Mocka Tahoe User manual

mocka.co.nz I mocka.com.au
ASSEMBLY INSTRUCTION S
Tahoe Change Table
• READ all instructions before use of the change
table.
• FALL HAZARD: children have suered serious
injuries after falling from changing tables. Falls can
happen quickly.
• STAY in arm’s reach of your child and NEVER
leave a baby unattended on any change surface.
• ALWAYS keep one hand on the baby when using
the change table to prevent the baby from falling.
• DO NOT use if the product is damaged or broken.
• NEVER allow baby to sleep on the change table.
This item is NOT a safe sleeping surface.
• REMOVE all hazards from the change table area
out of reach of your baby (E.G pins, lotions, toys).
• SUITABLE FOR: newborn to 12 months. Maximum
to 11 kgs.
• READ and follow the manufacturer’s instructions
and KEEP for future use.
• USE a changing pad that is 78cm x 46cm x 10cm.
• WARNING this product is not intended to be used
without a changing pad. use of this product without a
changing pad may result in death or serious injury to
your child from falling.
• WARNING to help avoid any serious or fatal injury,
this product comes included with a wall strap to pre-
vent topping. we strongly recommend that this prod-
uct be permanently fixed to a wall or other suitable
surface by a qualified tradesperson.
• CLEANING & CARE
DO NOT use the product unless all components are
correctly fitted and adjusted. regularly inspect the
change table for maintenance of loose screws etc.
DO NOT use the change table if any part is broken,
torn or missing. contact the manufacturer for further
advice.
WIPE the change table clean using a clean damp cloth
and suitable commercial cleaner.
• ENSURE the changing table is level, stable and struc-
turally sound.
manufactured by: mocka products pty ltd. po box 18,
pinkenba, qld 4008. mocka limited, po box 29335, ric-
carton, christchurch 8440, nz
!! WARNING

mocka.co.nz I mocka.com.au
ASSEMBLY INSTRUCTION S
Tahoe Change Table
HARDWARE SUPPLIED
WALL STRAP
60x
locking nut
B
16x
small screw
E
G
L+R slide rail
4x
H
L+R slide rail
4x
cover
20x
4x
long screw
14x
long screw
CD
60x
bolt
A
F
1x
screw
1x
wall screw
2x
washer
1x
wall anchor
1x
safety strap
Z
X
W
J Y
*We recommend using a Flathead screwdriver to tighten
all locking nuts 100% before first use. Please clear any
loose wood from the locking nut holes before inserting
the nut to ensure it locks 100%.
Phillips & Flathead screwdrivers and hammer required
For quicker assembly, we recommend theuse of a power drill on a
low-speed setting.
2
40

mocka.co.nz I mocka.com.au
ASSEMBLY INSTRUCTION S
Tahoe Change Table
1 2
Insert 8x bolts (A) into panels [5]. Tighten with a screwdriver. Insert 4x locking nuts (B) into panel [1] and connect
2x panels [5] to panel [1] , tighten with a screwdriver.
Insert 4x bolts (A) into panel [1], tighten with a screwdriver.
Cover locking nut with 4x covers (F).
A
A
A
A
A
A
A
A
AB
B
B
B
B
F
F
F
F
1
5
A
A
A
A5
5
5

mocka.co.nz I mocka.com.au
ASSEMBLY INSTRUCTION S
Tahoe Change Table
3 4
Insert 8x bolts (A) into 2x panels [6]. Tighten with a screwdriver.
Connect panel [6] and panel [9] with 8x locking nuts (B).
Cover locking nut by 8x covers (F)
Insert 6x long screws (D) into panel [1] and [6] and [9].
Tighten with a screwdriver.
B
B
B
DDDD
D
D
F
F
F
F
1
6
9
9
9
6
6
B
A
A
A
A

