Mobeye i110 User manual

User manual
Mobeye®i110
SW version 3.N

2
Table of content
1. How to Use the Mobeye 5
1.1 To get ready in three steps 5
1.2 Step 1: SIM Card 5
1.3 Step 2: Place the batteries 5
1.4 Step 3: Program the phone numbers 6
1.5 Switching the motion detector on/off 6
1.5.1 Switching on 6
1.5.2 Switching off 6
1.6 Test GSM network strength 6
1.7 Sensor test 7
1.8 Mobeye®settings 7
1.8.1 Possible settings 8
1.8.2 Receive the settings in an SMS 10
1.9 Configuration 11
2. Issue solving 14
3. Technical data 15

3
Attention! Very important
This user manual contains important guidelines for the installation and usage of the
Mobeye®i110. Please read these thoroughly before you start using the Mobeye®!
In case of damage caused by disregarding the guidelines, the warranty expires.
The user must regularly check the proper functioning of the Mobeye®. The
manufacturer cannot be held liable for any damage caused by any incorrect use or
incorrect functioning of the Mobeye®.
Safety guidelines
• The permitted ambient temperature during operation may not be exceeded (not
lower than -10°C and not higher than 55°C).
• The device is intended for use in dry and clean places.
• Protect the device from moisture, heat and water splashing.
• The guidelines for the battery usage must be regarded.
• Do not expose the device to strong vibrations.
• Do not let it fall from height.
• Do not use in an environment where any inflammable gases, vapours or dust are
present or could be present.
• Reparation of the device may only be carried out by people, trained for Mobeye®
repair.
• In case the device must be repaired, only original replacement components may be
used. The use of different parts may lead to damage of the Mobeye®.
Use in accordance with the regulation
The use of this device in accordance with the regulation is the generation of SMS
text messages and telephone calls after detection of a motion by the motion detector
or of a temperature that outreaches the programmed limits.
Other usages are not permitted.

4
Introduction
The Mobeye®is an easy to install alarm system that will
notify you in case of a detection using the built-in GSM.
To use the Mobeye®you will need a SIM-card of any
provider.
Typical applications are the security of places without any
power supply or the temporary security of objects.
The Mobeye®has the following features.
Alarm notifications after movement detection
In case of the detection of an intruder, the Mobeye®will send an SMS text message
to your phone(s). The Mobeye®will also call the phone numbers in order to be sure
the message is not missed. It is also possible to let the siren sound. After an alarm
the Mobeye will be in standby status for about 5 minutes. Hereafter it is able to report
new movements.
Alarm notifications after detection out of range temperature
It is possible to program a minimum and/or maximum temperature. The Mobeye will
monitor the actual temperature and sends an alert as soon as the temperature
reaches the limit.
Low battery message
The Mobeye®will send an SMS text message in case the batteries must be replaced.
After this, you need to change the batteries as soon as possible. For some time the
Mobeye®remains functioning as normal. Even when the Mobeye®is unset, it will
measure the battery strength and send the message.

5
1. HOW TO USE THE MOBEYE
1.1 TO GET READY IN THREE STEPS
To get started with the Mobeye® only three steps are needed.
1. Place the SIM card in the Mobeye®.
Make sure this SIM card is not secured by a PIN code.
2. Place the four batteries.
3. Enter at least one phone number in the Mobeye®.
1.2 STEP 1: SIM CARD
To use the Mobeye®a SIM card of any provider is needed. On this SIM card, the PIN
code security needs to be disabled. If you have a SIM card with PIN code, you can
disable this using any mobile phone and switch off the PIN code security. Please
consult the manual of the used mobile phone for the procedure.
The SIM card needs to be placed before the batteries. When using a prepaid SIM
card, take care of the remaining value. Apart from that it is wise to set a recurrent
test message in the menu so the card will be used at least once a month.
Open the Mobeye®
Place the SIM card
Place the batteries
Close the Mobeye®
1.3 STEP 2: PLACE THE BATTERIES
Place the four lithium 3,0 volt batteries (CR123). When replacing the batteries, all
settings remain unchanged.
After placing the SIM card and the batteries, the Mobeye® will perform a self test
during 1 minute. During the test, the light is red.
In case the light is flashing red, a problem with the SIM card is detected. A reason
could be no SIM card was placed, or the PIN code security of the SIM card was not
disabled.
S
I
M

6
1.4 STEP 3: PROGRAM THE PHONE NUMBERS
You need to program at least one phone number in the unit. This phone number is
used to send the messages to.
Enter your 4 digit user code (factory setting: “1111”)
Press “menu”
Enter “01” (01 for the 1st phone number, 02 for the 2nd phone number)
Press “OK”
Enter the phone number (e.g. 0612345678)
Press “OK”
The light turns green and a confirmation melody is played.
The Mobeye® is ready to use.
1.5 SWITCHING THE MOTION DETECTOR ON/OFF
1.5.1 Switching on
To activate the Mobeye®motion detector with your personal user code.
Enter your user code
Press “OK”
The light turns red shortly and an indication tone is started. This repetitive tone will
last during the exit delay of 30 seconds. As soon as the acoustic signal stops, the
Mobeye®is active.
In case the user code is entered incorrectly 3 times, the indicator turns red and the
Mobeye® will be blocked during 10 minutes.
1.5.2 Switching off
To de-activate the Mobeye®motion detector with your personal user code.
Enter your user code
Press “OK”
The light switches to green and a confirmation melody is played.
1.6 TEST GSM NETWORK STRENGTH
Before using the Mobeye®is it advised to test the GSM reach at the place where the
device is to be placed.
Enter your user code
Press “menu”
Press “12”
Press “OK”

