Mitsubishi Electric PZ-61DR-E User manual

Prior to use, thoroughly read the instructions in this manual to use the product correctly.
Retain for future reference.
Make sure that this manual, CD-ROM and Installation Manual are passed on to any future
users.
To ensure safety and proper operation of the remote controller, the remote controller should
only be installed by qualified personnel.
English
Deutsch
Français
Español
Italiano
Nederlands
Português
Svenska
Ɋɭɫɫɤɢɣ
Türkçe
Lossnay Remote Controller
MODEL
PZ-61DR-E
Simple operation manual
1408875HK9901

2
WARNING
Thoroughly read the following safety precautions before using the unit.
Observe these precautions carefully to ensure safety.
CAUTION
Indicates a risk of death or serious injury.
Indicates a risk of serious injury or structural damage.
WARNING
Safety precautions
After reading this manual, pass it on to the end user to retain for future reference.
Keep this manual for future reference and refer to it as necessary. This manual should be made available
to those who repair or relocate the controller. Make sure that the manual is passed on to any future
users.
General precautions
To reduce the risk of electric shock, malfunctions,
smoke or fire, do not operate the switches/buttons or
touch other electrical parts with wet hands.
To reduce the risk of shorting, current leakage,
electric shock, malfunctions, smoke, or fire, do not
wash the controller with water or any other liquid.
Do not install the unit in a place where large
amounts of oil, steam, organic solvents, or corrosive
gases, such as sulfuric gas, are present or where
acidic/alkaline solutions or sprays are used
frequently. These substances can compromise
the performance of the unit or cause certain
components of the unit to corrode, which can result
in electric shock, malfunctions, smoke, or fire.
When disinfecting the unit using alcohol, ventilate
the room adequately. The fumes of the alcohol
around the unit may cause a fire or explosion when
the unit is turned on.
To reduce the risk of injury or electric shock, before
spraying a chemical around the controller, stop the
operation and cover the controller.
To reduce the risk of injury or electric shock, stop
the operation and switch off the power supply before
cleaning, maintaining, or inspecting the controller.
If any abnormality (e.g., burning smell) is noticed,
stop the operation, turn off the power switch, and
consult your dealer. Continued use of the product
may result in electric shock, malfunctions, or fire.
Properly install all required covers to keep moisture
and dust out of the controller. Dust accumulation and
water can cause electric shock, smoke, or fire.
CAUTION
To reduce the risk of fire or explosion, do not place
flammable materials or use flammable sprays
around the controller.
To reduce the risk of damage to the controller, do not
directly spray insecticide or other flammable sprays
on the controller.
To reduce the risk of environmental pollution, consult
an authorized agency for proper disposal of remote
controller.
To reduce the risk of electric shock or malfunctions,
do not touch the touch display or buttons with a
pointy or sharp object.

33
To reduce the risk of injury and electric shock, avoid
contact with sharp edges of certain parts.
To avoid injury from broken glass, do not apply
excessive force on the glass parts.
To reduce the risk of injury, wear protective gear
when working on the controller.
Precautions for moving or repairing the controller
WARNING CAUTION
The controller should be repaired or moved only by
qualified personnel. Do not disassemble or modify
the controller.
Improper installation or repair may cause injury,
electric shock, or fire.
To reduce the risk of shorting, electric shock, fire,
or malfunction, do not touch the circuit board with
tools or with your hands, and do not allow dust to
accumulate on the circuit board.
Additional precautions
To avoid damage to the controller, use appropriate
tools to install, inspect, or repair the controller.
Do not pull or twist the communication cables.
Pulling or twisting a cable may result in fire or
equipment failure.
To avoid discoloration, do not use benzene, thinner,
or chemical rag to clean the controller. To clean the
controller, wipe with a soft cloth soaked in water with
mild detergent, wipe off the detergent with a wet
cloth, and wipe off water with a dry cloth.
This controller is designed for exclusive use with
the Lossnay by Mitsubishi Electric. The use of this
controller for other systems or for other purposes
may cause malfunctions.
To avoid damage to the controller, provide protection
against static electricity.

4
Names and functions of controller components
Controller interface
Press to turn ON/OFF the Lossnay unit.
1ON/OFF button
This lamp lights up in green while the unit is in
operation. It blinks while the remote controller
is starting up or when there is an error.
Press to save the setting.
Main menu: Press to move the cursor down.
Press to return to the previous screen.
Main display: Press to change the fan speed.
Main menu: Press to move the cursor up.
Press to bring up the Main menu.
Main display: Press to change the ventilation mode
Main menu: Press to go to the previous page.
Operation settings will appear.
When the backlight is off, pressing any
button turns the backlight on and it
will stay lit for a certain period of time
depending on the screen.
Main menu: Press to go to the next page.
* If LOSSNAY does not have the function
or operation is not possible, the operation
guide is not displayed.
6ON/OFF lamp
2SELECT button 7Function button F1
3RETURN button 8Function button F2
4MENU button 9Function button F3
5Backlit LCD
0Function button F4
When the backlight is off, pressing any
button turns the backlight on and does
not perform its function. (except for the
ON/OFF button)
Main
Main display:Return button
Cursor Page
Main menu
Timer
Weekly timer
Restriction
Filter information
Error information
1/2
Lossnay 12:00 Sun
Outdoor
0°C
Return
20°C
Supply
15°C
Fan Mode
Auto
The functions of the function buttons
change depending on the screen. Refer
to the button function guide that appears
at the bottom of the LCD for the functions
they serve on a given screen.
When the system is centrally controlled,
the button function guide that corresponds
to the locked button will not appear.
Function buttons Main display Main menu
Function guide
5
6
1234
7 8 9 0
7 8 9 0 7 8 9 0

