Morris MFS-16220 User manual

STAND FAN
OPERATING INSTRUCTIONS
MODEL: MFS-16220
READ THESE INSTRUCTIONS CAREFULLY AND STORE THEM FOR
FUTURE REFERENCE!

Read Rules for Safe Operation and Instructions Carefully.
1. Ifthesupplycordisdamaged,itmustbereplacedbymanufacturer
oritsserviceagentorasimilarlyqualifiedpersonin orderto avoid
ahazard.
2. Toprotectagainsttheriskofelectricalshock,donotimmersethe
unit,cordor plugin water or otherliquid.
3. Thisappliancecanbeusedbychildrenagedfrom8yearsand
aboveandpersonswithreducedphysical,sensoryormental
capabilitiesorlackofexperienceandknowledgeiftheyhavebeen
givensupervisionorinstructionconcerninguseoftheappliancein
asafewayandunderstandthehazardsinvolved.Childrenshall
notplaywiththeappliance.Cleaningandusermaintenanceshall
notbemadebychildrenwithoutsupervision.
4. Whentheapplianceisnotinuseandbeforecleaning,unplugthe
appliancefromtheoutlet.
5. KeepelectricalappliancesoutofreachfromChildrenorinfirm
persons.Donotletthemusetheapplianceswithoutsupervision.
6. Whenthefanwasassembled,therotorbladeguardshallnotbe
takenoffanymore
- Priorcleaningunplugthefan.
- Therotorguardshallnotbedissembled/openedtocleanthe
rotor blades.
- Wipethefanenclosureandrotorbladeguardwithaslightly
damp cloth.
1. Never insert fingers, pencils, or any other object through the grille when fan is
running.
2. Disconnect fan when moving from one location to another.
3. Be sure fan is on a stable surface when operating to avoid overturning.
4. DO NOT use fan in window, rain may create electrical hazard.
5. Household use only.
1
RULES FOR SAFE OPERATION
WARNING
CAUTION

1 2 3 4 5 6 7 8
1. FrontGrill
2. Spinner
3. Blade
4. PlasticNut
5. RearGrill
6. Motor Shaft
7. Motor
8. Clutchknob
9. Handle
10. Thumb screw
11. Internal Pole
12. Heightadjustmentring
13. Extension Pole
14. Base
15. 7-shapeBolt
16. Controlpanel
16
9
10
11
12
13
14
15
1. Unscrewthe7-shapeBoltfromtheExtensionPole.(Fig.1)
2. Inserttheextensionpoleintothebaseandtightenthe7-shapeBolt.(Fig.2)
3. Fromtheextensionpoleloosentheheightadjustmentringandadjusttheinternal
poletothedesiredheight.(Note:If youcan’t findtheinternalpole,itmustslide
insidetheextensionpole.Youcanpullitoutfrom theextensionpole.)(Fig.3)
4. Toattachthe headunittotheextensionpole,loosenthe thumbscrewon the
bottomof the headunit.Placetheheadunitonthe internalpoleandtighten the
thumbscrewinalignmentwiththegrooveontheinternalpole.(Fig.4)
CAUTION:Heightadjustmentringmustbefullyfastenedbeforetheassemblyof
themotorsectiontotheextensionpole.
2
ASSEMBLY OF BASE & COLUMN UNIT
PART FIGURE

Fig.1
Fig.2
Fig.3
Fig.4
Mounting hole
Thumb screw
Loosen
Annular groove
1. Unscrew the spinner clockwise (or take the spinner out from the bag) and the
plastic nut counterclockwise to remove both of them. Fix the rear grill to the
motor then tighten the plastic nut again. (Fig.5)
2. Insert the blade into shaft, and make sure the rotor shaft pin is fitted into groove
of the blade. Turn the spinner counterclockwise to tighten the blade. (Fig.6)
3. Fix the front grill and the rear grill with circlip clip and then fasten the circlip clip
and lock the screw and nut. (Fig.7)
Fig.5 Fig.6 Fig.7
Screw
3
GRILL & FAN BLADE ASSEMBLY

