Monacor TVCCD-187HCOL Manual

Instruction Guide
CTAB-120IR_1200
Printed in KOREA
12x AF Zoom ICR Day/Night IR Bullet Camera
12x AF Zoom ICR Day/Night
IR Bullet Camera

1
12x AF Zoom ICR Day/Night IR Bullet Camera
INFORMATION - This equipment has been tested and found to comply with
limits for a Class A digital device, pursuant to part 15 of the FCC Rules & CE Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
◆Do NOT use power sources other than those specified.
◆Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING - Changes or modifications not expressly approved by the manufacturer
could void the user's authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:

2
12x AF Zoom ICR Day/Night IR Bullet Camera
3
12x AF Zoom ICR Day/Night IR Bullet Camera
Features 4
Warnings and Precautions 6
Names and Functions of Parts 9
Dimensions 11
Installation 12
Troubleshooting 31
Specifications 33
Components 8
■SUN SHIELD
■LENS
■PHOTO SENSOR
■FOCUS LEVER
■ZOOM LEVER
■JOG SHUTTLE SWITCH
Cable Connections 13
How to Operate the Bracket 14
How to Use the Camera 15
■Using OSD icons 15
■Main Menu 15
ㆍCAMERA SET
ㆍINTELLIGENCE
ㆍPRIVACY ZONE
ㆍPRESET
ㆍOTHER SET
ㆍCOMMUNICATION
ㆍSYSTEM INFO
16
24
26
27
28
29
30
■Contents

4
12x AF Zoom ICR Day/Night IR Bullet Camera
5
12x AF Zoom ICR Day/Night IR Bullet Camera
Additional Functions
SYNC (INT/LL), SENS-UP, FLIP (H/V-REV),
D-ZOOM, DETAIL and PRIVACY functions
are provided.
Controlled by OSD Menu
The camera can be controlled by selecting
text displayed on the monitor screen.
Intelligent Video (Moved/Fixed)
This Camera provides built-in capability for
video content analysis. Operational modes
include fixed mode (appear the object) and
moved mode (disappear the object).
Photo Sensor & IR LED (30pcs)
IR LEDs are auto switching according to
the control of photo sensor.
A/F 12x Optical Zoom
The built-in optical zoom lens is ahighly
durable component. It features autofocus,
auto iris and zoom functions.
■Features Warning ■
The camera requires periodic inspection.
Contact an authorised technician to carry out the inspection.
Stop using your camera when you find it malfunctioning.
If the camera emits smoke or is unusually hot for a long period,
a fire may be caused.
Do not Install the camera on a surface that can not support it.
If the camera is installed on an inappropriate surface, it may fall
and cause injury.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not dis-assemble the camera.
It may result in an electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in a fire or other hazards.
Filter Changeable Day&Night
This camera has a function that automatically
selects the mode that is appropriate for daytime
or night-time conditions. The COLOR mode
operates in daytime conditions to provide
optimum colors and BW mode operates in
nighttime conditions to enhance the definition
of the image.
High Resolution
Featuring 600TV line horizontal resolution
incolor mode and 700TV line horizontal
resolutionin BW mode, the camera features
Sony's 410,000 pixel CCD and captures clean,
noiseless, high-quality images.
CCVC (Camera Control via
Coaxial cable)
This is a remote control function that overlaps
the coaxial cable (for a transfer of the video
signal) with the control signal. In installation
or repair, this helps you control the
communication controller (optional) without
additional cabling.
※Coaxial Controller (Option)
Weatherproof (IP66)
DNR (Digital Noise Reduction,
2D+3D)
The DNR technology eliminates noise thus
generating a distinct and clear image. This
camera DNR function utilizes both an adaptive
2D Filter reducing noise in the brightness of
the image and an adaptive 3D Filter reducing
noise caused by movement.

