MJ LED LIGHTNING MJ-A380 User manual

380W MOVING HEAD LIGHT
BEAM SPOT WASH(3IN1)
MJ-A380
User manual
======PROFESSIONAL STAGE LIGHTING ========
Thank you for choosing our beam spot wash moving head light. For the sake
of your safety, Please read and follow these instructions carefully and keep
this manual ina safe place for future reference.

BEAM SPOT WASH (3IN1) 380W BEAM SPOT WASH (3IN1) 380W
Catalogue
Chapter Page
Safe Usage Of The Product -------------------------------------------------------------1
Install The Equipment -------------------------------------------------------------------2
Fitting The Lamp-------------------------------------------------------------------------2
Power Code Connection ----------------------------------------------------------------3
DMX Connection ------------------------------------------------------------------------3
DMX Terminator ------------------------------------------------------------------------4
Function Set ------------------------------------------------------------------------------5
Operation Menu --------------------------------------------------------------------------7
Description of manual control or programming function--------------------------10
Maintenance -----------------------------------------------------------------------------12
Keeping The Product Clean -----------------------------------------------------------13
Trouble Shooting------------------------------------------------------------------------13
Equipment and Appendix--------------------------------------------------------------14
Channel List------------------------------------------------------------------------------14
Technical Parameters--------------------------------------------------------------------18
☆
Important notice:
·In this instruction for use contains about the installment and the use aspect
important information of the beam moving head. When installing and using, you need
to look this usage instruction strictly.
·Before open the beam moving head and if you want to do the repair work, please
make sure the power source is at the separation condition.
·Every unit is tested completely and packed properly by the manufacturer. Please
make sure the packing and the unit are in good condition before installation and use.
Should there be any damage caused by transportation, consult your dealer and do not
use the unit. Any damage caused by improper use will not be assumed by the
manufacturer or dealer.
Attention: Unceasingly carries on the product improvement about our company
the policy, in this instruction booklet carries the data will have the possibility to be able
to change in the future, when no longer separate notice change matters concerned.
Our company retains when the product improvement changes the related specification
the authority.
SAFE USAGE OFTHE PRODUCT
When unpacking and before disposing of the carton, check there is no transportation
damage before using the product. Should there be any damage caused by
transportation, consult your dealer and do not use the apparatus.
The product is for indoor use only, IP20. Use only in dry locations. Keep this device
away from rain and moisture, excessive heat, humidity and dust. Do not allow contact
with water or any other liquids.
The product is not designed or intended to be mounted directly on to inflammable
surfaces
The product is only intended for installation, operation and maintenance by
professional person.
The product must be installed in a location with adequate ventilation, at least 50cm
from adjacent wall surfaces. Be sure that no ventilation slots are blocked.
Do not product the beam onto inflammable surfaces, minimum distance is 12m.
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the
power requirements of the projector.
It is essential that each projector is correctly earthed and that electrical installation
conforms to all relevant standards.
Do not connect this device to any other types of dimmer apparatus.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never
let the power-cord come into contact with other cables. Only handle the power-cord
by the plug. Never pull out the plug by tugging the power-cord.
Keep the light clean. Do not touch the light glasss with bare hands.
The product should always be installed with a secondary safety fixing. On the
projector base brink, there is a hole for the safety cord provided. It should be attached
as shown in “installing the projector” section.
The lamp used in this projector is a discharge lamp. After switching off don,t attempt
to restart the projector until lamp has cooled, this will require approx 15 minutes.
Switching the lamp on and off at short intervals will reduce the life of both the lamp
and the projector. But occasional breaks will prolong the life of the lamp and projector.
Never run the projector without a lamp.
The light shall be changed if it has become damaged or thermally deformed or
reached its life limit.
Shields and lens shall be changed if they have become visibly damaged to such an
extent than their effectiveness is impaired, for example by cracks or deep scratches.
Exterior surface temperatures of the luminaire after 5 minutes operation is 70° 。，
when steady state is achieved 140°。
There is no user serviceable parts inside the projector, do not open the housing and
never operate the product with the covers removed.