I. Remote Controller (Fig.8)
“”ON/OFF KEY
This key is for switching on the fan. The fan will be started at
medium. After 2 seconds, it will automatically over to low step.
Press this key again if the fan needs to switch off.
“”TIMER KEY
Press the timer key repeatedly, the fan will off after "1-2-3-4-
5-6-7-8" hour.
Fig.8
“” SPEED KEY
After the fan has started, this key serves as a speed selector in the sequence from
“low-medium-high-low” when this key being touched repeated or continuously.
II. Control Panel (Fig.9)
These keys of the control panel may be used as same
as of the remote controller.
II. OscillationControl
To make the fan oscillate, press the clutch knob located
on the top of the motor housing. To get the directional
airflow, pull the clutch knob up to its initial position.
III. Tilt Adjustment
To adjust the air flow upward or downward, push the
guards lightly to the desired direction.
IV. Height Adjustment
The height of the fan can be adjusted by loosening the locknut, carefully raising or
lowering the fan and firmly re-tightening the locknut.
1. Press dawn on the battery compartment cover
and slide it out.
2. Insert the batteries, making sure that the positive
terminals are facing the proper way.
3. Replace the cover.
4
BATTERIES INSTRUCTIONS
(not included)
OPERATING INSTRUCTIONS
---ON/OFF SPEED
BUTTON
---TIMER BUTTON
Fig.9

1. “Do not dispose of batteries in fire, batteries may
explode or leak.”
2. -Do not mix old and new batteries.
3. -Do not mix alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium) batteries.
Point the remote controller at the receptor on body of the fan and press the desired
button. The remote controller will work at distances of up to roughly five meters and
the angle of 30 degree included between right and left from the receptor.
The batteries must be removed from the remote controller before it is scrapped and
that they are disposed of safely.
The windings of the motor have a thermal-fuse that burns out and the fan switches
off and temperature of the motor is no longer going up so that plastic parts of the fan
don’t subject to deformation so far so to be burned by the overheat if the motor is
overheat for any unexpected reason.
The fan requires little maintenance. Do not try to fix it by yourself. Refer it to
qualified service personnel if service is needed.
1. Before cleaning and assembling, fan must be unplugged.
2. To ensure adequate air circulation to the motor, keep vents at the rear of the
motor free of dust. Do not disassemble the fan to remove dust.
3. Please wipe the exterior parts with a soft cloth soaking a mild detergent.
4. Do not use any abrasive detergent or solvents to avoid scratching the surface.
Do not use any of the following as a cleaner: gasoline, thinner.
5. Do not allow water or any other liquid into the motor housing or interior parts.
1. Be sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with a soft cloth moisten with mild soap.
Thoroughly remove soap film with dry cloth.
5
CLEANING
MAINTENANCE INSTRUCTION
OVERHEAT PROTECTION OF THE MOTOR
HOW TO USE THE REMOTE CONTROLLER CORRECTLY
BATTERY WARNING AS BELOW

NOTICE ABOUT RECYCLING
Your product is designed and manufactured with high
quality materials and components which can be
recycled and reused.
This symbol means that electrical and electronic
equipment, at their end-of-life,
should be disposed of separately from your household
waste. Please dispose of this equipment at your local
community waste collection/ recycling centre.
In the European Union there are separate collection systems for used
electrical and electronic products.
Please help us to conserve the environment we live in!
DECLARATION OF CONFORMITY
Herewith, Amiridis-Savvidis S.A. states that this product, complies
with the requirements of below directives:
EMC-Directive: 14 / 30 / EU
Low Voltage Directive: 14/ 35 / EU
CE Marking: 93 / 68 / EEC
RoHS Directive: 11 / 65 / EU
The detailed declaration of conformity can be found at www.morris.gr
Exclusive importer in Greece:
Amiridis –Savvidis S.A.
87A, 17th Noemvriou str, P.C. 55534
Thessaloniki –Greece
T: [phone] | F: [phone]
www.amiridis-savvidis.gr
www.morris.gr