modway EEI–2934 User manual

︱ Page 1 of 5
EEI–2934 THREE SEATER
Hardware:
Component:
A Bolt M8x40mm
x 16
Thank you for purchasing the MODWAY THREE SEATER!
Before you start, here are some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the three seater, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
B
Allen Wrench M5 x 1
Customer Service 908-368-1025 www.modwayfurniture.com
1. Chair Back x6
2. Chair Seat x3
3. Left Frame x1
4. Right Frame x1
5. Back Cushion x3
6. Seat Cushion x3
7. Batyline x3
8. Middle Frame x1
3 2
7
8
1
5
6
5
6
6
5
8
2
2
7
7
4
1
1

Customer Service 908-368-1025 www.modwayfurniture.com
STEP 1:
STEP 2:
Please assembled middle seater first including the back side.
Please put left side top and bottom wooden bar trough pre drilled holes one by one.
Insert wooden bar or Chair Back (1) and Chair Seat (2) on Middle Frame (8).
Insert 2 pieces of Bolt (A) into the pre-drilled holes on Chair seat (2) through the top pre-drilled holes on Middle
Frame (8).
Use Allen Wrench (B) to tighten Bolts (A) clockwise until secure.
Repeat the same steps for right section.
Insert the tenon on Chair Back (1) and Chair Seat (2) into the rabbet on Middle Seater.
Page 2 of 5
EEI–2934 THREE SEATER
7
1
2 8
8
7
2
7
2
8
8
1
2
A
B
A
A
A
A
Ax4 Bx1
Hardware & Tool required

Customer Service 908-368-1025 www.modwayfurniture.com
STEP 3:
STEP 4:
Insert Batyline fabric (7) on wooden bar.
Carefully position Left Frame (3) to the assembled Chair Back (1) and Chair Seat (2) as shown.
Insert the tenon on Chair Back (1) and Chair Seat (2) into the rabbet on Left Frame (3).
Page 3 of 5
EEI–2934 THREE SEATER
7
2
2
8
8
7
1
3
7
7
2
2
8
8

Customer Service 908-368-1025 www.modwayfurniture.com
STEP 5:
STEP 6:
Insert 2 pieces of Bolt (A) into the pre-drilled holes on Chair Back (1) through the top pre-drilled holes on Left
Frame (3).
Insert 2 piece of Bolt (A) into the pre-drilled holes on Chair Seat (2) through the top pre-drilled holes on Left
Frame (3).
Use Allen Wrench (B) to tighten Bolts (A) clockwise until secure.
Insert the tenon on Chair Back (1) and Chair Seat (2) into the rabbet on Middle Seater as shown.
Insert Batyline fabric (7) on wooden bar. Carefully position Right Frame (4) to the assembled Chair Back (1) and
Chair Seat (2) as shown.
Insert the tenon on Chair Back (1) and Chair Seat (2) into the rabbet on Right Frame (4).
Ax6 Bx1
Hardware & Tool required
Page 4 of 5
EEI–2934 THREE SEATER
B
A
A
B
A
A
A
A
A
A
2
1
7

Customer Service 908-368-1025 www.modwayfurniture.com
STEP 7:
STEP 8:
Carefully position the assembled chair to the desired location. Put Back Cushion (5) and Seat Cushion (6) into
the assembled chair as shown.
Assembly is complete. Your three seater is ready to be used now!
Page 5 of 5
EEI–2934 THREE SEATER
5
6
5 5
6
6
Carefully position Right Frame (4) to the assembled Chair Back (1) and Chair Seat (2) as shown. Insert the
tenon on Chair Back (1) and Chair Seat (2) into the rabbet on Right Frame (4).
Insert 2 pieces of Bolt (A) into the pre-drilled holes on Chair Back (1) through the top pre-drilled holes on Right
Frame (4).
Insert 2 piece of Bolt (A) into the pre-drilled holes on Chair Seat (2) through the top pre-drilled holes on Right
Frame (4).
Use Allen Wrench (B) to tighten Bolts (A) clockwise until secure.
Ax6 Bx1
Hardware & Tool required
3
4
2
2
2
7
7
7
8
8
A
B
A
A
A
A
A
A