Mocka Soho Wooden Highchair User manual

IMPORTANT!
KEEP FOR FUTURE REFERENCE: Backboard Upper
metal rod
Highchair Leg
Footboard
Seat board
Safety Rail
Safety strap
Support brace
Only use the highchair on a flat, even and horizontal floor.
Do not elevate the highchair on any structure or table.
WARNING: Never leave your child unattended in the highchair. Strict
adult supervision is required at all times.
WARNING: Ensure the safety strap is in use at all times to avoid the
child slipping downwards and causing injury. We recommend the use of
the shoulder and waist harness at all times to avoid injury caused by
falls.
WARNING: Do not use the highchair unless components are correctly
fitted and adjusted.
WARNING: Ensure the highchair is positioned away from objects or
structures that can cause injury. Be aware of the risk of open fire and
other sources of strong heat, such as electric bar fires, gas fires etc, in
the vicinity of the highchair.
WARNING: Ensure both the seat and footrest are clicked into position
and cannot be moved by hand, before placing the child in the highchair.
WARNING: For babies/toddlers under 2 years old, please ensure the
seat is positioned on the 1st or 2nd level from the top ONLY.
Do not tighten all screws until all components have been assembled.
The highchair should not be used until the child can sit up unaided.
Do not use the highchair if any part is broken, torn or missing.
Soho Wooden Highchair
1
mocka.co.nz | mocka.com.au
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.

screwdriver required
The best way to clean your highchair – especially the tray is
with a clean damp cloth, and then wipe completely dry.
We recommend you DON’T use household cleaners as these
Using a damp cloth and wiping dry will ensure longevity of
your highchair.
To alter the seat and footrest heights after assembly, simply
loosen all the screws in the upper and lower backrests and
the metal rods on both sides of the highchair. Once loosened
this will allow the seat and footrest to be pulled out. Insert into
the new positions and then lock in place by re-tightening all
the screws. Ensure both the seat and footrest are locked into
position and cannot be moved by hand, before placing the
child in the highchair
Thank you!
The Mocka Team
x6
B
A
x4
C
E
D
F
x6
x1
x4
x1
screw
long screw
bolt nut
Allen key
footpad
safety strap
GH
leg
extender
small screw
x2
15 mm
x2
Hardware Supplied
Pre-installed Hardware
could lift the varnish and upset the wood finish.
Soho Wooden Highchair
2
mocka.co.nz | mocka.com.au
Assembly Instructions

screwdriver required
The best way to clean your highchair – especially the tray is
with a clean damp cloth, and then wipe completely dry.
We recommend you DON’T use household cleaners as these
Using a damp cloth and wiping dry will ensure longevity of
your highchair.
To alter the seat and footrest heights after assembly, simply
loosen all the screws in the upper and lower backrests and
the metal rods on both sides of the highchair. Once loosened
this will allow the seat and footrest to be pulled out. Insert into
the new positions and then lock in place by re-tightening all
the screws. Ensure both the seat and footrest are locked into
position and cannot be moved by hand, before placing the
child in the highchair
Thank you!
The Mocka Team
x6
B
A
x4
C
E
D
F
x6
x1
x4
x1
screw
long screw
bolt nut
Allen key
footpad
safety strap
GH
leg
extender
small screw
x2
15 mm
x2
Hardware Supplied
Pre-installed Hardware
could lift the varnish and upset the wood finish.
x2
C
A
A
A
A
B
B
C
C
x2
B
Ensure all components slot into the corresponding
grooves on the inside of the legs. Loosely fasten rods
(E) provided. Attach wooden support brace using long
screws (B) and bolt nuts (C) as shown.
1To begin assembly, line up backboards, iron rods, and
support brace between both legs of the highchair.
to the highchair legs using screws (A) and allen key
Soho Wooden Highchair
3
mocka.co.nz | mocka.com.au
Assembly Instructions

23
Slide seat board and foot board into slots in the
highchair legs at appropriate heights as required for
child comfort. For babies we recommend the seat on
the 1st or 2nd level down.
Loosely fasten upper and lower backboards to legs
using long screws (B) and bolt nuts (C). Hold nut using a
screwdriver to ensure it is in the right position for screws
and tighten screws with allen key (E).
x4
x4
B
B
C
BC
CC
CB
B
Note: It is important to ensure that the
foot board is inserted at least three rungs
below the top metal rod.
Soho Wooden Highchair
Assembly Instructions
4
mocka.co.nz | mocka.com.au

Jolt Wardrobe
ASSEMBLY INSTRUCTIONS
5
mocka.co.nz | mocka.com.au
23
Slide seat board and foot board into slots in the
highchair legs at appropriate heights as required for
child comfort. For babies we recommend the seat on
the 1st or 2nd level down.
Loosely fasten upper and lower backboards to legs
using long screws (B) and bolt nuts (C). Hold nut using a
screwdriver to ensure it is in the right position for screws
and tighten screws with allen key (E).
x4
x4
B
B
C
BC
CC
CB
B
Note: It is important to ensure that the
foot board is inserted at least three rungs
below the top metal rod.
45
IMPORTANT - To ensure the highchair is 100% safe for your child
please read this important information. Start by working in a
methodical manner by tightening the bottom left screw, then
tightening the bottom right screw. Continue in this manner,
alternating from left to right, working your way up to the top of the
Highchair. This will ensure the pieces lock into place and have the
correct tension and the highchair is balanced. Attach the padded
cushions to seat and backboard for added comfort. Enjoy!
x1
Thread safety strap through the opening in the seatboard
and over the safety rail. Pull the strap tight and fold the
velcro flaps over onto the strap to secure it in place.
*Please note - the two small velcro side straps on the
safety strap are only for use when the seat is on the top
two seat levels. This is the recommended seat height for
babies/infants.
Soho Wooden Highchair
Assembly Instructions
5
mocka.co.nz | mocka.com.au

67
Attach leg extender (G) at the desired point using a
15mm small screw (H) & screwdriver.All done!
To attach the leg extenders, remove white
plastic footpad (D).
LEG EXTENDERS
D
DG
G
x2
H
Soho Wooden Highchair
Assembly Instructions
6
mocka.co.nz | mocka.com.au

67
Attach leg extender (G) at the desired point using a
15mm small screw (H) & screwdriver.All done!
To attach the leg extenders, remove white
plastic footpad (D).
LEG EXTENDERS
D
DG
G
x2
H
8
9
Connect the rest of the harness to the anchor-straps
by clipping together both buckles as shown. Keep the
harness and middle buckle loose and open for now.
Separate the anchor straps and loop around the high-chair
supports and under the backrest. Tie to high-chair frame
by passing each clip through the loop in the straps.
x2 x2
Highchair Harness
Assembly Instructions
7
mocka.co.nz | mocka.com.au

10 11
shoulders and chest. To take the child out of the chair,
All done! Enjoy!
A. Carefully sit child in the highchair and slip arm through harness.
B. Slip child’s second arm through the harness loop.
C. With the harness sitting over the shoulders, clip the front buckles
together as shown.
B
C
A
Highchair Harness
Assembly Instructions
8
mocka.co.nz | mocka.com.au