mocka.co.nz I mocka.com.au
ASSEMBLY INSTRUCTION S
Tahoe Change Table
5 6
Insert 8x bolts (A) into panel [3] and [4]. Tighten with a screwdriver.
Attach 1x left slide rail (G) to panel [3] and secure with 2x small
screws (E). Attach 1x right slide rail (G) to panel [4] and secure with
2x small screws (E).
Connect panel [3] and panel [4] together with panel [11]
and panel [12], secure with 8x locking nuts (B).
Tighten with a screwdriver.
A
AAA
A
AA
A
E
EE
E
GG
34
GG
B
B
B
B
B
B
B
B3
4
11
12

mocka.co.nz I mocka.com.au
ASSEMBLY INSTRUCTION S
Tahoe Change Table
7 8
Insert 6x bolts (A) into panel [2]. Tighten with a screwdriver. Connect panel [2] together with panel [3] and panel [4]
and panel [13], secure with 6x locking nuts (B), tighten
with a screwdriver. Attach 1x safety strap (W) to panel [13]
with 1x screw (Y) and 1x washer (Z).
Tighten with a screwdriver.
A
A
A
A
A
A
A
2
B
2
3
11
Y
Z
W
13
4B
B
B
B
B

mocka.co.nz I mocka.com.au
ASSEMBLY INSTRUCTION S
Tahoe Change Table
9 10
Insert 4x long bolts (C) into 2x panels [7] and connect
with 2x panels [8]. Tighten with a screwdriver.
Connect panels [8] to bottom panel [2] and secure
with 8x screws (D). Tighten with a screwdriver.
C
C
C
C
7
8
8
7
7
D
D
D
D
D
D
D
D
2
3
4
8
8

mocka.co.nz I mocka.com.au
ASSEMBLY INSTRUCTION S
Tahoe Change Table
11 12
Insert 2x bolts (A) into panel [11]. Tighten with a screwdriver.
Connect 1x panel [10], secure with 2x locking nuts (B), cover
locking nut with 2x covers (F). Attach 1x left slide rail (G) to
panel [3] and secure with 2x small screws (E). Attach 1x right
slide rail (G) to panel [4] and secure with 2x small screws (E).
Slide panel [14] and [15] between the grooves on panels [3]
and [4] and [13] to form the back of the unit as shown.
B
B
3
3
4
4
11
14
13
13
15
G
G
10
A
A
E
E
E
E
FF

mocka.co.nz I mocka.com.au
ASSEMBLY INSTRUCTION S
Tahoe Change Table
13 14
Connect table top unit to panel [3] and [4] and [10] and [13],
secure with 8x locking nuts (B). Cover locking nuts by 6x covers (F).
Insert 6x bolts (A) into panel [16]. Tighten with a screwdriver.
Connect panel [17] & [18] to panel [16], secure with 4x locking
nuts. Tighten with a screwdriver.
Connect 2x panels [19] to panel [16], secure with 2x locking
nuts (B). Tighten with a screwdriver.
Insert panel [20] between the grooves on panel [17] and [18].
F
F
F
F
F
F
3
4
10
18
17
17
18
19
19
20
16
16
Drawer x 2
1
13
B
B
B
B
B
B
B
B
B
B
B
B
B
B
A
A
A
A
A
A

mocka.co.nz I mocka.com.au
ASSEMBLY INSTRUCTION S
Tahoe Change Table
15 16
Insert 6x bolts (A) into panel [21]. Tighten with a screwdriver.
Attach panel [21] to panels [17] and [18] and [19], secure with
6x locking nuts(B). Tighten with a screwdriver. Attach 2x slide
rails (H) to panels [17] and [18] and secure with 8x small
screws (E). Tighten with a screwdriver.
Move the unit into the desired location up against a wall.
Use a drill to create a small hole lining up with the top of
the 1x safety strap (W). Fasten to the wall using 1x wall
anchor (X), 1x washer (Z) and 1x wall screw (J). Ensure the
unit is balanced and steady before use. You’re done, enjoy!
A
A
A
A
A
A
E
E
E
E
E
E
H
H
H
16
W
ZJ
X
Drawer x 2
21
19
19
17 17
18
18
18
B
B
B
B
B
B