6
12x AF Zoom ICR Day/Night IR Bullet Camera
7
12x AF Zoom ICR Day/Night IR Bullet Camera
ㆍIf the camera is exposed to spotlight or an object reflecting strong light,
smear or blooming may occur.
ㆍPlease check the power supply satisfies the normal specification before
connecting the camera.
Do not install the camera in
extreme temperature conditions.
Do not install the camera under
unstable lighting conditions.
Do not touch the front lens of the
camera.
Only use the camera under conditions where
temperatures are between -10˚C and +50˚C.
Be especially careful to provide ventilation
when operating under high temperatures.
It can cause the image quality to be poor.
Severe lighting change or flicker can cause
the camera to work improperly.
This is one of the most important parts of
the camera. Be careful not to leave fingerprints
on the lens cover.
Do not install or use the camera in an
environment where the humidity is high.
It can cause malfunctions to occur. It can damage the CCD.
Do not drop the camera and protect
it from physical shocks.
Never keep the camera pointed
directly at strong light.
If exposed to radioactivity the CCD will fail.
Do not expose the camera to
radioactivity.
■Precautions

8
12x AF Zoom ICR Day/Night IR Bullet Camera
9
12x AF Zoom ICR Day/Night IR Bullet Camera
1. DAY & NIGHT
IR BULLET CAMERA
2. SCREWS
4. INSTRUCTION GUIDE
3. WRENCH
2. ALLEN HEAD BOLT
① SUN SHIELD
② LENS : 12X AF Optical Lens.
③ PHOTO SENSOR
④ FOCUS LEVER
⑤ ZOOM LEVER
⑥ JOG SHUTTLE SWITCH
①
②
③
④
⑤
⑥
■
Components Names and Functions of Parts
■

10
12x AF Zoom ICR Day/Night IR Bullet Camera
11
12x AF Zoom ICR Day/Night IR Bullet Camera
■
Names and Functions of Parts
Names and Functions of Parts
■
Service connector for easy installation of the camera.
- A service monitor can be connected to the camera, allowing the operator to
easily adjust camera angles and settings locally during installation.
SET : Used to access menu mode and for configuration.
▲: Moves cursor up in the menu screen.
▼: Moves cursor down the menu screen.
◀: Moves cursor left in the menu screen.
: Parameter change.
▶: Moves cursor right in the menu screen.
: Parameter change. (unit : mm)
Dimensions
■
90.0
90.3 245.9
130.8
80.0
83.0 165.0
149.0
⑥ Jog Shuttle Switch
LCD

VIDEO-COAX
RS-485
POWER
AC24V
DC12V AC24V
DC12V AC24V DC12V
12
12x AF Zoom ICR Day/Night IR Bullet Camera
13
12x AF Zoom ICR Day/Night IR Bullet Camera
■Installation
■Installation
Rear Case
Flange
Sun Shield BoltSun Shield
Flange adaptor
TP 4 x 20
Allen Head Bolt
M4 x 10
Switch Cover
Flange Nut
Front Case
Body Case
1. Bracket & Camera Mounting
- Affix the bracket to the mounting surface.
- Use the supplied screws to attach to the mounting surface using the
pre-drilled holes in the bracket.
2. Power Connector & Monitor Impedance
- Use a DC12V/1A regulated PSU or AC24V 1A.
- To avoid fire or shock hazards, always use a CE marked PSU.
- Set the monitor impedance switch to 75Ω. Check the impedance
switch if the screen is blurred.
3. Sunshield Mounting
- After completing view & focus adjustments, clip the sunshield into place.
4. VBS Extra
- Open the switch cover and connect VBS Extra to 2p connector.
Cable Connections
■

14
12x AF Zoom ICR Day/Night IR Bullet Camera
15
12x AF Zoom ICR Day/Night IR Bullet Camera
②
③
①
①Loosen the Bolt
Rotate the camera body what want your direction and tighten the Bolt.
(360˚rotation)
②Loosen the Bolt
Rotate the camera body what want your direction and tighten the Bolt.
(90˚rotation)
※Due to the size and weight of this product, it is recommended that the
installer hold on to the mounting bracket junction instead of the camera
itself while tightening the bolt ②.
③Loosen the Flange Nut
Rotate the camera body what want your direction and tighten the Flange Nut.
(360˚rotation)
■How to Operate the Bracket
How to Use the Camera ■
■ Using OSD icons
ㆍ◀ ▶: If these icons appear in the left and right corner of a menu item,
you can use them move to the previous or next menu.
ㆍ(EXIT) : Exits the menu setup screen.
Before exiting the setup screen, select <SAVE> to save your settings
to the whole menus, or <QUIT> to cancel them.
ㆍ(RET) : Saves your settings and returns to the previous screen.
ㆍ(HOME) : Returns to the main menu.
ㆍ(SAVE) : Use this icon if you want to save your settings after you
specified the mask area and privacy area, etc. Once you saved your
settings, the changes remain intact even if you select <QUIT> on exit.
ㆍ(DEL) : Use this icon if you want to delete a mask, or privacy area, etc.
Once you deleted your settings, the deletions remain valid even if you
select <QUIT> on exit.
ㆍ: This icon appears in the right of a menu containing sub menu items.
■ Main Menu
This is the first screen you ever see when you turn on the camera where
you can set the camera environment to your needs.
ㆍCAMERA SET : You can configure
the camera settings.
ㆍINTELLIGENCE : Offers motion
detection and tracking functions.
ㆍPRIVACY ZONE : You can configure
the privacy settings.
ㆍPRESET : You can set the PRESET
POSITION.
ㆍOTHER SET : You can reset the
camera, or adjust the OSD color to
your preference.
ㆍ COMUNICATION : Configures the settings pertaining to RS-485 communication.
ㆍSYSTEM INFO : Shows the system information such as the camera version
or communication settings.
** MAIN MENU **
CAMERA SET
INTELLIGENCE
PRIVACY ZONE
PRESET
OTHER SET
COMMUNICATION
SYSTEM INFO

