modway Perspective EEI-3301 User manual

EEI-3301 SUNBED
Customer Service 908-368-1025 ︱ www.modwayfurniture.com
P age 1 of 5
Thank you for purchasing the MODWAY SUNBED ！
Before you start, here are some helpful advice:
1. Wesuggest youspend a short timereading through this leaflet and then followthe simple step-
by-step instructions.
2. Owing to the size and weight of thesunbed, we recommend that it is assembled by two adults, on a
carpeted or padded area, in theroom that it isintended for. Approximate assembly time: 20 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or the instruction until you have checked all the
components and hardware and the furniture is fully assembled. Please ensurethat the packaging is
disposed of in a safe and environmentally friendly way.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to
tighten the components from time totime, so please save thetools that have been provided.
6. Please keep all fitting out of reach of children.
Component:
○
1○ 2
○
3
○
3
○
3
1 Cushion x 1 2 Bed Frame x 1 3 Leg x 4
Hardware:
Bolt M6x35mm
x 3
B.
Bolt M6x25mm
x 4
C.
Bolt M6x15mm
x 8
D.
Flat Washer
x 15
E.
Nut
x 3
F.
Allen Wrench
x 1
G.
Wrench
x 1
Hardware:
A. Bolt 1/4x20mm x8
B. 1/4”Washer x8
C. M8 Washer x4
D. Allen Key x1
E. Socket x1
F. Tube Plug x4
G. Screw Bar x4
H. Metal Tube x4
I. Hammer (Not Included)

Customer Service 908-368-1025 ︱ www.modwayfurniture.com
P age 2 of 5
EEI-3301 SUNBED
STEP 1:
Please put the Bed Frame (2) on a carpeted or padded surface, then turn over the Bed Frame (2).
STEP 2:
○2
Insert one end without a nut of the Long Screw Bar (G) through 1 piece of M8 Washer (C)
and 1 piece of Metal Tube (H) into the top hole of the Leg (3) as shown. Repeat the same
steps for the other three Legs (3).
Hardware & Tools required
H
X4
G
X4
C
X4
○
3
○
G
○
C
○
H
Insert one end without a nut of the Long Screw Bar (G) through 1 piece of M8 Washer (C) and 1
piece of Metal Tube (H) into the top hole of the Leg (3) as shown. Repeat the same steps for the
other three Legs (3).

Customer Service 908-368-1025 ︱ www.modwayfurniture.com
P age 3 of 5
EEI-3301 SUNBED
E
X1
○
2
STEP 3:
Attach the assembled Leg (3) to Bed Frame (2), then twisting the Socket (E) into the leg hole, but not tighten.
the pre-drilled hole on the bottom of Bed Frame (2) with Socket Spanner (E) as shown. Repeat the same
steps for the other three Legs (3) .
Hardware & Tools required
STEP 4:
Insert 2 pieces of Bolts (A) with 1/4" Washers(B) through the two holes of one of Leg (3) into the Bed
Frame(2) by hand, pls don't tighten it fully, but make sure the Leg(3) is aligned with Bed Frame (2).
After that, pls use Allen Key(D) to tighten 2 pieces of Bolts (A) fully. And use Allen Key(D) and the top
Scoket (E) to tighten Long Screw Bar(G) fully. Repeat the same steps for the other three Legs (3).
Hardware & Tools required
D
X1
E
X1
X8
B
X8
A
○
D
○
E
○
3
○
B
○
A
○
2
○
D
Attach the assembled Leg (3) into the Bed Frame (2), then twist the Socket (E) into the hole of the Leg (3) and
make sure Long Screw Bar (G) is attached into the middle hole of the corner of the Bed Frame (2).
○
E
○
3
○
2
○
G
Insert 2 pieces of Bolts (A) with 1/4" Washers (B) through the holes of the Leg (3) into the Bed Frame (2) by
hand, pls don't tighten it fully, but make sure the Leg (3) is aligned with Bed Frame (2). After that, use Allen
Key (D) to tighten 2 pieces of Bolts (A) fully. And use Allen Key (D) and the top Socket (E) to tighten Long
Screw Bar (G) fully. Repeat the same steps for the other three Legs (3).

Customer Service 908-368-1025 ︱ www.modwayfurniture.com
P age 4 of 5
EEI-3301 SUNBED
○
3
○
3
○
3
○
2
STEP 5:
Insert 4 pieces of Tube Plugs (F)into the bottom hole of Legs (3) as shown and use Hammer (not
included) to tighten it fully.
○ F
F
Hardware & Tools required
STEP 6:
Carefully turn over the assembled Bed Frame(2) and open the adjustable backrest of the forepart
as shown.
○
I
○
I
F
X4
I
X1
Insert 4 pieces of Tube Plugs (F)into the bottom hole of the Legs (3) as shown and use Hammer (not
included) to tighten it fully.
Carefully turn over the assembled Bed Frame (2) and open the adjustable backrest of the forepart as
shown.

Customer Service 908-368-1025 ︱ www.modwayfurniture.com
P age 5 of 5
EEI-3301 SUNBED
Rope
Rope
STEP 7 :
Put the Cushion (1) on the Bed Frame (2) and tie 6 pieces of ropes on the back of the Cushion (1) into the
corresponding Bed Frame (2).
Assembly is complete. Your SUNBED is ready to be used now!
○
1
○
2
Put the Cushion (1) on the Bed Frame (2) and tie 6 pieces of ropes on the back of the Cushion (1) into the
corresponding Bed Frame (2).