7
First the light turns red. The Mobeye®now switches on the GSM modules and
searches for all present networks. It also checks the network strength of the SIM
card provider in the device.
As soon a the GSM network is found, the light will turn green.
The GSM reach of the used SIM card can be read from the LED indicator:
LED
Description
Green during 30 seconds
Reach is good
Flashing green
Reach is bad
Red
No reach
Flashing red
No valid SIM card or Sim card is not pin code
free
Besides, the telephone number at memory place 01 will receive an SMS text
message, containing all existing GSM networks, sorted by provider. It also tells the
strength per network.
This search function can take some minutes. In case you want to leave the function
before it is ready, please press “OK” twice.
Warning
In case of a weak signal, the Mobeye® can still be used, but there is a risk that
message cannot be sent or will be received with a delay. In case of no reach, it is
advised to use a SIM card of a provider with a stronger network.
1.7 SENSOR TEST
In order to check the reach of the sensor, a sensor test can be executed.
Enter your user code
Press “menu”
Press “11”
Press “OK”
A confirmation beep is heard. First the green light will be flashing. After about 30
seconds the light will be on continuously. In this mode the sensor test can be done;
each time the sensor detects a movement, a repeating beep will sound.
Leave the test by entering OK twice.
1.8 MOBEYE®SETTINGS
The Mobeye®settings can be added via the keypad and SMS text messages. First
the possible settings are discussed, later the way of programming.

8
1.8.1 Possible settings
1.8.1.1 Change the user code
The user code is the code for switching on/off the active status. In the active status
the Mobeye®will detect movements. The user code is also needed to program the
settings or activate the special functions. It is possible to change the user code to
any 4-digit number.
In case the user code is entered incorrectly 3 times, the indicator turns red and the
Mobeye® will be blocked during 10 minutes.
1.8.1.2 Change telephone numbers
The SMS alarm message and voice („alarm signal‟) message can be sent to one or
two telephone number. At least one telephone number must be entered in the
Mobeye®. The test messages and low battery messages are sent to the first
programmed telephone number.
1.8.1.3 Sensor sensitivity
The detectors‟ sensitivity can be changed to a high or low(er) value.
1= High
2 = Low
In the high sensitivity mode each detection will provoke an alarm. In the lower
sensitivity mode the alarm will be provoked in case two detections are measured
within a time frame of 15 seconds. This mode prevents false alarms in case of e.g.
draught and is most suitable in case the sensor is directed towards an open space.
1.8.1.4 Entry delay
It is possible to choose from 4 entry delay times. The entry delay is the time between
the moment of detection and the moment of sending the first SMS text message.
Take care: in case the GSM network has a low reach, the time can be longer in case
the network connection was not established within the time of the entry delay.
1.8.1.5 Entry indication
It is possible to hear an indication beep during the entry delay. This can be used as a
reminder that the Mobeye is in active mode.
1.8.1.6 Siren
After the entry delay, the siren can sound during two minutes. At the same time the
SMS text messages and telephone calls will be done. At soon as the Mobeye is
switched off, the siren will stop.

9
It is possible to test the loud alarm. During the test the siren will be heard until it is
cancelled by <OK> <OK>. This test is also possible in case the Mobeye i110 is
programmed as a silent alarm.
1.8.1.7 Temperature alarm
The Mobeye®is able to send a temperature alarm as soon as the actual temperature
reaches a programmed min. or max. level. This function can be used independently
of the motion detection. As soon as the temperature is too high or too low, an SMS
text message is sent, followed by a telephone call. As long as the out of range
temperature remains, the report will be repeated hourly. Once the temperature is
back to normal, the Mobeye®confirms this to you.
This function is active as soon as a temperature limit is programmed. By resetting
the limits, the function becomes inactive.
1.8.1.8 Adjusting the temperature
The built-in temperature sensor may have a standard deviation of the actual
temperature. In this case, the deviation will be similar at all temperatures. It is
possible to correct the temperature deviation in the Mobeye i110. In the SMS setting
summary, you see the reported temperature. If a correction is specified, it is
processed in the displayed temperature; the correction factor itself is displayed
separately.
Example: Mobeye temperature: 13 C. Actual temperature: 14 C. To correct this
deviation, one degree should be added.
1.8.1.9 Interval test message
The Mobeye®can send test messages. Through these test reports you will be
ascertained of the proper functioning of your Mobeye. You can set the interval
between the reports indicate the number of days between reports. This is adjustable
between 0 (no test reported) and 30 (monthly test message). Note: the interval of 1
day will result in a daily test message, the exact time between the message will be
about 24 hours.
The smaller the interval between the test reports, the shorter the battery life.
1.8.1.10 SMS Recognition text
It is possible to send an extra text in the SMS text messages, in order to recognize
from which Mobeye® the message has been sent. The first part of the SMS text
message will always contain standard text like „Mobeye alarm‟, or „Test message
OK‟. The recognition text will be written after the standard text.
This text (max. 20 characters) can be programmed by sending an SMS to the
Mobeye® .

10
1.8.1.11 Alarm monitoring center
For some countries the Mobeye has been prepared to send the alarm and test
message to an alarm monitoring center instead of to private telephone numbers.
Please check the website or contact www.mobeye.eu to inquire for the actual status
in your country.
1.8.2 Receive the settings in an SMS
It is possible to send the programmed settings to your GSM.
Enter your user code
Press “menu”
Press “10”
Press “OK”
In about 30 seconds the telephone programmed at memory place 01 will receive the
settings in an SMS text message.
1.8.2.1 Reset to factory settings
After entering your personal code –menu –99 –OK the Mobeye is back to factory
settings. You personal code will be 1111 again.