16
12x AF Zoom ICR Day/Night IR Bullet Camera
17
12x AF Zoom ICR Day/Night IR Bullet Camera
■How to Use the Camera
CAMERA SET
You can configure the general settings of the camera module.
◀CAMERA SET ▶
CAMERA ID
IRIS
MOTION
DNR
SHUTTER
SENS-UP
FLICKERLESS
DIS
▼
OFF
ALC
(F.FAST) ---
MID
(OFF) ---
AUTO X4
OFF
OFF
◀CAMERA SET ▶
CAMERA ID
IRIS
AGC
DNR
SHUTTER
SENS-UP
FLICKERLESS
DIS
▼
OFF
ALC
(VERY HIGH) ---
MID
(OFF) ---
FIX X2
(OFF) ---
OFF
▣CAMERA ID ▣
ABCDEFGHIJKLMNOPQRSTYVWXYZ0
123456789 :? - +*()/
.................................
.................................
SP▶▶ ◀◀SP LOCATION
1. Select <MAIN MENU> -
<CAMERA SET>.
The Camera Setup menu appears.
2. Change the settings as necessary,
or select an item to check.
●CAMERA ID
Provide the ID and location for a camera that displays on the screen.
1. Select <CAMERA SET> -
<CAMERA ID>.
2. Use ▲▼◀▶ to select a desired
character, then press [ENTER].
In the lower input box of the screen,
the selected character will be entered.
※You can enter up to 54 characters
including alphabets, numbers and
special characters.
ㆍLOCATION : Specify the display
position of the camera ID.
3. When done, press [ENTER].
The camera ID will be displayed in the specified position.
●IRIS
The IRIS menu is useful if you set to adjust the intensity of radiation incoming
to the camera.
▣ALC ▣
[ 00] ----l----
BLC
USER
LEVEL
BACKLIGHT
AREA
<SIZE>
<LOCATION>
▣MANUAL ▣
[ 00] ----l---- LEVEL
ㆍALC : Adjust the open and close
of the iris.
- LEVEL : Select an overall brightness
level.
- BLC : With <BACKLIGHT> set to
<BLC>, you can specify the BLC area.
With AREA set to <USER>, you can
specify the position and size.
ㆍMANUAL : Adjust the iris level
manually.
• The overall brightness target of a
camera will be set to ALC level 0,
while the iris can be adjusted
manually.
●AGC
With this, you can adjust the AGC level
of a camera. With AGC active, if the
signal strength falls below the standard
level, AGC will amplify the video signal
to automatically improve the sensitivity.
If <SENS-UP> is set to <OFF> or <FIX>
mode, the <MOTION> menu will switch
to <AGC>. With the USER ( ) submenu
selected, press [ENTER] to display the
corresponding screen. In this mode, you
can select from VERY LOW to VERY
HIGH in 16 levels, enabling deeper,
wider choices to your convenience. With the FIX ( ) submenu selected, press
[ENTER] to display the corresponding screen. In this mode, you can select an
individualized mode in 16 levels, regardless of the brightness.
•As long as the DAY/NIGHT menu is set to AUTO in Camera Setup, the
AGC menu is not available.
•As long as FLICKERLESS is set to ON, the AGC mode is not available.
•If you set BACKLIGHT to WDR, the AGC fix mode is not available.