5
Lossnay 12:00 Sun
Outdoor
0°C
Return
20°C
Supply
15°C
Fan Mode
Auto
1
5
6
9b a0 e f
7
8
c
3d g
4
2
h
Display
Fan speed setting appears here.
3 Fan speed
Appears when the night-purge function is
available.
Appears when performing operation to protect
the equipment.
Appears when the ON/OFF operation is centrally
controlled.
Current time appears here.
Appears when the buttons are locked and/or a
fan speed is skipped.
Lossnay is always displayed.
a
b
5
8
1 Remote controller name
Indicates the ventilation mode setting.
d Ventilation mode
Appears when external fan speed operation.
Appears when operation interlocked with external
unit.
Appears when the On/Off timer, or Auto-off timer
function is enabled.
e
f
9
Indicates when filter and/or Lossnay core needs
maintenance.
Appears when the filter reset function is centrally
controlled.
7
6
Appears when the Weekly timer is enabled.
0
Appears when external ventilation mode
operation.
Displays the outdoor temperature, return
temperature, and supply temperature (calculated
value).
g
hTemperature
Functions of the corresponding buttons appear
here.
4 Button function guide
Appears when performing the power supply/
exhaust function or the delay operation at the
start of operation.
c
* All icons are displayed for explanation.
2 Clock
(See the Installation Manual.)

6
Power ON/OFF
Fan speed
Ventilation mode
Basic operations
Press the ON/OFF button.
The ON/OFF lamp will light up in green, and the
operation will start.
Press the ON/OFF button again.
The ON/OFF lamp will go out, and the
operation will stop.
ON
ON
ON
OFF F1F2F3F4Lossnay 12:00 Sun
Fan Mode
Auto
F1F2F3F4Lossnay 12:00 Sun
Auto
Fan Mode
Press the F2 button to go through the fan
speeds in the following order.
Operation is not possible during external fan
speed operation.
A fan speed that is skipped because of a fan skip
setting is not displayed.
Press the F3 button to go through the
Ventilation mode in the following order.
Operation is not possible during night-purge
operation and external ventilation mode
operation.
AutoAuto

7
Maintenance
Filter information
Lossnay 12:00 Sun
Fan Mode
Auto
will appear on the Main display when it is
time to clean the filter and/or Lossnay core.
Clean, or replace the filter and/or Lossnay
core when this sign appears.
Refer to the Lossnay unit Instruction Manual
for details.
1 2
3 4
F1F2F3F4Main
Main display:
Cursor Page
Main menu
Timer
Weekly timer
Restriction
Filter information
Error information
1/2
Select “Filter information” from the Main
menu , and press the SELECT button. F1F2F3F4Main menu:
Filter information
Reset
Filter
Lossnay core
Please clean the parts above.
Then press reset button.
Press the F4 button to reset cleaning
sign.
Refer to the Lossnay unit Instruction
Manual for how to clean the filter and/or
Lossnay core.
F1F2F3F4Filter information
OK
Cancel
Reset cleaning sign?
Filter
Lossnay core
Filter information
Cleaning sign reset
Main menu:
Select “OK” with the F4 button. A confirmation screen will appear.
When the is displayed on the Main display the system is centrally controlled and the
cleaning sign cannot be reset.

8
Troubleshooting
Timer, Weekly timer
When an error occurs, the following screen will appear.
Check the error status, stop the operation, and consult your dealer.
F1F2F3F4Error information
Error code 5101
Error unit LC(Lossnay)
M-NET address 1
Model name LGH-100RVX-E
Serial No. 01234567
ResetPage
Error information
Contact information
Dealer
Tel [phone]
ResetPage
Reset error:Reset button
Reset error: Reset button
1/2
2/2
Error code, error unit, M-NET address, unit
model name, and serial number will appear.
The model name and serial number will appear
only if the information have been registered.
Press the F1 or F2 button to go to the next
page.
Contact information (dealer's phone number) will
appear if the information have been registered.
blinks
The settings for Timer and Weekly timer operation can be made from the remote controller.
Press the MENU button to go to the Main menu, and move the cursor to the desired setting
with button F1 or F2 . Refer to the Instruction Book of the remote controller for further
information.
F1F2F3F4Main
Main display:
Cursor Page
Main menu 1/2
Timer
Weekly timer
Restriction
Filter information
Error information
Timer
On/Off timer
Operation On/Off times can be set in
5-minute increments.
Auto-Off timer
Auto-Off time can be set to a value from 30
to 240 in 10-minute increments.
Weekly timer
Operation On/Off/Night-purge times for a
week can be set.
Up to eight operation patterns can be set for
each day.
Error information F1F2F3F4Main
Main display:
Cursor Page
Main menu 1/2
Timer
Weekly timer
Restriction
Filter information
Error information