG wire as shown below.
DIRECTION
SWITCH
ENABLE/DISABLE
SWITCH
(open to disable)
NOTE:
The
f
actor
y
-wired spee
d
potentiometer on the
case cover must be
disconnected prior to
wirin
g
to a si
g
nal input
TO SPEED POT
OR SIGNAL INPUT
Copyright 2003 by Minarik Corporation - All rights reserved. No part of this document may be reproduced or transmitted in any form without
written permission from Minarik Corporation. The information and technical data in this document are subject to change without notice.
Minarik Corporation and its Divisions make no warranty of any kind with respect to this material, including, but not limited to, the implied
warranties of its merchantability and fitness for a given purpose. Minarik Corproation and its Divisions assume no responsibility for any errors
that may appear in this document and make no commitment to update or to keep current the information in this document. mvd092503
MINARIK DRIVES
www.minarikdrives.com
14300 De La Tour Drive, South Beloit, IL 61080; Phone: (800) MINARIK (646-2745); Fax: [phone]
Document Number: 250-0379, Revision 0; Printed in the U.S.A. - September 2003