18
12x AF Zoom ICR Day/Night IR Bullet Camera
19
12x AF Zoom ICR Day/Night IR Bullet Camera
■How to Use the Camera
◀CAMERA SET ▶
CAMERA ID
IRIS
AGC
DNR
SHUTTER
SENS-UP
FLICKERLESS
DIS
▼
OFF
ALC
(VERY HIGH) ---
MID
1/120
(OFF) ---
(OFF) ---
OFF
DAY/NIGHT
WHITE BAL
FOCUS MODE
ZOOM SPEED
DISPLAY ZOOM
DIGITAL ZOOM
DETAIL
V-SYNC
AGC COLOR SUP
▼
▲AUTO
ONEAF
[3]
OFF
OFF
[2]
(INT) ---
MID
▣AUTO ▣
BURST
DAY→NIGHT
BRIGHTNESS
DWELL TIME
NIGHT→DAY
BRIGHTNESS
DWELL TIME
MASK AREA
OFF
MID
2SEC
MID
5SEC
1 2
●DIS (Digital Image Stabilization)
If you set it to <ON> for a camera that is trembled or vibrated from an ambient
change, this will automatically compensate for the flicker on the screen.
•If you set <DIS> to <ON>, the image will be enlarged with digital zoom
as much area as compensated. (Approximately 1.2 times of the optical
zoom factor) If you set the digital zoom to a larger ratio than the actual
enlargement for compensation, the <DIS> function will be disabled.
•<DIS> may not work properly in the following images :
Single-colored flat image / Low contrast scene / High frequency image
taken under a fluorescent lamp / Regular-patterned image
●DAY/NIGHT
You can specify a recording mode according to the scene.
1. Select <CAMERA SET> -
<DAY/NIGHT>.
2. Select a screen transition mode
according to the illumination, and
set options as appropriate.
ㆍDAY : Fixed to DAY mode,
regardless of the scene.
ㆍNIGHT : Fixed to NIGHT mode,
regardless of the scene.
If BURST is set to <ON>, the burst
signal will be output along with the
black-andwhite composite video
signal.
ㆍAUTO : According to the luminance,
this will switch DAY to NIGHT mode,
or vice versa.
- BURST : If set to <OFF>, the burst
signal will not be output in NIGHT
mode.
- DAY→NIGHT BRIGHTNESS :
Specify the brightness level
switching from COLOR to BW filter.
Adjusting from HIGH to LOW will
cause to switch the filter in a darker
screen.
●MOTION
You can specify a level of AGC for controlling the camera motion.
This is available only of the SENS-UP menu is set to AUTO.
Select F.FAST if you want to monitor a very fast moving object in a low contrast
scene, and S.SLOW if monitoring a very slow moving, inanimate object in the
same condition.
※As long as DAY/NIGHT is set to <AUTO>, the <MOTION> menu is not
available.
●DNR
Reduces the noise on the camera image. The higher the level is, the greater
the effect is.
Set it to <USER> to specify the level.
●SHUTTER
You can select a fixed fast electronic
shutter speed in 7 options ranging from
1/120 to 1/10k, which is mostly used to
take a picture of a fast moving object.
※As long as SENS-UP is set to AUTO,
FIXED / FLICKERLESS to ON /
BACKLIGHT to WDR, the SHUTTER
menu is not available.
●SENS-UP
Automatically senses the darkness level at night or in a low contrast scene,
and extends the accumulation time accordingly; you can select <AUTO>
or <FIX> for a bright and sharp image.
•If the SHUTTER menu is set to fixed electronic shutter mode, the
SENS-UP menu will not be available.
•If FLICKERLESS is set to ON, or BACKLIGHT to WDR, the FIX mode
of the SENS-UP menu is not available.
●FLICKERLESS
This will prevent possible screen distortion due to a mismatch between the
vertical sync frequency and the blinking frequency of the lighting; if set to
<ON>, the shutter speed will be fixed to 1/100 second.
※If SHUTTER is set to FIX, SENSE UP to FIX, and AGC to FIX, the
<FLICKERLESS> menu is not available.