If you have any questions, don’t hesitate to consult your dealer or manufacturer.
★Always disconnect from the mains, when the device is not in use or
before cleaning it or before attempting any maintenance work !
1

BEAM SPOT WASH (3IN1) 380W BEAM SPOT WASH (3IN1) 380W
Install The Equipment:
Use 2pcs clamp and 1safety cord(need to purchase).Use clamp fix with light hook
which in the packing box with light, then use screw install to the bottom of lamp. Hang
the fixture on the structure and fasten the screws attached to each clamp. Make sure
the light is installed reliable, and confirm the light which you fixed is strong enough for
hanging the light. Base on safety reason, please according to the above picture using
safety wire cross the light to make it strong enough again.
Warning!
1. Unlock the PAN and TILT before the 1st application of the light for safety.
2. Hook and clamp only use for hanging the light. Do not use clamp as a tool to move
fixtures.
3. Base on safety reason, please use the safety cord which can afford the weight ten
times of lamp through Insurance hole for auxiliary hanging.
4. Don't use the handle of the moving head light to fixed or lift!
Fitting The Lamp
：
.Loosen 8 fast-fit screws and remove the plastic cover, when fitting/replacing the lamp.
.Do not touch the bulb of the new lamp with bare hand so as not to influence the beam
output.
.Do not harm the sticking out point of the lamp during its installation.
.Fit new lamp and close the plastic cover by 8 fast-fit screws when finished lamp
installation.
2
.Lamp work will reach a very high temperature, Vapor discharge lamp can not
continue to supply this physical characteristics, therefore, the power completely cool
for 20 minutes before on the operation. Failure to do so will lead to a high-pressure
discharge and short circuit burned out the computer's control panel components.
Notes: Unplug the light from power before lamp installation or replacement and
wait for it to cool.
Power Code Connection:
Connect the power cord as follows:
L (live) =brown
E (earth) =yellow/green
N (neutral) =blue
Use the plug provided to connect the mains power to the projector paying attention to
the voltage and frequency marked on the panel of the projector. It is recommended
that each projector be supplied separately so that they may be individually switched
on and off.
★
It is essential that each projector is correctly earthed and the
electrical installation conforms to all relevant standards.
★
Please do NOT connect the power cable hand by hand over 2pcs.
DMX Connection:
Connection between the controller and a projector and between one projector and
another must be made with a 2 core-screened cable, with each core having at least a
0.5mm diameter. Connection to and from the projector is via cannon 3 pin (which are
included with the projector) XLR plugs and sockets. The XLR's are connected as
shown in the figure above.
Note: Care should be taken to ensure that none of the pins touch the metallic body of
the plug or each other. The body of the plug is not connected in any way. The XLED
590 accepts digital control signals in protocol DMX512 (1990).
Connect the controller’s output to the first fixture’s input, and connect the first fixture’s
output to the second fixture’s input and connect the rest fixtures in the same way.
Eventually connect the last fixture’s output to a DMX terminator as shown in the
figure below.
3

BEAM SPOT WASH (3IN1) 380W BEAM SPOT WASH (3IN1) 380W
DMX Terminator:
In the Controller mode, at the last fixture in the chain, the DMX output has to be
connected with a DMX terminator. This prevents electrical noise from disturbing and
corrupting the DMX control signals.
The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor
connected across pins 2 and 3, which is then plugged into the output socket on the
last projector in the chain. The connections are illustrated below.
Function Set
4
Light panel schematic diagram is shown in Picture. Above title display light name.
Below is the status bar,show current light signal, lamp status, fault(When there is a
fault message not viewed, display“ERR”，no is display “NOR”). etc.
This light supports the DMX/RDM protocol. When the light is searched by the RDM
host, the panel will display the three letters "RDM". ------------
Display and operation are similar to "Android operating system", use your fingertips
or blunt hard objects to click on the corresponding item to operate.
Note: Do not use sharp or sharp objects to click on the display to prevent damage.
Operation Menu
1. Operate the light with an intuitive touch or an auxiliary input
(touch-enabled product)
The left area is the TFT display area and the touch area，click on the panel
content with your finger or blunt hardware, then you can complete the
parameter setting or view status.
