MJ LED LIGHTNING MJ-2010A-4IN1 User manual

LED OUTDOOR PAR-1810
MJ-2010A-4IN1
User Manual
=======PROFESSIONAL LED LIGHTING ========
Thank you for choosing our outdoor LED Par light. For the sake of your safety,
Please read and follow these instructions carefully and keep this manual in a safe
place for future reference
WARNING
Please do not use the lamp under the water!
Please do not connect the power cable hand by hand
over 10 lights per time!
Important notice:
Before open the LED outdoor par light and if you want to do the
repair work, please make sure the power source is at the separation
condition.

Unceasingly carries on the product improvement about our
company the policy, in this instruction booklet carries the data will
have the possibility to be able to change in the future, when no
longer separate notice change matters concerned. Our company
retains when the product improvement changes the related
specification the authority. This instruction booklet publisher cannot
be responsible regarding this instruction booklet in information
accuracy, also cannot the related consequence which causes
regarding these information be responsible.

V. Channel List:
4CH Mode
Channel
Value
Function
CH1 0-255 Red dimming from dark to bright
CH2 0-255 Green dimming from dark to bright
CH3 0-255 Blue dimming from dark to bright
CH4 0-255 White dimming from dark to bright
8CH Mode
Channel
Value
Function
CH1 0-255 Main dimming from dark to bright
CH2 0-255 Control strobe from slowly to quickly
CH3
0-50 No function
51-100 Color change by jumping
101-150 Color change by fade
151-200 Color change by pulse
201-255 Sound control
CH4 0-255 The speed of function from slowly to quickly
CH5
0-255
Red dimming from dark to bright
CH6
0-255
Green dimming from dark to bright
CH7
0-255
Blue dimming from dark to bright
CH8
0-255
White dimming from dark to bright
5

III. Technical Parameters:
Construction: Aluminum
Voltage: AC100-240V, 50Hz/60Hz
LED: 18PCS 10W 4IN1 LED
Power Consumption: 180 Watts
LED Current: 500mA / 1 pc
LED Beam Angle: 25°(±5) degree
LED Lifetime: 80,000-100,000 hours
Color: RGBW color mixing
DMX Control: 4/8 Channels
Operation Modes: DMX512, Auto, Master-slave, Sound
Control Panel: Digital 4 Character Alphanumeric
Maximum Ambient Temperature: 60° C
Waterproof Rating: IP65
Gross Weight: 10.2kg
Package Size: 31×31×35.5CM
IV. Waterproof manage:
Signal joint(at most 30pcs)XL-
3R,at first, use the high voltage and
waterproof adhesive tape with mucosity to enlace the joint one circle. After
stretch the adhesive tape, then you can enlace it, please reference the
operation describe.), then cover a 20mm cannula with pyrocondensation.
At last, envelop the joint to reach a waterproof effect.
Warning
If this joint can’t do the waterproof manage, then the lamp waterproof effect
will be invalid, then destroy the product.
4
I. Installation:
Thank you for having chosen our LED lighting
Unpack the device ,inside the box you should find:
1) Light----------------------------------------------1pcs
2) Power Cable-----------------------------------1pcs
3) User Manual-----------------------------------1pcs
Features
. 4,/8 DMX channels selectable for numerous applications
. DMX-controlled operation, Sound-controlled operation or stand alone
operation with Master/Slave-function
.Operation very easy ，human design ，dimming no flicker 、jitter
phenomena. Can be adapted to video, photography, television and other
demanding lighting occasions.
II. Modes of Operation
There are four modes of operation: DMX control (Slave), Sound,
Automatic, and Manual. In the Sound, Automatic, and Manual settings,
the unit will perform independently and will send DMX signal, so that
other fixtures may be linked. This is useful if you want every fixture
doing the same thing and do not wish to use an external DMX controller.
All menu settings will be retained even after the lights have been
powered off.
1. DMX Control – Fixture is remotely controlled via a DMX controller
(sold separately).
2. Sound Control – Fixture changes color in response to noise.
3. Manual Control – Color are manually set via the control pad.
4. Automatic Color Cycle – Unit cycles through colors automaticall
y.
User sets whether fade is instant or slow, and the length of time
between fades.
1

No.
Display
Function
1 A001 A001—A512 (8 channel) press “UP” and “Down” button
change the DMX address
2 d001 d001—d512 (4 channel) press “UP” and “Down” button
change the DMX address
3 CC50 CC01—CC99 (Color change by Snapping), press “UP” and
“Down” button change the snapping speed
4 CP00 CP01—CP
99 (Color change by Fade), press “UP” and
“Down” button change the Fade speed
5 DE50 DE01—DE99 (Color change by pulse
), press “UP” and
“Down” button change the Fade speed
6 BEBE Color change by Sound
7 R220 R000—R255 (R dimming by hand)
, Press ENTER to
chose the RGBW to balance
8 G220 G000—G255 (G dimming by hand)
, Press ENTER to
chose the RGBW to balance
9 B220 B000—B255 (B dimming by hand)
, Press ENTER to
chose the RGBW to balance
10 W220 W000—W255 (W dimming by hand), Press ENTER to
chose the RGBW to balance
NOTE：When operating the color balance function, please press ENTER
to choose the colors, then use UP or DOWN to select the brightness.
1. DMX Control
1. If you wish to control the unit remotely via DMX, you will need
a DMX controller. Connect an XLR cable to the controller's
DMX output and the fixture's input.
2
2. Set the fixture to receive DMX signal
a) Press and hold 'MENU' button until display says A001 or
d001.
(Note:A001 is 8CH,d001 is 4CH,you can choose it.)
b) Press 'ENTER', then the fixture will receive the DMX 512
signal.
c) Press UP or DOWN to select the desired address.
d) Press ENTER button to activate the selection..
2. Sound Activation (color changes in response to loud noises)
1. Press and hold 'MENU' button until the display panel says BEBE
(short for sound).
2. Press 'ENTER'
3. Manual Control(RGBWAP dimming by hand):
1. Press and hold 'MENU' button until display panel says
R220 ,G200 ,B220,W220
2. Press UP or DOWN to select the brightness
3. Press 'ENTER'
RED (0-255) GREEN (0-255)
BLUE (0-255) WHITE(0-255)
4. Automatic Color Cycle
1．Press MENU, the display panel says CC01 – CC99,this way is color
jumping and speed changing.
2. Press MENU, the display panel says CP01 – CP99,this way is color
changes by Fading.
3. Press MENU, the display panel says DE01 –DE99,this way is color
changes by pulse.
3