20
12x AF Zoom ICR Day/Night IR Bullet Camera
21
12x AF Zoom ICR Day/Night IR Bullet Camera
■How to Use the Camera
▣MASK AREA ▣
<SIZE>
<LOCATION>
- DAY→NIGHT DWELL TIME :
Time required to determine the
filter switch.
- NIGHT→DAY BRIGHTNESS :
Specify the brightness level
switching from BW to COLOR filter.
Adjusting from HIGH to LOW will
cause to switch the filter in a darker
screen.
- NIGHT→DAY DWELL TIME : Time required to determine the filter switch.
- MASK AREA : If there exists a bright spot light source in a night scene,
you can specify the size and position as needed.
This will prevent an error in switching filter, or failure to determine the
filter switch in a night scene where a bright spot light source exists.
Any excessively bright area in a night scene will be MASKed.
※You can specify MASK 1 and 2 simultaneously.
※If <BACKLIGHT> is set to <BLC>, the MASK AREA function is not available.
ㆍEXT : The interface to an external alarm enables an automatic switch
between DAY and NIGHT mode.
•If you use an infrared light source while in AUTO mode, this may
cause a failure in AUTO SWITCH or AUTO FOCUS.
●WHITE BAL
If you need to adjust the color according to the ambient illumination, you
can use the <WHITE BAL> function.
Illumination is generally referred to as color temperature, which is
represented in a measurement of kelvin (K). Color temperatures for
ordinary lighting are as follows:
In the <WHITE BAL> menu, you can set a mode for correcting the
<WHITE BAL>.
- ATW1,2 : If you set the <WHITE BAL> menu to <ATW1> or <ATW2>
mode, this will monitor the change of the color temperature to correct
the <WHITE BAL> as needed. The following color temperature ranges
are assured in individual modes:
Blue sky
Rainy
Cloudy
Sunny
Partly Cloudy
Fluorescent lamp
Halogen lamp
Tungsten lamp
Candlelight
10000K
9000K
8000K
7000K
6000K
5000K
4000K
3000K
2000K
1000K
ATW1 : 2500K ~ 9300K (※1)
ATW2 : 2000K ~ 10000K
(suitable to sodium light source) (※2)
※1 : With <ATW1> mode active in a
color temperature environment
ranging beyond between 2500K
and 9300K, a proper white
balance value may not be
produced; if this is the case, you
are recommended to use
<ATW2> mode.
※2 : With <ATW2> mode active in a
mostly single color environment,
the display color and the actual
one may differ; so select a mode
as appropriate to your color temperature environment.
▣WHITE BAL ▣
DAY/NIGHT
MODE
RED
BLUE
R-GAIN
B-GAIN
DAY
AWC
[ 00] ----l----
[ 00] ----l----
[0128]
[0128]
▣WHITE BAL ▣
DAY/NIGHT
BRIGHTNESS
MODE
RED
BLUE
R-GAIN
B-GAIN
NIGHT
MID
AWC
[ 00] ----l----
[ 00] ----l----
[0128]
[0128]
1. Select <CAMERA SET> -
<WHITE BAL>.
2. Select a mode where you set the
<WHITE BAL>.
ㆍDAY : You can set the RED, and
BLUE value in DAY mode.
The screen will be displayed in
colors according to your settings.
※You can set the R-GAIN, and
B-GAIN value only in <AWC>
mode.
ㆍNIGHT : You can set the
<WHITE BAL> according to the
ambient illumination. If NIGHT mode
is set to <OFF>, the <WHITE BAL>
will operate in a mode specified in
DAY mode at all times; otherwise,
the screen will switch to a mode
specified in <DAY/NIGHT>.
You can set the RED, BLUE and
BRIGHTNESS value in DAY mode.
The screen will be displayed in
colors according to your settings.