The right area is the auxiliary input, if you do not use the touch function that
comes with the TFT, you can use the auxiliary input to select the item you
want to set or view to complete the operation.
2. Parameter value input
When the selected parameter item needs to input a value, the window shown in
picture will open as below:
Set the value: You can pull the slider directly to quickly set the desired
value, you can also click the “Up” or “Down” button on the right to set the
desired value precisely or use the auxiliary input to set it.
Application value: When setting the data with the "Up" or "Down" buttons,
the value is sent to the fixture immediately, but the value is not saved.
Save the value: at any time, click the "OK" button in the lower right
corner,then save the current value to the internal storage. The next time
you turn it on, the saved value is applied to the fixture.
5

BEAM SPOT WASH (3IN1) 380W BEAM SPOT WASH (3IN1) 380W
In the parameter setting interface, you can quickly switch to other setting
interface by pressing the blue option on the left.
1. Set the DMX address code
The DMX address, channel mode, etc. of the light can be set through the page
shown in Figure 1-1.The menu settings of the light optimize the setting of the
address, several settings for address codes are as follows:
Select “last light” or next light”, the fixture will be based on the current
address code and channel data. Automatically calculate the address code
of the next or previous station ,can be set quickly;
Click on the address code value, Can enter the value editing window, Here
you can set any valid address code. The light automatically obtains the
current DMX channel of the light. Automatically filter unusable address
codes (512 - current channel number).
The light supports the RDM protocol. The fixture address code can be set
remotely via RDM. Provide two buttons:
Channel mode: 20/24different channel modes can be cycled;
Lamp reset: reset all motors.
2. Set the light work mode
You can set the light control mode and lamp control by the page shown in
Figure 1-2.The light supports 4 control modes(DMX mode, auto running
mode, voice control mode and scene mode). For detailed parameter value
setting, please refer to the previous section. The specific parameters are
described in the following table:
Work mode
DMX Ctrl
Control mode
，
receive DMX signal
，
RDM signal
Auto Run
The light runs automatically according to the built-in program
Sound Ctrl
When the luminaire detects a strong sound, the fixture
automatically runs a scene in accordance with the built-in
program. Otherwise keep the last scene.
Scene Mode
Run in the set scene mode, support up to 10 scenes of custom
editing
1~10
Output the specified scene
Auto Automatically loops the scene in the set scene time
(non-
zero), and the scene with time 0 automatically
skips the ignore.
7
3. Set the Boolean parameter
When the set parameter is Boolean (such as ON or OFF), then directly click
on the corresponding item to switch the parameter value. This type of
parameter will be saved to the internal storage after modification. Press the
parameter option on the right, the corresponding option will be grayed out.
When the hand is released, the corresponding parameters are changed and
saved. If the parameter option is pressed, it is not the parameter you want to
change. At this point, you can move your finger to other parts of the screen.
The corresponding parameters will not change.
The determination of important Boolean parameters will pass, Determine the
window to set, as shown in picture below:
4. Subpage (parameters)
5. Function operation and parameter setting
Enter the settings interface, as shown in Figure 1-1:
In the main interface, you can enter the corresponding parameter setting
interface by selecting six buttons.
6

BEAM SPOT WASH (3IN1) 380W BEAM SPOT WASH (3IN1) 380W
Screen Rot
Set the display orientation of the screen
Forward Don’t reverse display
Reverse Reverse display
Auto
Automatically detect the direction of the light hanging
light, automatically switch the display direction
DMX
Instruction
Set the indication mode of the DMX signal indicator
Mode 1
Bright when there is a signal, and goes off when there
is no signal
Mode 2
Goes Off when there is a signal, bright when there is
no signal
Mode 3
Flicker when there is a signal, and goes off when
there is no signal
Touch
screen
switch
Select whether to disable the touch screen, when the screen touch
is accidentally damaged, you can disable the touch function and set
the light fixture with the auxiliary input.
Touch
correction
When the screen touch is not accurate, you can enter the
correction page correction screen.