22
12x AF Zoom ICR Day/Night IR Bullet Camera
23
12x AF Zoom ICR Day/Night IR Bullet Camera
■How to Use the Camera
3. According to the specified recording mode, select a <WHITE BAL>
mode with necessary options.
ㆍATW1,2 : The camera can automatically adjust the color temperature
in real time, according to the ambient conditions.
(Color temperature range 1: 2500K ~ 9300K, 2 : 2000K ~ 10000K)
ㆍAWC : Pressing [ENTER] on a desired item will perform ATW once.
※You can set the R-GAIN/B-GAIN value.
ㆍ3200K : Set the color temperature to 3200K.
ㆍ5600K : Set the color temperature to 5600K.
- BRIGHTNESS : Specify a brightness level switching from DAY mode
to NIGHR mode setting.
- RED : Adjust the strength of the red color.
- BLUE : Adjust the strength of the blue color.
- R-GAIN/B-GAIN : Specify the current color temperature manually.
•While you are working on the following objects, <AF> may not work
properly. If this is the case, use <MF> instead.
- Very bright object, or dominant object in a dark scene
- Object against the rear side of a moist or dirty glass
- A scene where nearby and distant objects co-exist
- White wall or single-colored object
- Venetian blinds and other horizontally striped objects
•It's a must to use AC 24V power supply when you select line lock.
DAY/NIGHT
WHITE BAL
FOCUS MODE
ZOOM SPEED
DISPLAY ZOOM
DIGITAL ZOOM
DETAIL
V-SYNC
AGC COLOR SUP
▼
▲AUTO
ONEAF
[3]
OFF
OFF
[2]
(INT) ---
MID
▣AF ▣
SENSITIVITY
NIGHT [5] MID
●FOCUS MODE
You can select a focus mode according to the angle that you adjusted for
camera recording.
- AF : This will monitor the screen
continuously to focus automatically.
If you adjust the focus manually, that
will operate the same as in <MF>.
This will also restore focus after the
operation of zoom.
- SENSITIVITY : Indicates the
sensitivity of auto focus, which you
can adjust between level 1 and
level 7. The closer your setting is to
7, the more sensitively the auto focus
function performs. The Night setting
is used when a strong light reflects
in a low contrast scene.You can set
it to OFF, LOW, MEDIUM, or HIGH;
set it to <HIGH> when there exist a
strong light such as street light.
- ONEAF : Restores focus after the
operation of zoom, and operates the
same as in <MF> unless the
operation of zoom is executed.
- MF : You can adjust the focus manually.
●ZOOM SPEED
You can adjust the zoom operation speed.
●DISPLAY ZOOM
You can set to display the zoom status on the screen.
※It will disappear in about 3 seconds if the zoom factor has no further
change.
●DIGITAL ZOOM
You can set the maximum allowable digital zoom ratio.
Digital Zoom will start operation after it is zoomed in to the maximum optical
ratio of x12. If you set DIGITAL ZOOM to x16, you can take a shot at up to
x192 (12x16).When you set DISPLAY ZOOM as on, you may see zoom
value on the screen.
●DETAIL
Used to adjust the vertical and horizontal distinction, respectively.
●V-SYNC
You can set the V-SYNC mode.
- If you select <INT>, the camera will use the internal synchronization.
- If selecting <LINE>, the camera will use an external power frequency
for synchronization. The LL-PHASE can be adjusted as appropriate.
●AGC COLOR SUP
You can adjust the color reproduction range according to AGC.

24
12x AF Zoom ICR Day/Night IR Bullet Camera
25
12x AF Zoom ICR Day/Night IR Bullet Camera
■How to Use the Camera
•If you set it to <DETECTION>, the <FIXED/MOVED> option of
ADVANCED menu will not be available.
•In following situations, motion detection and tracking function may
not work properly.
- When there is sudden changes of brightness
- When the device moves
- When a certain object¡¯s movement fills most of the framing area
- When there is difficulties in distinguishing the moving object and
background
•In following situations, FIXED/MOVED detection may not work properly.
- When multiple motions continue arbitrarily.
- When the object that is fixed continues to move in the same position.
- When a newly appearing object conceals another object that is moving.
•If more than one PRIVACY ZONE is specified, and PRIVACY SET
to <ON>, the PIP function is not available.
•As long as SENS-UP is set to FIXED, PIP menu is not available.
•According to the luminance, PIP will disappear if the SENS-UP menu
is set to AUTO.
REVERSE
POSI/NEGA
PIP
▲
OFF
+
OFF
●ADVANCED
You can detect motions and mark the video that contains such motion, and
enables tracking of the movement. (The auto PTZ function is not supported
for tracking an object.) Selecting the <FIXED/MOVED> option will mark a
region if an existing object disappears, or a new object appears and fixed
for a certain period of time.
●DISPLAY
When selected <ON>, it displays the motion detected and detection of
configured advanced function.
●MASK AREA
1. Select the number of the area to
be masked that will be excluded
from motion detection.
2. Select the mask number and set
the mask size and its coverage.
●REVERSE
You can reverse the video signal from
left to right, upside down, or vice versa
to your convenience.
●POSI/NEGA
You can set the video brightness signal
to normal or reverse.
●PIP
You can view a main image with a sub image on the same screen.
INTELLIGENCE
You can enable the motion detection and tracking functions.
◀INTELLIGENCE ▶
MOTION
ADVANCED
MASK AREA
DISPLAY
SENSITIVITY
RESOLUTION
ALARM OUT
OFF
OFF
1 2 3 4
ON
[4]
[3]
1. Select <MAIN ME NU> -
<INTELLIGENCE>.
2. Select each item and set
appropriately.
●MOTION
You can enable the motion detection
and tracking functions.
<SIZE>
<LOCATION>
▣MASK AREA ▣