For touch-enabled light, if there is a bad touch, you can enter the calibration page to
re-correct the touch accuracy of the touch screen. Under normal circumstances,
please do not enter this page. If the touch is damaged, select Disable touch switch.
4. Scene editing mode
Enter the page shown in Figure 1-4. The light enters the scene editing mode.
Under this page, the light does not receive the DMX controller data, and the
edited data is immediately reflected on the luminaire.
The content of the page is not indented depends on the currently selected
channel, and the displayed channel content and order are consistent with the
light channel table. Through this page, 10 scenes can be edited, as shown in
the following table:
Scene mode
Scene selection Select the current operation scene
1~10 10 scene change
Scene time
Set the retention time of the current scene when it is
automatic, in units of 0.1 seconds.
0
The current scene does not participate in
automatic scene output
1-255 0.1 second to 25.5 seconds
9
M/Schoose
Effective in non-
DMX mode, select the mode of data output, The
light automaticall
y detects the DMX status and automatically
switches the output to prevent data conflicts.
Master The light runs as built-in，If the DMX has no signal, then
output data (synchronized), otherwise no data is output
Slave The light runs in built-in mode and no output data (not
synchronized with other luminaires)
Auto If the DMX has no signal, the light operates as built-in.
Otherwise, the light works according to the DMX signal.
Light Switch
(bulb light source) pops up a confirmation dialog box, Select
"SURE" to confirm the current operation, turn the lamp on or off,
and the switch interval is limited to 30 seconds.
OFF
Current lamp output is off
ON
The current light output is already on
Scene mode for single or small fixtures, just output a fixed scene, or need to run a
simple program,can not be
connected to the console, edit it in the scene page.
If the light source is light bulb, after turning off the light bulb, please wait 10 minutes
before turning on the light bulb.
3. Panel display settings
The light support Chinese and English language, upside down display, etc.,
enter the corresponding parameter settings as shown in Figure 1-3. The
specific menu contents are as follows:
Display mode
Language
Set the displayed language
English
English display
Chinese
Chinese display
Screen
Saver
Set the screen display content or mode after no operation for 30
seconds
OFF
Keep the last action page, bright screen
Mode 1
Off screen
Mode 2
Black screen, showing the address code of the
current fixture in the lower left corner
Mode 3
Display trademark information, address code and
operation mode
8

BEAM SPOT WASH (3IN1) 380W BEAM SPOT WASH (3IN1) 380W
Pan 0-255 Set the data of each channel, and the display
content and s
equence correspond to the
channel table of the light
……
0-255
……
0-255
Function
0-255
If the reset channel in the scene edits the valid reset data, the light will reset, but after
reset, thevalue of the corresponding reset channel will be automatically cleared to
prevent multiple consecutive resets.
Check the page to get the current channel table order of the light. For detailed channel
data, please refer to the detailed channel description.
5. Set the working parameters of the light
Enter the page shown in Figure 1-5 to adjust the on-site parameters of the light
to facilitate on-site installation of the light:
Advanced mode
Pan Invert
Set the Pan rotation direction
OFF Not reversed
ON Reversed
Tilt Invert
Set the Tilt rotation direction
OFF Not reversed
ON Reversed
P/T Rectify
Set whether the luminaire detects P/T out of step and corrects
OFF
Uncorrected position after out of step
ON Automatically correct position after out of step and
record out of step failure
Pan offset Set the position of the X-axis zero point of the fixture
4-150
4-150
Tilt offset Set the position of the zero point of the yoke of the light
4-48 4-48
Data Hold
Set the output status of the light when there is no DMX signal
OFF No signal, so the motor and light source return to the
position and state when the reset is completed
ON No signal, keep the last frame of DMX data output
10
Lamp when
Set the way the lamp is turned on for the first time after powering up
Power on Turn on the lamp first when powering up, reset the
light after 30 seconds
RstDone
Reset the light after 3 seconds of power-on, turn on
the lamp after resetting
Manual After the reset is complete, manually turn on the light
lamp through the menu or console
Factory
settings
A confirmation box pops up, and after selecting "SURE", the light
parameters are returned to the factory settings.
When the power-on lamp opening mode is selected, after the lamp is powered on, it
will wait for 30 seconds for the lamp to fully start. After the internal voltage is stable
enough, the reset program will be started. If the field power capacity is stable, it is
recommended to turn on the light lamp mode.
When the light cannot correct the position, first check if the "optocoupler correction" is
turned off.
When the signal is removed, if the position of the light is not as intended, first check
the “Data Hold” setting.
When setting the XY offset, after completing the setting, first control the XY with the
maximum stroke to check that the X Y does not hit the positioning lever or the
housing.
6. Check the current status of the fixture
Enter the page shown in Figure 1-6 to view the information and real-time status
of the light to know the status of the light. If the light needs to be sold, please
provide the status information displayed on the page for judgment. The details
are as follows:
Status information
Motor
information
Display information status of all motors and signals in the light
Hall
Not displayed, indicating that the motor has no
Hall correction, 0 means the motor leaves the
calibration position, and 1 means the motor is in
the correction position.
Status Display motor reset completion status
Pan
Display real-time position values of Pan
Tilt
Display real-time position values of Tilt
Optocoupler
Display the level status of two signals of Pan and
Tilt optocouplers, binary
11

BEAM SPOT WASH (3IN1) 380W BEAM SPOT WASH (3IN1) 380W
Error
Logging
Display the last 8 fault records of the light reset and operation. The fault
record is not saved after power off, and the power-on cycle is valid.
Fault data
Total number of faults detected after power-on
12:03
Power-on time when the fault occurred, in minutes
Hall failure
The motor does not detect a valid Hall signal when
the motor is reset.
Hall short
circuit
The Hall signal detected when the motor is reset is
always valid.
Optocoupler
failure
No valid optocoupler signal detected for motor
reset
Out of step Corresponding motor out of step during operation
Bat
Corresponding to the positioning rod when the
motor is reset
Lamp failure
lamp accidental defoaming
Sensor failure
Temperature sensor signal is abnormal
Fan failure The main fan is not working properly.
Light
Status
Display key status data of the current fixture for reference
Communication
0~100%, communication quality of the internal
data link of the light
Error count
The number of error frames detected after
power-on, cumulative
Light source
temperature
Display the temperature of the current light source,
"---" means no detection
Display panel
temperature
Display the temperature of the current display
panel or the ambient temperature in the vicinity
Sensor
temperature
Displays the ambient temperature of the current
motherboard temperature or motherboard
installation location
Version
information
Display the information and version of the current luminaire, an
important reference for after-sales maintenance
device
The name of the light, the same as the device
information of the RDM
model
The model of light ,the same as the model
information of RDM
Display board
Display board firmware version and serial number
main board 1
Main board 1 firmware version and serial number
Light time
Record the total accumulated time of the light source on, in minutes,
the user manually removes it, as the time reference for regular
maintenance of the light source
Total time
Record the total accumulated time of the lamp on, in minutes, not
clear
12
Maintenance
To prolong the life of the projector, some maintenance work has to be done to
ensure the optical system in good condition. If the projector does not function, check
the fuses on the power socket of the projector, they should only be replaced by
fuses of the same specification. Should these be damaged, call a qualified
technician before replacement. The projector has thermal protection device that will
switch off the projector in case of overheating. Should either of these operate, check
that the fans are not blocked, and if they are dirty, clean them before switching on
the projector again. Check that the fans are operational, if not, call a qualified
technician.
☆
Any maintenance work should only be carried out by qualified technicians.
Keeping The Product Clean
To ensure the reliability of the projector, it should be kept clean. It is recommended
that the fans should be cleaned every 15 days. The lens and dichroic colour filters
should also be regularly cleaned to maintain an optimum light output.
Do NOT use any type of solvent on dichroic colour filters.
Cleaning frequency depends on the environment in which the fixture operates: damp,
smoke or particularly dirty surroundings can cause greater accumulation of dirt on the
unit's optics. A soft cloth and typical glass cleaning products should be used for
cleaning. It is recommended to clean the external optics at least once every 15 days
and clean the internal optics at least once every 60 / 90 days.