26
12x AF Zoom ICR Day/Night IR Bullet Camera
27
12x AF Zoom ICR Day/Night IR Bullet Camera
** MAIN MENU **
CAMERA SET
INTELLIGENCE
PRIVACY ZONE
PRESET
OTHER SET
COMMUNICATION
SYSTEM INFO
■How to Use the Camera
•Setting one or more privacy zone and enabling privacy function will
disable the PIP function.
•For better privacy protection, make your privacy zone bigger than the
required, bigger by about 30%.
•Video portion of mosaic pattern or colored by the privacy zone setup
is not recoverable.
PRIVACY ZONE
You can set up to 8 privacy zones that will be hided for privacy of the subject
when recording.
PRESET
This function provides preset camera settings such as zoom and focus
so to enable quicker and easier accessing and monitoring, which supports
up to 512 presets.
◀PRIVACY ZONE ▶
1 2 3 4
5 6 7 8
PRIVACY SET
STYLE ON MOSAIC1
MOTION
FIXED/MOVED ON ON
▣ALARM OUT ▣
●SENSITIVITY
Sets the sensitivity of motion sensor.
●RESOLUTION
The bigger the resolution setting, the smaller the object that can be detected.
●ALARM OUT
You may set Alarm in, Delay time and
Alarm out option in Alarm setup menu.
The Delay time arranges from 1 to 60
seconds. It is set as 5 seconds in default.
If MOTION and FIXED/MOVED option
are set as on, camera would send off
alarm beep after detecting the moving
object. Whenever there is alarm signal,
camera would send off alarm beep if you set alarm as on.
<ZOOM>
PIXEL LEVEL
<SIZE>
<LOCATION>
▣PRIVACY ZONE SET 1 ▣
[4]
1. Select <MAIN MENU> -
<INTELLIGENCE>.
2. Select the number of the zone and
press [ENTER].
The Zone setup screen appears.
3. Select the <ZOOM> and press
[ENTER]. Using ▲▼◀▶ to locate
zoom position.
4. Select the <PIXEL LEVEL>.
Select the pixel level for the SIZE
and LOCATION settings.
1. Select <MAIN MENU> -
<PRESET>.
5. Using ▲▼◀▶ buttons to set the area of the privacy zone in order
(Upper left→Upper right→lower right →lower left). Finally you may
press ENTER to exit. While locating the point, please do not change
the corresponding direction of each point , otherwise, the picture in the
privazy zone would not be normally displayed.
6. Save the changes and move to the previous screen and select the
<STYLE>. Select the <COLOR> and pick a desired color.

28
12x AF Zoom ICR Day/Night IR Bullet Camera
29
12x AF Zoom ICR Day/Night IR Bullet Camera
COMUNICATION
You can set the RS-485 communications setting in regard of the camera.
•Note that the resetting the system to the factory default will erase all
settings data.
■How to Use the Camera
OTHER SET
You can reset the system by running FACTORY DEFAULTS, or set the
font color etc.
◀PRESET ▶
O H 1 2 3 4
5 6 7 8 9
10 11 12 13 14
15 16 17 18 19
20 21 22 23 24
25 26 27 28 29
30 31
◀1/8 ▶
HOME RETURN OFF
2. Select the preset number.
ON
POSITION
PRESET ID
▣PRESET NO. 1 ▣
3. Select <POSITION>.
4. Set <PRESET ID> to <ON> and
enter the name.
※For entering the name, refer to
"CAMERA ID". (page 22)
◀OTHER SET ▶
LANGUAGE
FACTORY DEFAULTS
OSD COLOR
ENGLISH
BW
◀COMMUNICATION ▶
PROTOCOL
BAUD RATE
ADDRESS
PELCO-D
2400
1
1. Select <MAIN MENU> -
<OTHER SET>.
2. Select each item and set
appropriately.
●LANGUAGE
You can set the language of the user
interface using ◀▶ buttons.
●FACTORY DEFAULTS
When selected, the <FACTORY DE
FAULTS> screen appears and you can
reset all settings to the factory default
settings by selecting the <OK>.
However, the protocol, baud rate,
address and the language settings will
not be reset.
●OSD COLOR
Selects the color of the on-screen display font.
▣FACTORY DEFAULTS ▣
OK CANCEL
1. Select <MAIN MENU> -
<COMMUNICATION>.
2. Select each item and set
appropriately.
•PROTOCOL, BAUD RATE,
ADDRESS :
You can manually set the protocol,
baud rate and address.