☆
Do not use any organic solvent, e.g. alcohol, to clean housing of the
apparatus.
Equipment and Appendix:
☆Beam Spot Wash 380W Moving Head Light 1pcs
☆Power Cable 1pcs
☆XLR connector 1unit
☆Light Hook 2pcs
☆The Product of Instruction 1pcs
13

BEAM SPOT WASH (3IN1) 380W BEAM SPOT WASH (3IN1) 380W
Trouble Shooting:
Problem Answer
The moving head light doesn’t
switch on.
Check the fuse the power socket
Replace the lamp
Although shines, but the moving
head lamp doesn’t accept the
instruction of the controller.
Check the digital start address and also check
the connection situation of the communication
control line
The moving head lamp only can
work intermittently.
Inspect the power supply and voltage is whether
normal.
Make sure the fan is working well or fans and
their filters not blocked
Defective projection Make sure the lamp is within its life limit
Remove dust or grease from the lenses.
The beam appears dim heck the optics is clean or the lens in good
condition(not cracked)
Replace with a new lamp of the specified type
and rating.
☆
Other maintain work should by the specialist which has the experience to
carry on.
Channel List:
(24CH) (20CH) DMX Value Function
1 1 0－255 Pan(0-540°)
2
2
0
－
255
Pan Fine(0-2°)
3 3 0－255 Tilt(0-270°)
4 4 0－255 Tilt Fine(0-1°)
5 5 0－255 P/T Speed from fast to slow
6 6 0－255 0-100% dimmer
14
7 7
Shutter
0-3
Closed
1-103
Pulse strobe from slow to fast
104-107
Open
108-207
Gradual strobe from slow to fast
208-212
Open
213-251
Random strobe from slow to fast
252-255
Open
192-223
Random Slow - Fast
8 8
Colour
0-5 White
6-10 White+ Colour 1
11-15 Colour 1 (Red)
16-20 Colour 1+Colour 2
21-26 Colour 2 (Dark green)
27-31 Colour 2+Colour 3
32-37 Colour 3 (brownish yellow)
38-42 Colour 3+Colour 4
43-47 Colour 4 (Dark blue)
48-52 Colour 4+Colour 5
53-58 Colour 5 (Pink)
59-63 Colour 5+ Colour 6
64-68 Colour 6 (Orange)
69-74 Colour 6+ Colour7
75-79 Colour7 (Blue-green)
80-84 Colour7+ Colour8
85-89 Colour8 (Orange red)
90-94 Colour8+ Colour9
95-100 Colour9 (Cool colour)
101-105 Colour9+ Colour10
106-111 Colour10 (Purplish red)
112-116 Colour10+ Colour11
117-121 Colour11 (Fluorescence)
122-127 Colour11+White
128-191 Fast Rotation - Slow Rotation
192-255 Slow Rotation - Fast Rotation
15

BEAM SPOT WASH (3IN1) 380W BEAM SPOT WASH (3IN1) 380W
9 9
Fix Gobo
0-9
White
10-14
Gobo 1
15-19 Gobo 2
20-24
Gobo 3
25-29
Gobo 4
30-34 Gobo 5
35-39
Gobo 6
40-44
Gobo 7
45-49 Gobo 8
50-54
Gobo 9
55-59
Gobo 10
60-64
Gobo 11
65-69 Gobo 12
70-74
Gobo 13
75-79 Gobo 1 Shake from slow to fast
80-84 Gobo 2 Shake from slow to fast
85-89
Gobo 3 Shake from slow to fast
90-94
Gobo 4 Shake from slow to fast
95-99 Gobo 5 Shake from slow to fast
100-104
Gobo 6 Shake from slow to fast
105-109
Gobo 7 Shake from slow to fast
110-114
Gobo 8 Shake from slow to fast
115-119 Gobo 9 Shake from slow to fast
120-124
Gobo 10 Shake from slow to fast
125-129 Gobo 11 Shake from slow to fast
120-134 Gobo 12 Shake from slow to fast
135-139
Gobo 13 Shake from slow to fast
140-195
Fast Rotation - Slow Rotation
196-199 Stop
200-255
Slow Rotation - Fast Rotation
10 10
Effect Gobo
0-14 White
15-29 Gobo 1
30-44
Gobo 2
16
45-59 Gobo 3
60-74 Gobo 4
75-89 Gobo 1 Shake from slow to fast
90-104 Gobo 2 Shake from slow to fast
104-114 Gobo 3 Shake from slow to fast
115-127 Gobo 4 Shake from slow to fast
128-255 Gobo running from slow to fast
11 11
Rot Gobo
0-9 Small White
10-19 Gobo 1
20-29 Gobo 2
30-39 Gobo 3
40-49
Gobo 4
50-59
Gobo 5
60-69
Gobo 6
70-79
Gobo 7
80-89 Gobo 1 Shake from slow to fast
90-99
Gobo 2 Shake from slow to fast
100-109 Gobo 3 Shake from slow to fast
110-119 Gobo 4 Shake from slow to fast
120-129 Gobo 5 Shake from slow to fast
130-139 Gobo 6 Shake from slow to fast
140-149 Gobo 7 Shake from slow to fast
150-199 Fast Rotation - Slow Rotation
200-255 Slow Rotation - Fast Rotation
12 12
Gobo Rot
0-127 Rotation (0-360°)
128-187 Fast Rotation - Slow Rotation
188-195 Stop
196-255 Slow Rotation - Fast Rotation
13 13 Prism-1 0-127 Empty
128-255
Prism-1(Round 24)
17

BEAM SPOT WASH (3IN1) 380W BEAM SPOT WASH (3IN1) 380W
14 14
Prism-1 Rot
0-127 Rotation (0-360°)
128-187
Fast Rotation - Slow Rotation
188-195
Stop
196-255
Slow Rotation - Fast Rotation
15 15 Prism-2
0-127
Empty
128-255
Prism-2(Linear 6)
16 16
Prism-2 Rot
0-127 Rotation (0-360°)
128-187
Fast Rotation - Slow Rotation
188-195
Stop
196-255
Slow Rotation - Fast Rotation
17 17
Zoom
0-255
Linear Zoom
18 18
Focus
0-255 Linear Focus
19 19
Auto Zoom
0-31
No function
32-127
Auto Zoom at 5m
128-191 Auto Zoom at 7.5m
192-255
Auto Zoom at 10m
20 20
Control
100-105 Lamp OFF after 3 second
200-205 Lamp ON after 3 second
210-215
Pan/Tilt reset
220-235
Effect motor reset
240-255
All motor reset
21 *
Dimmer fine
0-255
Dimmer fine
22 *
Gobo fine
0-255
Gobo fine
23 *
Zoom Fine
0-255
Zoom Fine
24 *
Focus Fine
0-255
Focus Fine
18
Technical Parameters:
Voltage : AC100~240V/50-60Hz
Power consumption:580W@ (220V)
Lamp: YODN MSD 380 R18 lamp
Color temperature : 7800K
Color: 11 Color + White, Color half step function
Gobo1: 13 Fixed gobo + White, Gobo shake function
Gobo2: 7 Rotating gobo + White, Gobo shake function
Gobo3: 4 Effect gobo + White, Gobo shake function
Prism:1Pcs rotation 24-face prism, Bilateral rotation, Prism superposition
function
1Pcs rotation 6-facet linear prism, Bilateral rotation, Prism superposition
function
Dimmer : 0-100% linear adjustment ,Strobe(0.5-9 times/ second)
Focus : Electric focus from near to far
ZOOM: Linear ZOOM function
Zoom angle : 2.5°-5° beam model; 5°–60° spot model
Channel :20/24CHs
Control mode : DMX512, Automatic and Master/ slave mode, Sound
Pan: X axis 540°automatically accurate positioning
Tilt: Y axis 270°automatically accurate positioning
Control Panel: Touch LCD display panel with 4
buttons,2.2-inch color LCD display with
English and Chinese menu, can be rotation 180 °
Protection grade:IP20
Gross Weight: 25.5 kg
Package Size: 550 x 480x 630mm
19