30
12x AF Zoom ICR Day/Night IR Bullet Camera
31
12x AF Zoom ICR Day/Night IR Bullet Camera
◀SYSTEM INFO ▶
TYPE
PROTOCOL
ADDRESS
BAUD RATE
SERIAL NO.
CAMERA VER.
4_12ZMD_NOR_P
PELCO-D
1
2400
000000000000000
v2.00_100612
SYSTEM INFO
You can check the system information.
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an
authorized technician.
Problem
Nothing appears on
the screen.
The image on the
screen is dim.
• Check the power connections.
• Check the VIDEO signal line connection.
• Make sure the lens is clean. Clean the lens with
a soft clean lint free cloth.
• Adjust the monitor contrast & brightness controls.
• Re-position the camera if necessary.
The image on the
screen is dark.
• Adjust the contrast control of the monitor.
• If you have an intermediate device, set the 75Ω
/ Hi-z properly.
The camera is not
working properly, and
the surface of the
camera is hot.
• Check that an appropriate power source is
connected to the camera.
Solution
■How to Use the Camera Troubleshooting ■
1. Select <MAIN MENU> -
<SYSTEM INFO>.
2. The current system information is
displayed.
Color is not correct. • Check the WHITE BAL settings in the CAMERA
SET menu.

32
12x AF Zoom ICR Day/Night IR Bullet Camera
33
12x AF Zoom ICR Day/Night IR Bullet Camera
Specifications ■
■Troubleshooting
Problem
The screen flickers
continually.
• Check that the camera is not facing toward the
sun.
RS-485
communication fails.
• Check the polarity between the RS-485 Control
Port and the RS-485 cable.
• Check the RS-485 Communication default settings.
* RS-485 Communication default settings are :
Solution
RS-485 Control Port 485 Control Board Connection Port
485+ (+) CONNECTION TERMINAL (TRX+)
( - ) CONNECTION TERMINAL (TRX-) 485 -
Item
Initial value
BAUD RATECamera ID
1 2400
ITEM
Power Supply
Power Consumption
Effective Pixels
Image Sensor
Scanning System
Synchronization
Frequency
Resolution
Video Output
S/N Ratio(Y signal)
Min. Illumination
Gain Control
White Balance
Optics
Digital Zoom
Angle Field of View
Focus
Iris Control
Camera ID
Back Light Compensation
Shutter Speed
O.S.D
Sens-up
Motion Detection
Privacy Function
DNR
Zoom Movement Speed
AC24V / DC12V Dual Power
MAX. 640mA (AC24V) / MAX. 800mA (DC12V)
768(H) x 494(V) 752(H) x 582(V)
1/4" 410K/470K Sony Super HAD ⅡCCD
2:1 Interlace
INT / LL Selectable
15.734KHz(H), 59.94Hz(V) 15.625KHz(H), 50Hz(V)
600 TV Lines (Min.) : Color (Wide)
700 TV Lines (Min.) : B / W (Wide)
CVBS : 1.0Vp-p (75 Ohm Load)
52dB (AGC OFF)
0.7Lux/F1.65(50 IRE) : Color, 0 Lux with IR LED(30pcs) : B/W
OFF, LOW, MIDDLE, HIGH
ATW1/ATW2 / AWC / MANUAL Mode (3200˚K, 5600˚K, R/B Gain adjustment)
12X, f=3.69 to 43.32mm(F2.8)
OFF / ON (X2 ~ X12)
H : Appr. 54.44˚(Wide) to 4.64˚(Tele)
V : Appr. 41.42˚(Wide) to 3.52˚(Tele)
Auto
AUTO / MANUAL
OFF / ON (Displayed 54 characters)
OFF / BLC Selectable
AUTO (X256~1/120sec~1/10000) AUTO (X256~1/120sec~1/10000)
Sens-up and Sens-up Limit is
Selectable, Flickerless
Built-in
AUTO / OFF (Selectable x2 ~ x256)
OFF / ON (4 Programmable Zone per Screen)
OFF / ON (8 Programmable Zone per Screen)
OFF / LOW / MIDDLE / HIGH / USER
1.9 sec : Wide to Tele 1.84 sec : Wide to Tele
RS-485
-10˚C ~ +50˚C / 95% RH max.
Approx. 1,130g
NTSC PAL
Communication
Operating Temperature/Humidity
Weight